damage to the cooktop surface is prevented. Under no
circumstances use abrasive sponges or irritating chemi-
cal detergents such as oven sprays or stain removers.
USE
Use the touch control system in the corresponding
position relative to the individual cooking needs.
Keep in mind that the higher the number, the more heat
that it is produced.
FUNCTIONING
- On the basis of the model you own, the appliance can
be switched on by actuating the start-up sensor (Fig.4-
5-6-7-8 A). One zero will appear on all displays within10
seconds. If no display is actuated within 10 seconds, the
top will switch off again.
- Press selection key F for the desired cooking area.
A luminous "0" will appear on the respective display with
a decimal point to indicate which cooking area is active.
- A hotplate may be switched on by activating the "+" or
"-" sensor within 10 seconds. If sensor D is used, the
display will show selection 9, while if sensor C is used,
the display shows selection 1 or 5, depending on the
model.
- Once this operation has been performed choose the
temperature adjustment with the "+" or "-" keys.
- The plate can be switched off by selecting "0" with the
D sensor, after 3 seconds the cooking area is
automatically switched off.
It is always possible to switch a plate off by touching the
"+" and "-" sensors at the same time.
- The cooking top can be switched off by touching the
main start-up sensor (Fig.4-5-6-7-8 A). If all the plates
are selected on "0" the top will switch off after 10 seconds.
-If the top is equipped with plates with an extension (fig.5-
7-8) switching on of the second area will be carried out
after having checked that :
- the key button LED (fig.5-7-8 B) is off, otherwise de-
insert it.
- Press the key (fig.5-7-8 A) to switch the top on.
- Choose the desired plate and adjust the power using
the "+" or "-" keys.
-Once the power has been adjusted choose the key (fig.5-
7-8 L) to activate the double area.
- To deactivate the double area check that the interested
plate has been selected (fig.5-7-8 F) and press the key
(fig.5-7-8 L) .
Note: the Double area function is activated only on plates
F1 and F2 (fig.5-7-8 ).
- If an object is placed above the controls, the cooking
top will automatically move to the OFF position.
When a plate is in the OFF position and the temperature
is higher than 50° there will be a luminous signal "H"
near to the respective selection key (Fig.4- 5- 6-7-8 H).
- the B function blocks the functioning of the top on
selection.
E.g.: if the function is activated while the top has two
areas switched on the programme remains blocked even
if you try to switch another area on. The same thing
happens if the appliance is switched off and the function
is activated; the top doesn't switch on.
To activate or deactivate it hold a finger on the B sensor
for about two seconds. The function is active when
warning light E is switched on.
Heat up (Rapid heating)
The Heat up function can be used to set the cooking
zone to its maximum temperature for a specified period
of time, after which the temperature will return to a lower
value selected previously.
To activate the Heat up function, select the hotplate by
pressing the + button until setting 9 is displayed; if the
button is pressed again a decimal point "•" or the letter
"A" will appear on the display (next to the digit 9) for 5
seconds. This means the Heat up function is active.
The desired power level (between 1 and 8) should be
selected within 5 seconds. If power level 9 is selected,
the function is disabled. To deactivate the Heat up
function, simply select the + button and hold it down until
setting 9 is reached and the decimal point disappears
from the display. When the “Heat up” function is active,
the previously selected temperature level may be
increased b
y pressing the (+) button. Once the cooking
zone has reached the selected temperature, the “Heat
up” function is automatically deactivated and the hob
emits a BEEP. The cooking zone will operate in a constant
manner, at the set power level.
Timer (Fig.5).
- Select the plate with the relative power.
- Press the selection key again of the already-activated
plate.
- Using the "+" and "-" keys set the desired time.
- The decimal point at the side of the power level will
indicate that the plate has the TIMER function activated.
- An acoustic signal will indicate switching off of the
cooking area.
THE MANUFACTURER DECLINES ALL RESPONSI-
BILITY FOR EVENTUAL DAMAGES CAUSED BY
BREACHING THE ABOVE WARNINGS.
