807232

Eufab 11411 - Bike Two Manual

9
Zoom out
Zoom in
Previous page
1/20
Next page
9
Seal the ends of the tubes of the rack table using the rectangular plugs
60 x 30 [mm].
Inserting the plugs
Now mount the U-shaped bracket. To do this, insert four lock screws M6 x 70
from the inside, through the frame of the rack table and, from the outside,
place the U-shaped bracket onto the screws. Secure the U-shaped bracket
using washers and knurled nuts.
5.1.2 MOUNTING THE USHAPED BRACKET
To mount the rear lights,  rst place these in the protective moulds. Make
sure that the cable is  tted cleanly into the duct and is not crushed. The
rear lights with the reverse light is mounted on the right (in the direction of
travel) and the fog light is mounted on the left, in doing so, the openings for
license plate illumination for both lights must be on the inside. Now insert
the threaded bolts of the rear lights through the drilled holes in the rack
table and screw into place using washer and M5 nuts.
Mount the license plate holder using the already mounted screws and
washers to the rack traverse in such a way that the lamps and the license
plate holder are level. The mounting clips for securing the license plate are
push-out parts in the holder. Break out two of the clips. Slide the license
plate into the holder, then push the clips into the cut-outs to secure the
license plate.
5.1.6 MOUNTING THE WHEEL STOPPERS
Now push a wheel stopper on from above onto each of the wheel rails. Make
sure that the higher side of the wedge shape points towards the middle
of the rack. Insert a small tensioning strap through the middle opening of
each of the stoppers and under the wheel rail on the opposite side, then
back through the middle opening.
Tensioning strap 6 x
Stopper 4 x
5.1.7 MOUNTING THE FRAME HOLDER
Undo the handle screw of the frame holder and rotate out fully. Open the
cu of the frame holder and place the inserts around the U-shaped bracket
at a position suitable for your bicycle. Place the cu around the inserts and
push  rmly together. Close the frame holder using the handle screw (but
do not tighten).
Tighten the M16 screw slightly and align the bicycle rack parallel to the rear
of the vehicle. Now tighten the M16 screw in such a way to ensure that the
rack is securely attached and can no longer be rotated.
Regularly check the  rm seating of the rack on the trailer tow bar as well as
the functionality of the lighting systems.
5.2 MOUNTING THE BICYCLE RACK ON THE TRAILER TOW BAR
Make sure that the trailer tow bar is undamaged, clean and grease-free.
The bicycle rack is placed horizontally on the tow bar from above.
Slight signs of pressure on the tow bar ball are
normal and do not in uence the functionality.
M16 x 1.5 x 90 screw approximately one centimetre into the rack base.
Align all of the mounted parts and tighten all screw connections evenly and
rmly.
Knob nut M6
Lock screw M6 x 70
Washer 6 mm
U-shaped
bracket
Protective mould left Washer 5 mm
5.1.3 MOUNTING THE REAR LIGHTS
Rear light, left
Protective mould rightNut M5
Rear light, right
Reversing light
Cut-out for installation clips
5.1.5 MOUNTING THE LICENSE PLATE HOLDER/INSERTING THE
LICENSE PLATE
Cut-out for installation clips
5.1.4 LAYING THE ELECTRICAL CABLES
Lay the cables alongside the pipe of the rack table. The cables may not be
kinked, stretched nor squashed. Secure the cables with the supplied cable
ties. When you are  nished, trim any excess material from the cable ties
using cutting pliers.
Clips
… 9 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Eufab 11411 - Bike Two at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Eufab 11411 - Bike Two in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 1.25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info