336796

Etna a 361 k Manual

47
Zoom out
Zoom in
Previous page
1/50
Next page
93
INSTALLATION
The voltage between the phases and the
neutral is 230 V a.c. Between the lives there is
a voltage of 400 V. If there is not a voltage
of 400 V between the lives, two wires have
been taken from the same live in the meter
cupboard and the hob must be connected
with two neutral wires, as indicated above
under 2 lives with 2 neutrals. Install a
connecting bridge between the connection points
3-4. Your groups must be fused with at least
16 A (2x). The connecting power cable must have
a minimum core cross section of 2,5 mm
2
.
Special connections
1 phase connection (1 1N a.c. 230 V / 50 Hz):
The voltage between live and neutral is 230 V a.c.
Install connecting bridges between connection
points 1-2 and 3-4. Your group must be protected
by a fuse of at least 32 A. The connecting power
cable must have a minimum core cross section of
6 mm
2
.
3-phase connection (3 a.c. 230 V / 50 Hz):
The voltage between the phases and the neutral is
230 V a.c. Install connecting bridges between the
connection points 3-4. Your groups must be fused
with at least 16 A (3x). The connecting power
cable must have a minimum core cross section of
2,5 mm
2
.
You can use the bridges provided on the
connecting block to make the required
interconnections as indicated in the preceding
illustrations.
Safety prescriptions
For the appliance to work well, it is important:
n That there is sufficient ventilation to allow
the hob to cool down, in accordance with the
possibilities specified in this chapter.
n The ventilation air drawn in by the hob must
not be warmer than 35 °C. Bear this in mind if
the oven is to be built in under the hob.
n That the connecting cable hangs freely and is
not caught by a drawer.
n The worktop should be a minimum of 2.8 cm
and a maximum of 5 cm thick.
n The worktop is flat.
Power table
The appliance can be connected in the
following ways:
Common connections
2 lives with 2 neutrals connection
(2 2N a.c. 230 V / 50 Hz):
The voltage between live and neutral is 230 V
a.c. There may be a voltage of 0 V between the
phases if they are connected to the same phase
in the meter cupboard but also 400 V if they are
connected to 2 different phases.
Your groups must be fused with at least 16 A (2x).
The connecting power cable must have a minimum
core cross section of 2,5 mm
2
.
3 lives with 1 neutral connection
(3 1N a.c. 400 V / 50 Hz):
The voltage between the phases and the neutral
is 230 V a.c. There is a voltage of 400 V between
the lives. Fit a connecting bridge between the
connection points 3-4. Phase 3 carries no load.
Your groups must be fused with at least 16 A (3x).
The connecting power cable must have a minimum
core cross section of 2,5 mm
2
.
2 lives with 1 neutral connection
(2 1N a.c. 400 V / 50 Hz):
92
INSTALLATION
Type of hob A361KZT
Induction x
Electrical connection
230 V - 50 Hz x
Maximum power cooking
zones
Front left 2300 W contin.
Rear left 1400 W contin
Rear right 2300 W contin
Front right 1400 W contin
Power connection
L1 3700 W
L2 3700 W
Total power connection
7400 W
43 21
2N a.c. 230V / 50 Hz
generators
right
appliance
internal
generators left
43 21
1N a.c. 400V / 50 Hz
appliance
internal
generators
right
generators left
43 21
3N a.c. 400 V / 50 Hz
appliance
internal
generators
right
generators left
43 21
1N a.c. 230V / 50 Hz
appliance
internal
generators
right
generators left
43 21
3 a.c. 230V / 50 Hz
appliance
internal
generators
right
generators left
… 47 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna a 361 k at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna a 361 k in the language / languages: Dutch as an attachment in your email.

The manual is 3,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info