692149
43
Zoom out
Zoom in
Previous page
1/92
Next page
EN 21
General
If you notice a crack in the glass top (however small), switch the hob off immediately, unplug
the hob or turn off the (automatic) fuse switch(es) in the meter cupboard or. In the event of a
permanent connection, set the switch in the power supply lead to zero. Contact the service
department.
Troubleshooting table
If the appliance does not work properly, this does not always mean that it is defective.
Try to deal with the problem yourself first by checking the points mentioned below or check for
more information the website ‘www.etna.nl’.
Symptom Possible cause Solution
The display lights up when
the hob is activated for the
first time.
This is the standard set-
up routine.
Normal operation.
The fan runs on for several
minutes after the hob has
been switched off.
The hob is cooling. Normal operation.
A slight smell is noticeable
the first few times the hob
is used.
The new appliance is
heating up.
This is normal and will
disappear once it has been
used a few times. Ventilate
the kitchen.
The pans make a noise while
cooking.
This is caused by the energy
flowing from the hob to the
saucepan.
At high settings this is
perfectly normal for some
pans. It will not damage either
the pans or the hob.
You have switched on
a cooking zone, but the
display shows ‘u’. Link
function (Bridge cooking
zones) doesn’t work.
The pan you are using is
not suitable for induction
cooking, or has a diameter
of less than 12 cm.
Use a suitable pan. Bridge
cooking zones have to be
fully covered by the pans.
A cooking zone suddenly
stops working and you hear
a signal.
The preset time has ended. Switch off the bleep by
touching the + key of the
timer.
The hob is not working
and nothing appears in
the display.
There is no power supply
due to a defective cable or
a faulty connection.
Check the fuses or the electric
switch (if there is no plug).
A fuse blows as soon as the
hob is switched on.
The hob has been wrongly
connected.
Have the electrical
connection checked.
TROUBLESHOOTING
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna KI278ZT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna KI278ZT in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 6,96 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Etna KI278ZT

Etna KI278ZT Installation Guide - English, German, Dutch, French - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info