Manual Etna EN4500 (page 14 of 20) (English, German, Dutch, French, Italian)

2872

Zoom out

Zoom in

1/20

- 14 -

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to

cooking.

It is recommended to leave the appliance in operation for

15 minutes after cooking is terminated in order to com-

pletely eliminate cooking vapours and odours.

The proper function of the cooker hood is conditioned by

the regularity of the maintenance operations, in particu-

lar, the active carbon filter.

• The anti-grease filters capture the grease particles

suspended in the air, and are therefore subject to clog-

ging according to the frequency of the use of the appli-

ance.

In order to prevent fire hazard, it is recommendable to

clean the filter at a maximum of 2 months by carrying out

the following instructions:

- Remove the filters from the cooker hood and wash them

in a solution of water and neutral liquid detergent, leaving

to soak.

- Rinse thoroughly with warm water and leave to dry.

- The filters may also be washed in the dishwasher.

The aluminium panels may alter in colour after several

washes. This is not cause for customer complaint nor

replacement of panels.

• The active carbon filters purify the air that is replaced

in the environment. The filters are not washable nor re-

useable and must be replaced at maximum every four

months. The saturation of the active carbon filter de-

pends on the frequency of use of the appliance, by the

type of cooking and the regularity of cleaning the anti-

grease filters.

• Clean the fan and other surfaces of the cooker hood

regularly using a cloth moistened with denatured alcohol

or non abrasive liquid detergent.

• The illumination installation is designed for use during

cooking and not for prolonged general illumination of the

environment. Prolonged use of the illumination installa-

tion notably reduces the duration of the bulb.

COMMANDS: (Fig.11)

Push-button A = on/off lights switch

Push-button B = on/off cooker hood switch. The appli-

ance switches on at speed level 1, If the cooker hood is

on depress the push-button for ½ a second to switch off

the cooker hood. If the cooker hood is at speed level 1

it will not be necessary to depress the push-button to

switch the cooker hood off. Decreases the motor speed.

Display C = indicates the motor speed level selected and

activates the timer.

Push-button D = switches on the cooker hood. Increases

the motor speed. Touching the key at 3rd speed, the

intensive function runs for 10', then the appliance go

back to work at the original speed. During this function

the display blinks.

Push-button E = Timer, when active should be visible via

the decimal point flashing in the Display “C”. Depressing

the push-button when the cooker hood is in the off mode

will switch on the appliance at the first speed level for 15’

[minutes]. The Timer switches the cooker hood off com-

pletely (lamps and motor) after 15’ [minutes].

E.g.: if the lamps only switch on, and the timer switch is

depressed then the lamp will turn off after 15’ [minutes].

To deactivate the timer depress the push-button a sec-

ond time (twice).

The "Automatic stop timer" delays stopping of the hood,

which will continue functioning for 15 minutes at the

operating speed set at the time this function is activated.

• CONTROLS: ELECTRONIC (fig.10)

A = LIGHT

B = OFF/SPEED I

C = SPEED II

D = SPEED III

E = AUTOMATIC STOP TIMER – 15 minutes

F = FILTER SATURATION RESET LIGHT

When the “filter saturation” light flashes, the anti-grease

filters must be washed.

When the light comes on without flashing, the anti-grease

filters must be washed and the carbon filters replaced (in

case of operation whit the recycling version).

When this operation has been completed, press the key

to reset it.

• COMMANDS: (Fig.9A) LUMINOUS the key symbols are

explained below:

A = LIGHT

= OFF

C = SPEED I

D = SPEED II

E = SPEED III

F = AUTOMATIC STOP TIMER - 15 minutes

• If your appliance does have the INTENSIVE speed

function, press key E for two seconds and it will be

activated for 10 minutes after which it will return to the

previously set speed.

When the function is active the LED flashes. To inter-

rupt it before the 10 minutes have expired press key E

again.

• By pressing key F for two seconds (with the hood

switched off) the “clean air” function is activated. This

function switches the appliance on for ten minutes every

hour at the first speed. As soon as this function is acti-

vated the motor starts up at the first speed for ten

minutes, During this time key F and key C must flash at

the same time.

After ten minutes the motor switches off and the LED of

key F remains switched on with a fixed light until the

motor starts up again at the first speed after fifty min-

utes and keys F and C start to flash again for ten minutes

and so on.

By pressing any key for the exclusion of the hood light

the hood will return immediately to its normal functioning

(e.g. if key D is pressed the “clean air” function is deac-

tivated and the motor moves to the 2nd speed straight

away. By pressing key B the function is deactivated).

• The “automatic stop timer” delays stopping of the

hood, which will continue functioning for 15 minutes at

the operating speed set at the time this function is

activated.

• COMMANDS:(Fig.9 B)MECHANICAL_ the key symbols

are explained below:

A = LIGHT

B = OFF

C = SPEED I

D = SPEED II

E = SPEED III

G = MOTOR WORKING indicator

THE MANUFACTURER DECLINES ALL RESPONSIBILITY

FOR EVENTUAL DAMAGES CAUSED BY BREACHING

THE ABOVE WARNINGS.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna EN4500 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 0,33 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna EN4500 Manual

Product: