Manual Eurom CK2003T (page 13 of 32) (English, German, Dutch, French, Swedish)

510011

Zoom out

Zoom in

1/32

 Decide where you want to mount the heater. Make sure that the heater has sufficient space around it at all times and

that no inflammable materials are located nearby (see also safety instructions). Do not place the heater behind a door!



top at least 150 cm from the ceiling, ceiling beams, etcetera.

 Attach two brackets (a left hand and right hand one) as suspension brackets to the wall. To do so, drill 2 holes 418,5

mm apart, at least 38 cm from the floor, on a completely horizontal line. Insert plugs and screw in the suspension

brackets with two long screws. Screw through the short side, with the short sides pointed towards each other and the

groove on the upper side.

 To make spacer brackets, attach the other two brackets to the

underside of the heate 

longer 

short sides pointing towards the floor and jutting out from the heater

in a straight line. Attach securely using the small screws. The groove

needs to be on a level with the rear of the heater.

 Slide the heater, with the gaps in the rear, over the suspension

brackets and lower the heater into the grooves. The spacer brackets

will ensure there is enough space between heater and wall.

 Mark the place where the spacer brackets need to be fixed to the

wall. Take the heater down, drill holes and attach plugs at the marked

spots. Mount the heater and screw in the spacer brackets with the

two remaining long screws.

Set-up and Operation

 Make sure the heater is turned off (mode selector dial to 0W, fan switched to OFF) and that the thermostat dial is set to

maximum (clockwise, as far as it will go). Now plug into an earthed, correctly functioning 220-240V / 50Hz socket. The

pilot light will switch on.

 Turn the mode selector dial to the desired position:

750W = low power heating (750 Watt)

1250W = medium power heating (1250 Watt)

2000W = full power heating (2000 Watt)

The heater will now start to heat the space.

 If so desired, the fan (turbo) can be switched on for more rapid and more effective heat distribution. Set the fan switch

to ON. Setting the switch to OFF switches off the fan.

 When the space has reached the desired temperature, turn the thermostat dial anticlockwise slowly until you hear a

click. In this position, the thermostat will maintain the current temperature by turning the heater on and off for a top-up,

if necessary. If so desired, you can now switch to a lower power level. For higher temperatures, turn the thermostat

dial clockwise, for lower temperatures anticlockwise.

 The heater can also be used as a fresh air fan. To do so, set the thermostat dial to its maximum position, switch on the

fan, but leave the mode selector dial on 0W.

 To switch off the heater, first switch off the fan, then turn the mode selector dial to 0W and unplug.

Safety features

The heater is fitted with a tipping safeguard which automatically shuts off the appliance if it inadvertently falls over. The

heater will function as normal once it is returned to its upright position but you are advised to switch if off, unplug and check

it for damage before using again. Do not use the heater in case of damage or malfunctioning. Have the appliance

inspected/repaired!

In case of internal overheating, the overheating safeguard will switch the heater off. This may occur if the heater cannot

give off enough heat or if it cannot draw in enough fresh air. As mentioned above, this is generally caused by (partially)

covering the heater, obstructing the air intake and/or outlet grills or installing the heater too close to a wall or something

similar. In case of overheating, switch off the heater and unplug. Give the heater time to cool down, remove the source of the

overheating and use as normal. If the problem persists or if you have not been able to trace the source of the overheating,

turn the heater off immediately and unplug. Contact a servicing point to have the heater repaired.

Cleaning and Maintenance

Keep the heater clean. Deposits of dust and dirt in the appliance are a common cause of overheating so these should be

removed regularly. Switch off the heater, remove the plug from the socket and allow the heater to cool down before cleaning

or carrying out maintenance work.

 Wipe the outside of the heater regularly with a dry or slightly damp cloth. Do not use aggressive soaps, sprays,

cleaners or abrasives, waxes, polishes or chemical solutions!

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Eurom CK2003T in the language / languages: English, German, Dutch, French, Swedish as an attachment in your email.

The manual is 0,75 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Eurom CK2003T Manual

Product: