Manual Etna 1631H (page 38 of 48) (English, German, Dutch, French)

2740

Zoom out

Zoom in

1/48

INSTALLATION

The appliance must be installed by qualified

staff working in accordance with the regula-

tions in force.

Before installing, ensure that the appliance

is correctly preset for the local distribution

conditions (gas type and pressure).

The presettings of this appliance are indi-

cated on the nameplate shown on the cover.

This appliance is not connected to a flue gas

extractor device. It must be installed and

connected in accordance with the regulations

in force.

This appliance may only be installed and may

only operate in rooms permanently ventilated

in accordance with national regulations in

force.

VENTILATION

The rooms in which gas appliances are in-

stalled must be well ventilated in order to al-

low correct gas combustion and ventilation.

The air flow necessary for combustion is at

least 2 m

/h for each kW of rated power.

POSITIONING

Remove the packaging accessories, includ-

ing the films covering the chrome-plated and

stainless steel parts, from the cooker.

Position the cooker in a dry, convenient and

draft-free place. Keep at an appropriate dis-

tance from walls which may be damaged by

heat (wood, linoleum, paper, etc.).

The cooker may be free-standing (class 1)

or between two units (in class 2 st 2-1) the

sides of which must withstand a temperatu-

re of 100°C and which must not be higher

than the working table.

CONNECTING TO THE GAS SUPPLY

Before connecting the cooker, check that it

is preset for the gas to be used.

The connection is on the right; if the pipe has

to pass behind the cooker, it must be kept low

down where the temperature is about 50°C.

- Rigid connection (see fig. 3 A and B)

The connection to the mains gas supply

may be made using a rigid metal pipe or

with a metal hose. Remove the hose

connector (if already fitted) and screw the

rigid union onto the threaded connection

of the gas train (see fig. 3 A). The union for

rigid connection may already be fitted on

the gas train, or may be amongst the cooker

accessories. Otherwise, it can be obtained

from your dealer.

If national regulations permit, a metal hose

complying with the national standards can

be screwed directly onto the threaded

connection of the gas train, fitting a seal

(see fig. 3B).

However, users are strongly recommended

always to fit the rigid union.

- Connection using a rubber hose (see fig.

3 C and D)

Connect a rubber hose carrying the

conformity mark currently in force to the hose

connector. The hose must be replaced at

the date indicated at the latest, and must

be secured at both ends using standard

hose clamps. It must be absolutely

accessible to allow its condition to be

checked along its entire length.

CAUTION:

- Use of the hose connector is only

permitted for free-standing installation.

If the appliance is installed between two

class 2 st. 2-1 unions, the rigid union is

the only form of connection permitted.

IMPORTANT:

- After installation, check that the

connections are airtight.

- Use only standard rubber hoses.

- Avoid sharp bends in the pipe and keep it

well way from hot surfaces.

- References to the regulations covering the

gas connection to the appliance: ISO 7-1

(NL)

CONNECTING TO THE ELECTRICAL

MAINS

Before making the connection, check that:

- the mains voltage is as indicated on the

nameplate;

Installation

334821/01 20-11-2001, 17:1838

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Etna 1631H in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,47 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Etna 1631H Manual

Product: