Manual Etna 1989 (page 9 of 21) (English, German, Dutch, French)

324581

Zoom out

Zoom in

1/21

GEBRUIK VAN DE GASGRILL

Fig. 7

Fig. 8

Fig. 9

Fig. 10

Fig. B

RL F

Fig. 11

Fig. 12

140

210

170

250

Fig. A

TAB. C

GERECHT TEMP. °C GERECHT TEMP. °C

VLEES GEBAK

VARKENSGEBRAAD 185-210 FRUITTAART 220

RUNDGEBRAAD 250 CAKE 190

OSSEGEBRAAD 240 BRIOCHES 175

KALFSGEBRAAD 220 BISCUITDEEG 235

LAMSGEBRAAD 220 KOEKJES 190

ROAST-BEEF 230

ZOET BLADERDEEGGEBAK 200

HAAS 235 ROZIJNENGEBAK 200

KONIJN 220 STRUDEL 180

KALKOEN 235 LANGE VINGERS 290

GANS 225 APPELFLAPPEN 200

EEND 235

PUDDING VAN LANGE VINGERS 200

KIP 200-225 TOAST 250

VIS 200-225 BROOD 230

10 35

BRANDER MET VEILIGHEIDSTHERMOKOPPEL

Bij branders die voorzien zijn van een veiligheidsthermokoppel,

moet u de knop na inschakeling van de brander nog ongeveer 10

seconden vast blijven houden (fig.9), zodat de veiligheidsklep in

werking treedt. Als de vlam dooft nadat u de knop heeft losgelaten,

bovenbeschreven handelingen herhalen.

Gebruik van de oven

De oven voor gebruik voorverwarmen op de gewenste temperatuur.

Nadat de gewenste temperatuur bereikt is, de gerechten in de

oven zetten en de baktemperatuur controleren. Zet de oven 5

minuten voor het verstrijken van de bereidingstijd uit om de

restwarmte te gebruiken. Hieronder volgt een lijst met indicatieve

bereidingstijden van verschillende gerechten (tabel C).

LET OP: de inschakelknop niet langer dan 15 seconden

vasthouden.

Als de brander van de oven niet aangaat, de ovendeur tenminste

1 minuut open laten staan voordat u de knop opnieuw indrukt.

Elektrische inschakeling

Om de grillbrander in te schakelen, de knop indrukken en tegen

de klok in op de stand (Fig. 7) zetten; tegelijkertijd op de

elektrische inschakelknop op het paneel (aangegeven met het

symbool ) drukken.

Als er geen elektrische stroom is, kan de brander ook worden

aangestoken met een lucifer (fig. 10).

BRANDER MET VEILIGHEIDSTHERMOKOPPEL

Bij branders die voorzien zijn van een veiligheidsthermokoppel

moet u de knop na inschakeling van de brander nog ongeveer 10

seconden vast blijven houden (fig.9), zodat de veiligheidsklep in

werking treedt. Als de vlam dooft nadat u de knop heeft losgelaten,

bovenbeschreven handelingen herhalen.

- Plaats de knoppenbescherming S en laat de deur halfopen

(zie fig. A).

LET OP :

De grill moet worden gebruikt met half geopende deur .

Plaats de knoppenbescherming S en laat de deur halfopen

(zie fig. A).

Braadspit - ( Mod. 1920 ).

Voor het gebruik van het draaispit, als volgt te werk gaan:

- Steek de kip of het te roosteren gedeelte op het spit L en zet

het stevig en goed uitgebalanceerd vast tussen de twee vorkjes

F, om een onnodige overbelasting van de reductor R (fig. 11)

te vermijden.

- Plaats het spit op support G, na het andere uiteinde ervan in

het gat P van het motortje R (fig. 11) te hebben gestoken.

Plaats support G volledig in de oven, om de spies I in het gat

H van motor M van het braadspit te laten vallen (Fig. 12).

