406152
43
Zoom out
Zoom in
Previous page
1/46
Next page
YOUR COFFEEPADMACHINE
7 Faults
GB 19
CAUSE SOLUTION
ere comes less or no coffee at
all out of the coffeeoutlet.
Remove the cremamaker by pushing it out, from below,
with a blunt object like a pen or the back of a teaspoon
and rinse it with warm water. One grain of coffee can
cause it to be blocked.
Check if the coffee-outlet is clogged and if necessary
clean it.
Check the position of the taste-selector.
We advise to loosen the coffee in the coffeepads before
you place them in the machine. is will ensure a
better transit of the water and will give a finer layer of
coffeecrema.
Coffeepaddrawer wont open
(vacuum).
You can solve the vacuum yourself by decompressing the
appliance using the valve inside the small hole on the
appliance (see “I” on page 5).
Procedure: Make sure that the waterreservoir is placed in
the appliance. Put a thin, blunt object inside the hole to
activate the valve. Keep pressing it during several seconds
until the water stops flowing back into the waterreservoir
and both pilot lamps (red and green) light up constantly.
Careful: the water that is being pumped back, is hot.
You have succesfully decompressed the appliance.
After you can open the coffeepaddrawer again, you must
clean the cremamaker and the multi-padholder. If
you do not clean the parts, the cause of the vacuum will
not be solved and at re-use the appliance will get locked
again.
Cleaning the cremamaker: Remove the cremamaker by
pushing it out, from below, with a blunt object like a pen
or the back of a teaspoon and rinse it with warm water.
One grain of coffee can cause it to be blocked.
YOUR COFFEEPADMACHINE
7 Faults
GB 18
CAUSE SOLUTION
e lock does not work - the pilot
lamp keeps blinking.
Check if the coffeepad(s) has (have) been placed
correctly.
Coffeepaddrawer is not locked, open the drawer and lock
it again.
Check the multi-padholder - at the back there should be
a protrusion sticking out, when this has broken off the
machine is not able to make coffee. Order a new multi-
padholder at an authorised technical service centre.
43


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna a2793 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna a2793 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info