806947

Eufab 16257 Manual

11
Zoom out
Zoom in
Previous page
1/36
Next page
11
Inserting the memory card
Make sure that the dashboard camera has been
switched o. Insert the micro-SD into the slot
(Position 2 in the overview). Pay attention to ensure
that the memory card is correctly positioned. The
contacts of the memory card must face in the direction
of the lens. Carefully push the memory card into the
slot until it engages with a soft click.
Clean the section of the windscreen where the camera
is to be mounted. Put the camera mount (Position 18
in the overview) into the mounting point (Position 6
in the overview) of the camera. Press the suction base
(Position 15 in the overview) against the windscreen.
Flip the lever (Position 16 in the overview). Undo the
coupling nut (Position 17 in the overview) on the ball
joint. Align the camera. Tighten the coupling nut up
again.
Plug the USB connector (Position 19 in the overview)
of the charging cable into the USB socket (Position 7
in the overview) of the camera. Lay out the charging
cable in such a way that it does not impede visibility
and does not hinder you during the journey. Plug the
vehicle connector (Position 20 in the overview) of the
charging cable into the 12 V socket of your vehicle.
Long press:
Switches the camera on/o.
Video recording is started directly after the camera is
switched on.
Brief press:
Switches the Power-LED (Position 5 in the overview)
on/o.
In Standby mode:
A brief press starts video recording (red dot ashes on
the display)
A second brief press stops video recording.
In Photo mode:
A brief press takes a photograph.
In Play mode:
A brief press plays the recorded video.
ON/OFF switch (Position 1 in the overview)
OK button (Position 10 in the overview)
Removing the memory card
Switch the camera o. To remove the memory card,
press down and release. The card will pop up and you
can remove it.
Removing the memory card with the
camera switched on may result in a loss of
data or damage to the device.
6.2 MEMORY CARD
6.3 INSTALLATION
6.4 CONNECTING THE CAMERA
6.5 FUNCTIONS
In Standby mode:
A brief press opens the menu for the video settings.
With the cursor buttons (Positions 11 and 13 in the
overview), you can select the various menu items.
Press the OK button to open the selected menu item.
Use the cursor buttons to select the setting in the
menu item, and conrm by pressing the OK button.
Settings in the video menu (symbol shows a
video camera in the top left of the display):
Resolution: FHD – HD - 720P 1280x720 - WVGA
848x480 - VGA 640x480
Loop recording:
Here, the camera records short video passages. When
the memory is full, the oldest recording will always be
deleted.
Switch o –1 minute –2 minutes –3 minutes –
5 minutes –10 minutes
Lighting compensation:
Here you can set the brightness of the video recording.
+2.0 …+0.0 … -2.0
Motion detector:
When the motion detector is activated, the
camera automatically starts recording when motion
is detected.
Switch o – switch on
Menu button (Position 3 in the overview)
19 USB connector
Figure 3: Charging cable
20 Vehicle connector
19
20
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eufab 16257 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 16257 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0.42 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info