Manual Etna A 4461 T (page 12 of 17) (English, German, Dutch, French, Italian, Polish, Spanish)

109790

Zoom out

Zoom in

1/17

- 14 -

GENERAL

Carefully read the following important information regarding installa-

tion safety and maintenance. Keep this information booklet accessible

for further consultations. The appliance has been designed for use in

the ducting version (air exhaust to the outside – Fig.1B), filtering ver-

sion (air circulation on the inside – Fig.1A) or with external motor

(Fig.1C).

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an

open fireplace or burner that depend on the air in the environment and

are supplied by other than electrical energy, as the cooker hood re-

moves the air from the environment which a burner or fireplace need

for combustion. The negative pressure in the environment must not

exceed 4Pa (4x10-5 bar). Provide adequate ventilation in the environ-

ment for a safe operation of the cooker hood. Follow the local laws

applicable for external air evacuation.

Before connecting the model to the electricity network:

- control the data plate (positioned inside the appliance) to ascertain

that the voltage and power correspond to the network and the socket is

suitable. If in doubt ask a qualified electrician.

- If the power supply cable is damaged, it must be replaced with another

cable or a special assembly, which may be obtained direct from the

manufacturer or from the Technical Assistance Centre.

2. WARNING !

In certain circumstances electrical appliances may be a danger

hazard.

A) Do not check the status of the filters while the cooker hood

is operating

B) Do not touch bulbs or adjacent areas, during or straight after

prolonged use of the lighting installation.

C) Flambè cooking is prohibited underneath the cooker hood

D) Avoid free flame, as it is damaging for the filters and a fire

hazard

E) Constantly check food frying to avoid that the overheated

oil may become a fire hazard

F) Disconnect the electrical plug prior to any maintenance.

G) This appliance is not intended for use by young children or

infirm persons without supervision

H) Young children should be supervised to ensure they do not

play with the appliance

I) There shall be adequate ventilation of the room when the

rangehood is used at the same time as appliances burning gas

or other fuels

L) There is a risk of fire if cleaning is not carried out in accord-

ance with the instructions

This appliance conforms to the European Directive EC/2002/96, Waste

Electrical and Electronic Equipment (WEEE). By making sure that

this appliance is disposed of in a suitable manner, the user is helping

to prevent potential damage to the environment or to public health.

The

symbol on the product or on the accompanying paperwork

indicates that the appliance should not be treated as domestic waste,

but should be delivered to a suitable electric and electronic appliance

recycling collection point. Follow local guidelines when disposing of

waste. For more information on the treatment, re-use and recycling of

this product, please contact your local authority, domestic waste

collection service or the shop where the appliance was purchased.

INSTALLATION INSTRUCTIONS

Assembly and electrical connections must be carried out by

specialised personnel.

• Electric Connection

The appliance has been manufactured as a class II, therefore no earth

cable is necessary.

The connection to the mains is carried out as follows:

BROWN = L line

BLUE = N neutral

If not provided, connect a plug for the electrical load indicated on the

description label. Where a plug is provided, the cooker hood must be

installed in order that the plug is easily accessible.

An omnipolar switch with a minimum opening of 3mm between con-

tacts, in line with the electrical load and local standards, must be placed

between the appliance and the network in the case of direct connection

to the electrical network.

• The minimum distance between the support surfaces of the cooking

pots on the cooker top and the lowest part of the cooker hood must be

at least 65 cm. If a connection tube composed of two parts is used, the

upper part must be placed outside the lower part. Do not connect the

cooker hood exhaust to the same conductor used to circulate hot air or

for evacuating fumes from other appliances generated by other than an

electrical source.Before proceeding with the assembly operations, re-

move the anti-grease filter(s) (Fig.7) so that the unit is easier to handle.

In the case of assembly of the appliance in the suction version prepare

the hole for evacuation of the air.

• FIXING TO THE WALL

Drill the holes A respecting the distances indicated (Fig.2). Fix the

appliance to the wall and align it in horizontal position to the wall units.

When the appliance has been adjusted, definitely fix the hood using the

screws A (Fig.5). For the various installations use screws and screw

anchors suited to the type of wall (e.g. reinforced concrete, plaster-

board, etc.). If the screws and screw anchors are provided with the

product, check that they are suitable for the type of wall on which the

hood is to be fixed.

• FIXING THE DECORATIVE TELESCOPIC FLUE

Arrange the electrical power supply within the dimensions of the deco-

rative flue. If your appliance is to be installed in the ducting version or

in the version with external motor, prepare the air exhaust opening.

Adjust the width of the support bracket of the upper flue (Fig.3). Then

fix it to the ceiling using the screws A (Fig.3) in such a way that it is in

line with your hood and respecting the distance from the ceiling indi-

cated in Fig.2. Connect the flange C to the air exhaust hole using a

connection pipe (Fig.5).

Insert the upper flue into the lower flue. Fix the lower flue to the hood

using the screws B provided (Fig.5), extract the upper flue up to the

bracket and fix it with the screws B (Fig.3).

If your appliance has the lower connections indicated as in Fig. 4 A, the

fixing to be carried out is that shown in Fig. 6 A

To transform the hood from a ducting version into a filtering version,

ask your dealer for the charcoal filters and follow the installation in-

structions.

• FILTERING VERSION

Install the hood and the two flues as described in the paragraph for

installation of the hood in ducting version. To assemble the filtering flue

refer to the instructions contained in the kit. If the kit is not provided,

order it from your dealer as accessory. The charcoal filters must be

fitted in the ducting unit located inside the hood (Fig.8).

USE AND MAINTENANCE

• It is recommended to operate the appliance prior to cooking.

It is recommended to leave the appliance in operation for 15 minutes

after cooking is terminated in order to completely eliminate cooking

vapours and odours.

The proper function of the cooker hood is conditioned by the regularity

of the maintenance operations, in particular, the active carbon filter.

ENGLISH

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna A 4461 T in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 0,29 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna A 4461 T Manual

Product: