Manual Eurom Heat-Duct-Pro 3 (page 21 of 56) (English, German, Dutch, French, Swedish)

591494

Zoom out

Zoom in

1/56

 Make sure the heater is always in an upright position on a solid, flat, horizontal

and non-flammable surface.

 Make sure the heater is switched off (switch to O position), then plug into a

correctly functioning, properly grounded 230V-50Hz (Heat-Duct-Pro 3) / 400V-

50Hz. (Heat-Duct-Pro 9) socket.

Set-up and Operation

If the heater is being used for the first time (or if you want to reset the desired

temperature), turn the thermostat dial to the maximum position (clockwise as far as it

goes).

With the mode selector dial, adjust the heater to suit your preferences: fan only, half

power (only Heat-Duct-Pro 9) or high power.

Once the temperature in the area being heated has reached the right level, slowly

turn the thermostat dial anticlockwise until you hear a soft click; leave the dial in that

position. The heater will automatically maintain the temperature at this level. It does

this by switching the heating elements off and on when the temperature rises or falls

too much.

Note! After the thermostat has switched the heating elements off, the fan will keep

turning. This means that the air is constantly moved, allowing the heater to accurately

detect if the area is cooling down.

The thermostat dial is continuously adjustable (0-40°). A higher temperature is set by

turning it clockwise; a lower temperature by turning it anticlockwise.

Warning: When using for the first time, you might smell smoke. This is normal and

will disappear after a short while. It occurs because some residual oil is left behind

after the manufacturing process and gets heated up.

Aftercooling

The heater is supplied with an aftercooling system. When switching the heater off,

turn the control knob to "off". O. The heater will first ventilate in order to cool down

internally. This can take three or four minutes, depending on the ambient

temperature. Then the heater will switch itself off. Make sure that you then remove

the plug from the socket.

With a very high ambient temperature, the heater will keep on aftercooling. In this

case you can only switch it off by removing the plug from the socket.

Heat discharge hose

A heat discharge hose can be connected to the air vent in order to lead the heat to

another space.

To do this, use the special Heat-Duct-Hose: this has the right degree of heat-

resistance and is supplied with a matching clamp. Also for the hose: ensure that it

does not get too near to flammable materials!

Heat-Duct-Pro 3: 5 m. x 26 cm., Art.no. 33.241.4

Heat-Duct-Pro 9: 5 m. x 29 cm., Art.no. 33.242.1

Before use, check that the hose and clamp are fitted properly around the vent and

make sure that the hose never makes a bender smaller than 90°.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom Heat-Duct-Pro 3 in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 0,89 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom Heat-Duct-Pro 3 Manual

Product: