336797

Etna a 566 Manual

15
Zoom out
Zoom in
Previous page
1/40
Next page
15
Position the clips as shown in the diagram,
fastening them to the openings in the lower
part of the body using the screws provided.
For worktop thicknesses of 30 mm. or less,
use the self-tapping screws that are provi-
ded as a fastening accessory - put them
into the clip’s round hole. This hole will be
threaded as the screw is inserted into it,
and this should be done before fixing the
clip to the worktop.
Connecting the electricity
Before connecting the hob to the electric
mains, check that the voltage and fre-
quency of the mains matches what is
shown on the hob’s rating plate, which is
located lower down, and on the guarantee
certificate or, where appropriate, the tech-
nical datasheet supplied, which should be
kept together with this manual.
The electric connection is made via an
omnipolar switch or plug where accessi-
ble, which is suitable for the intensity to be
tolerated and which has a minimum gap of
3 mm between its contacts, which will
ensure disconnection in case of emer-
gency or when cleaning the hob.
The connection should include correct ear-
thing, in compliance with current norms.
Avoid that the cabling remain in contact
with neither the casing of the hotplate nor
that of the oven.
Joining the hob to the oven
1 Disconnect the electricity.
2 Partially place the oven in its position.
3 Plug in the connection(s) between the
cooker and the oven (see fig. 3) to con-
nect both appliances. Make sure the
connectors fit completely in its soc-
kets and the intersection haven’t cau-
sed the exit of any of the terminals.
To check this, pull slightly the cables,
one by one, making sure they have all
kept in.
4 Finish inserting the oven into its definiti-
ve position.
Rear view of the A6405 oven:
The instruction manual indicates
how the oven must be positioned as well as
how the electrical connectors must be set
up. Before accessing the interior of the
appliance, it must be disconnected from the
power outlet.
40 mm
20/30 mm
fig. 2
Self-tapping screw for 20
and 30 mm thick worktops
Sealing joint
Sealing joint
GB
fig. 3
… 15 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna a 566 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna a 566 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info