72133
49
Zoom out
Zoom in
Previous page
1/54
Next page
General
In case of faults phone the service
department. See the guarantee certificate or
consult the internet site www.hps.nl.
If you notice a crack on the cooking
surface (no matter how little), switch
off the appliance immediately.
Remove the plug from the socket or set the
switch of the power supply cable (in the case
of a fixed connection) to zero or turn off the
fuse switch(es) in the meter cupboard.
Phone the service department.
This appliance should only be connected up
by a registered electrical installer!
The electrical connection must comply with
national and local regulations.
Damage caused by incorrect connection,
incorrect use or incorrect building in is not
covered by the guarantee.
96
97
FAULTS
Table
If the appliance does not work properly, this does not always mean that it is defective. Try to
deal with the problem yourself first by checking the points mentioned below:
You have observed the following: Possible causes: Solutions:
The display lights up. Normal operation. Do nothing, the display disappears
after 30 seconds.
Only works on one side.
The fuse in the meter cupboard is
defective.
Continuous beep.
The appliance is incorrectly
connected.
Check the electrical connection.
See electrical connection (page
100).
When first used a strange smell
comes from the hob.
New appliance. Warm a pan full of water for 30
minutes on each zone.
The hob does not work and the
displays on the operating panel
remain out.
The appliance is receiving no
power. Defective power supply or
incorrect connection.
Check the fuses and the electrical
master switch.
The hob does not work and an error
code F1, F2, F3 or F4 is displayed.
The electrical circuit works poorly. Contact the Service Department.
The hob does not work, the
information
or is
displayed.
The hob is locked. See chapter on use of child
protection.
The hob switches off during use, 4
dashes are displayed.
Something has boiled over or there
is an object on the operating panel.
Clean the hob or remove the object
and then continue cooking.
A series of small
or F0 is
displayed.
The electronic circuits are warm. See chapter on installation.
Error code F0 Pan is boiled dry or to hot. Let appliance cool down or continu
cooking on a lower setting.
After switching on a cooking
zone, the operating panel display
continues to flicker.
The pan you are using is not suitable
for induction cooking or has a
diameter of less than 12 cm (10 cm
for the 16 cm cooking zone).
See chapter on pans for induction
cooking.
Error code F5 or F6 Appliance overheated due to
insufficient ventilation.
Check the building-in situation or
contact the Service Department.
The pans are noisy during cooking.
Your cooking pan makes a ticking
sound during cooking.
Normal for certain types of pan.
It is caused by the energy being
transmitted from the hob to the pan
Do nothing. There is no danger for
the hob or for your pan.
The ventilator continues to work for
several minutes after the hob has
been switched off.
The electronics are cooling off.
Normal operation.
Nothing.
49


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna T 301 ZT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna T 301 ZT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 4,13 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Etna T 301 ZT

Etna T 301 ZT User Manual - English, German, Dutch, French - 54 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info