667887

Eurom Sani-Fanheat 2000 Manual

21
Zoom out
Zoom in
Previous page
1/56
Next page
21
therefore may not be used in a lying, leaning, hanging or standing position! The
wall on which the device is hung has to be firm, flat and perfectly vertical and
made from non-inflammable material that cannot melt. It has to be at least 20 cm
away from side walls and the bottom has to be at least 180 cm.
The heater has to preferably (and definitely in damp rooms) be positioned at and
permanently connected to an electric socket. This connection may only be made
by a qualified electrician and, for that reason, is not described here.
In this booklet, for reasons of safety, use with a plug should be assumed; when
there is a permanent connection, any passages about the plug do not apply.
Drill 2 holes (7 mm.) in the wall at the selected spot: horizontal to one another with
a distance of 18,7 cm. Insert plugs into the holes and insert screws into the plugs
(included). Leave the screws protruding by 5 mm. Hook the heater using the
suspension eyes over the screws, slide it as far as possible to the left and pull the
heater downwards.
Attach the heater using the materials supplied (see
diagram). Place the bracket on top of the heater with
the short side against the wall. Mark the location of
the hole on the wall and remove the heater. Drill a
hole at the marked spot and insert a plug. Now hang
the heater in place and screw the bracket to the wall,
as shown in the diagram. The heater is now
installed.
Switching on and operation
Check that the control button is ‘OFF’ (O).
Fully unwind the electric cable and insert the plug into a suitable 220/240V socket.
Turn the thermostat dial to + (clockwise as far as possible).
Switch the heater on by turning the control dial to one of the following three
positions:
Fan only (thermostat always to maximum)
I Heating at half power (1000W)
II Heating at full power (2000W)
The light at the front will turn on.
It is most economical to heat the space at full power, then to switch to half power
to maintain the temperature.
Both at half and full power, the fan rotates at the same speed; the difference
between the two lies in the number of heating elements in use.
Once the desired temperature is reached, turn the thermostat dial back slowly until
you hear a click. The temperature is now set. The heater will automatically switch
on and off to maintain the set temperature. When the heater switches off, the pilot
light turns off as well. To set a higher or lower temperature, turn the thermostat dial
either clockwise or anticlockwise.
To switch the heater off, set the power dial to ‘O’ (off). The pilot light will turn off.
The pilot light, in other words, indicates that the heater is switched on, not that the
heater is connected to the mains!
… 21 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eurom Sani-Fanheat 2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Sani-Fanheat 2000 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info