324297

Etna 1553wt Manual

39
Zoom out
Zoom in
Previous page
1/48
Next page
39
- the earth connection is in good working or-
der.
If the socket is not easily accessible, the in-
stallation engineer must provide a switch with
a contact breaking gap of 3 mm or more.
If the appliance power lead is not fitted with
a plug, use an approved standard type, re-
membering that:
- the green-yellow wire must be used for the
earth connection;
- the blue wire is the neutral;
- the brown wire is live;
- the lead must never touch hot surfaces over
about 75 degrees C;
- replacement leads must be of type H05RR-
F or H05V2V2-F of suitable size (see dia-
grams in fig. 2).
- if the appliance is supplied without lead,
using type H05RR-F or H05V2V2-F cable
of suitable size (see diagrams in fig. 2).
IMPORTANT: the manufacturer declines all
liability for damage due to failure to comply
with the regulations and standards in force.
Check that the appliance is correctly con-
nected to the earth (see diagrams in fig. 2 at
the back of the manual).
FOR COOKERS WITH ELECTRIC IGNI-
TION
The correct gaps between the electrode and
the burner are shown in figures 4, 5 and 6.
If no spark is generated, do not keep on try-
ing as this might damage the generator.
Possible causes of malfunctions:
- spark plug damp, dirty or broken;
- electrode-burner gap not correct;
- spark plug wire broken or without sheathing;
- spark discharging to earth (to other parts
of the cooker);
- generator or microswitch damaged;
- air has built up in the pipes (particularly if
the cooker has been out of use for a long
time);
- air-gas mixture incorrect (poor fuel setting).
THE SAFETY DEVICE
The correct gap between the end of the ther-
mocouple sensor and the burner is shown in
figures 4, 5 and 6.
To check that the valve is working properly,
proceed as follows:
- ignite the burner and leave it to work for
about 3 minutes;
- turn off the burner by returning the knob to
off position ( );
- after 90 seconds for hob burners, 60 sec-
onds for oven and grill burners, turn the
knob pointer to the "on" position;
- release the knob in this position and move
a burning match towards the burner; IT
MUST NOT IGNITE.
Time needed to excite the magnet during
ignition: 10 seconds approx.
Automatic tripping time, after flame has been
turned off: not more than 90 seconds for hob
burners; not more than 60 seconds for oven
and grill burners.
IMPORTANT
- Before doing any work inside the cooker,
disconnect the mains plug and shut the gas
tap.
- Never use matches to check the gas cir-
cuit for leaks. If a specific control device is
not available, foam or very soapy water can
be used.
- When re-closing the hob, check that the
electrical wires of the spark plugs (if
present) are not close to the injectors, so
that they cannot run across them.
Installation
GB
335100 ET 50-55 N 28-04-2003, 16:0139
… 39 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Etna 1553wt at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Etna 1553wt in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,33 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info