- Zet de druippan met een beetje water erin onder het spit.

- Draai de knop op symbool (fig. B)

- Om het spit te verwijderen moet u andersom te werk gaan en

knop A en een handschoen van isolerende wol gebruiken

(Fig 13).

GAS CONNECTION

Fig. 2

1/2

Applance type Supply single-phase 230 V~

Type of cable section

All gas + elett. oven Rubber H05 RR-F

Applance type Supply single-phase 230 V~

Type of cable section

All gas + gas oven Rubber H05 RR-F

The appliance must be connected to the gas piping in a workmanlike

way and in conformity with the regulations in force which lay down

the installation of a safety valve at the end of the piping.

For butane and propane a pressure reducer conforming to the

standards in force may perform this task.

The seal gaskets must be in accordance with rules.

Once the gas appliance has been connected, check the connection

seal by means of soapy water.

The end of the attachment is threaded.

The possible connections are:

We recommend to check wether the appliance has been foreseen

for the kind of gas distributed.

- by rigid pipe in iron or copper

- by flexible tube in stainless steel with continuing wall, with

mechanical connection in accordance with rules. The tube must

be directly connected to the manifold elbow (see Fig.2).

- by the insertion of a rubber tube in accordance with rules.

This tube must be connected directly on the push-on connector,

concerning the gas used, and it must be blocked with a band.

In the last case, check the tube's printed date of expiry and

replace it before this date.

STOP

INLET

Certain types of cookers can be set for sypply both on the right

and

lefthand side. In this case it is sufficient to reverse the position

of the cad nipple reducer. At the end make sure than there is no

leakage of gas.

ELECTRICAL CONNECTION

REPLACEMENT OF THE CABLE

In case the cable is damaged, replace it in accordance with the

following instructions:

- open the box of the supply board as described on the picture

below;

- unscrew screw A fixing the cable;

- replace the cable with one of the same lenght and in accordance

with the features described on the table; switch the appliance

off, and close the gas tap

- the green-yellow earth wire must be connected to the terminal

  and it must be about 10 mm longer thean the live wires;

- the blue neutral wire must be connected to the terminal marked

with letter N;

- the live wire must be connected to the terminal marked with letter

L.

This appliance must be earthed by law. Before connecting

the

appliance to the electrical supply, check that the earth

system in your house is working correctly.

Check that unit voltage and power, marked on the rating plate

applied on the appliance, are correct for the supply. It is necessary

that the feeding network is protected by a powerful switch able to

disconnect completely the network with a contacts separation of

at least 3 mm. Be sure that the earth wire green/yellow is not

interrupted by the switch.

Important: The wires in the mains lead are so coloured:

- green/yellow = earth " "

- blue = neutral N

- brown = live L

The wire coloured green/yellow must be connected to the terminal

in the plug which is marked with letter 'E' or by the earth symbol

or coloured green or green/yellow. The wire coloured blue must

be connected to the terminal which is marked with letter 'N' or

coloured black. The wire coloured brown must be connected to

the terminal which is marked with letter 'L' or coloured red. The

supply cable must not come into contact with any component the

temperature of which exceeds the ambient temperature by 50°C.

If a plug is used for connection, the plug to be connected to the

supply cable and the socket to which it is connected must be of

Connection of the appliance to the power mains should be done

by a licensed electrician familiar with local safety regulations.

3 x 1,5 mm

the same type (conforming to the standards). Easy access to the

plug or the switch is ensured once the appliance is installed. Ensure

that there is sufficient cable allowed for any subsequent removal

of the unit. If the plug is non-rewireable, pay attention to the

following points: the plug must never be cut by the supply cord.

There is shock hazard when this plug is inserted in a socket-outlet

elsewhere in the house. Never use the plug without the fuse cover

fitted. Referring to the pertinent spare parts, apply to the appliance's

supplier.

3 x 0,75 mm

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna 1989 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,83 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna 1989 Manual

Product: