Manual Etna a4453t (page 22 of 29) (English, German, Dutch, French, Italian, Portuguese, Spanish)

132684

Zoom out

Zoom in

1/29

If the appliance is connected directly to the electricity supply,

an omnipolar switch with a minimum contact opening of

3 mm must be placed in between the two; its size must

be suitable for the load required and it must comply with

current legislation.

• If the hob is electric, gas, or induction, the minimum distance

between the same and the lower part of the hood must be

at least 65 cm.

If a connection tube composed of two parts is used, the upper

part must be placed outside the lower part.

Do not connect the cooker hood exhaust to the same conduc-

tor used to circulate hot air or for evacuating fumes from other

appliances generated by other than an electrical source.

Before proceeding with the assembly operations, remove

the anti-grease  lter(s) (Fig.16) so that the unit is easier to

handle.

In the case of assembly of the appliance in the suction version

prepare the hole for evacuation of the air.

• We recommend the use of an air exhaust pipe with a

diameter of 150. If a pipe with a smaller diameter is used, the

e ciency of the product may be reduced and its operation

may become noisier

• Hood assembly

Remove the structure from the packaging and remove the

2 screws A to separate the upper part from the lower part

(Fig.2).

- Position hole template on the ceiling paying attention that

the arrow is positioned on the same side as the appliance

controls (Fig.3).

Make 4, Ø8 holes in the ceiling and drive in 3 screws without

completely tightening them. Pay attention not to insert the

screw into the hole marked with an X on the hole template

(the screws and expansion plugs must be suitable for the

type of wall).

- Take the upper part of the structure B (Fig.4) and insert the 3

slots onto the 3 screws that are not completely tightened.

Rotate slightly to  t (Fig.4) .

Drive in the fourth screw X and tighten the remaining 3 to

allow de nitive blocking of the upper part of structure B

- Take the lower part of the telescopic structure C and insert

it into the upper structure B (Fig.5).

Adjust the height by referring to the amounts indicated in

(Fig.15) and block it using the 8 screws G that are supplied

(Fig.6).

• Suction version:  x the  exible pipe to the prepared air

evacuation hole (Fig 7).

• Filtering version: We have two different types of Kit, one

with extractable carbon filters (Fig.18) and the other one with

re-usable carbon filters (washable). (Fig.19)

If you find a bracket such as the one indicated in Fig.20

included in the product packaging, this should be fixed to

the hood using the supplied screws.

- Fix the  exible pipe to the de ector M and  x screw I as

indicated in (Fig.8), the active carbon  lters must be applied

to the suction unit positioned inside the hood (Fig.18).

- If your product is 

ed with a connector  ange, perform

the assembly steps indicated in  g. 9 before  xing the cooker

hood to the structure.

Take connector  ange F and  t it to the upper part of the

cooker hood suction assembly using the 2 screws E (Fig. 9).

- Take the upper chimney piece and  x it to the structure using

the 2 screws A (Fig.10).

Join the lower chimney piece with the upper one and  x it

carefully using adhesive tape L (Fig.11a).

- Unscrew the 2 screws O, max 3 mm (Fig.11a).

Insert the suction unit inside the structure paying attention

that the previously unscrewed screws O, hook into the slots

in the lower part as indicated in (Fig.11b).

Drive in the 3 screws N (supplied) and tighten the 2 screws

O (Fig.11b).

- Fix the air evacuation pipe H (not supplied) onto the con-

nection  ange F (Fig.12)

- Remove adhesive tape L and rest the lower chimney piece

above the cooker hood (Fig.13).

-If the cooker hood is supplied with a lower chimney piece

that must be  xed to the hood body with screws, remove the

anti-grease  lters from the hood by acting on the relevant

handles (Fig.16).

- If necessary,  x the lower duct to the hood from the inside,

using the screws P (Fig. 14).

Re-locate the  lters in their seat.

USE AND MAINTENANCE

• We recommend that the cooker hood is switched on before

any food is cooked.

We also recommend that the appliance is left running for

15 minutes after the food is cooked, in order to thoroughly

eliminate all contaminated air.

The e ective performance of the cooker hood depends on

constant maintenance; the anti-grease  lter and the active

carbon  lter both require special attention.

• The anti-grease  lter is used to trap any grease particles

suspended in the air, therefore is subject to saturation (the

time it takes for the  lter to become saturated depends on

the way in which the appliance is used).

- To prevent potential  re hazards, the anti-grease  lters should

be washed a minimum of every 2 months (it is possible to use

the dishwasher for this task).

- After a few washes, the colour of the  lters may change. This

does not mean they have to be replaced.

If the replacement and washing instructions are not followed,

the anti-grease  lters may present a  re hazard.

• The active carbon  lters are used to purify the air which is

released back into the room.

The  lters are not washable or re-usable and must be replaced

at least once every four months.

The active carbon  lter saturation level depends on the fre-

quency with which the appliance is used, the type of cooking

performed and the regularity with which the anti-grease

 lters are cleaned.

• Clean the cooker hood frequently, both inside and outside,

using a cloth which has been dampened with denatured

alcohol or neutral, non-abrasive liquid detergents.

• The light on the cooker hood is designed for use during

cooking and not for general room illumination.

Extended use of the light reduces the average duration of

the bulb.

• Replacing halogen light bulbs (Fig. 17).

To replace the halogen light bulbs B, remove the glass pane

C using a lever action on the relevant cracks.

Replace the bulbs with new ones of the same type.

Caution: do not touch the light bulb with bare hands.

• Replacing halogen light bulbs (Fig. 18).

In order to replace the dichroic lamps, carefully remove

the lamp from the lamp holder with the help of a small  at

screwdriver or a similar tool.

PLEASE NOTE! In doing this operation, please take care

- 23 -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna a4453t in the language / languages: English, German, Dutch, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,78 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna a4453t Manual

Product: