Manual Eurom CK401IP kachel (page 11 of 28) (English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish)

591307

Zoom out

Zoom in

1/28

Description

The CK401IP frost shield is an electrical convector heater

with a thermostat and an overheating safeguard. The light is

illuminated when the frost shield is switched on. The

CK401IP frost shield is intended to keep small domestic or

similar spaces frost-free. The heater may only be used when

mounted on the wall (never if it is standing up or lying down!)

and only for the purpose for which it was designed.

1 = air outlet grill

2 = pilot lamp

3 = thermostat dial

4 = air inlet grills

Location and Connection

 Remove all packaging material and keep out of reach of children. After removing packaging, check the

appliance for damage or other signs that could indicate a fault/defect/malfunction. In case of doubt, do not

use the appliance, but contact your vendor for inspection or replacement.

 Choose a suitable location for the heater, i.e. at least one metre away from any obstructions, walls or

inflammable materials (see also safety instructions).

 The heater needs to be mounted on the wall. Make sure the wall is solid, totally vertical and non-flammable.

Do not use wooden or synthetic walls! The distance between the bottom of the heater and the floor should

be at least 20 cm. The distance between the heater and the sidewalls should be at least 30 cm and the

distance between heater and ceiling at least 50 cm. Do not mount the appliance directly below or in front of

a socket.

 Loosen both screws on the

suspension bracket and fix the

assembly bracket horizontally to

the wall, using the screws

provided. Slide the heater back

over the bracket and secure

both screws at the side of the

bracket. Make sure the heater and bracket are securely attached and that the heater is

completely horizontal.

 If desired, the CK401IP can be permanently connected to the power supply by means

of a suitable junction box (not included). This procedure needs to be performed by a

professional! A disconnection device at a minimum distance of 3mm (e.g. an automatic

power switch, an on/off switch) must be provided for heaters which are permanently

connected to the power supply in order that they may be switched off.

Set-up and Operation

 The frost shield is now ready to use. Insert the plug into a suitable 220-240V-50Hz grounded socket to

switch on the heater. Only connect the heater to an earthed socket!

 To set the desired temperature, turn the thermostat dial to maximum (biggest dot, or clockwise as far as it

goes). Wait for the desired temperature to be reached and then slowly turn the knob until the pilot light goes

off. The desired temperature is now set; when the temperature in the immediate vicinity drops to under this

level the heater will switch on, as will the light. To set the temperature to a higher or lower level, turn the

thermostat dial to either 'maximum' (biggest dot) or 'minimum' (star).

  shield will keep the area frost-free (as

long as the area is not too big or too cold).

 The appliance will function even when set to the lowest level. To fully switch off the heater, you must remove

the plug from the socket (or, in case a switch has been 

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom CK401IP kachel in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Swedish, Norwegian, Finnish as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom CK401IP kachel Manual

Product: