Manual ESX SXE110.2 (page 10 of 32) (English, German, French, Italian, Spanish)

700200

Zoom out

Zoom in

1/32

INPUT SENSITIVITY

TurnthecontrollerLEVELINPUT(Fig.1,84)oftheampliertotheMINposition.Thenturnthevolumecon-

troller of the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT clockwise until you hear some

distortion. Then turn back the LEVEL INPUT slightly until you hear a cleaner sound.

VARIABLE HIGH PASS FILTER

Iftheamplieristobeusedformid-range/tweeterloudspeakers,settheswitchX-OVER(Fig.1,3)toHP.Then

set the desired cross-over frequency on the HIGH PASS controller (Fig. 1,2). Thus to that only the frequencies

abovethechosencross-overfrequencywillbeamplied.Thiseffectivelyminimizesdistortionsandoverloads

at lower frequencies. A good point to start is at 125 Hz.

If you use big loudspeakers (>20 cm) set X-OVER (Fig. 1,3) to FULL. In this case, the HIGH PASS controller

(Fig. 1,2) is without function.

VARIABLE BASS BOOST

By using the controller BASS BOOST (Fig. 1,7) you are able to increase the bass enhancement from 0 to 12

dB. ATTENTION: Use the BASS BOOST wisely!

HIGH LEVEL INPUTS & AUTO TURN ON

The high level inputs under HI INPUT (Fig. 5) is suitable to connect the device input with speaker wires, if your

headunitisnotequippedwithpre-amplierRCAoutputs.Extendthereforeveryregardingspeakercablefrom

your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the am-

plier.ThenconnecttheeachmatchingloudspeakercablewiththecablesoftheincludedHighLevelInputjack.

CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the

device seriously.

Theamplierdetectsavoltagerise(6Volts)withasocalled”DCOffset”overtheconnectedinputsignalonthe

highlevelinputsunderHIINPUT(Fig.5)whentheheadunitwillbeswitchedon.Hence,theamplierwillalso

beturnedon.Assoonastheheadunitwillbeturnedoff,theamplierturnsalsoautomaticallyoff.Inthiscase

the turn-on connection REM (Fig. 2,2) is not needed.

NOTE: The Auto Turn On function usually works with 90% of all head units, because they are equipped with

”High Power”-outputs. Only with a few older and head units the Auto Turn On function is not working.

PROTECTION CIRCUIT

ThePOWER/PROTECTIONLED(Fig.1,1)lightsupgreen,iftheamplierisinoperation.

ThePOWER/PROTECTIONLED(Fig.1,1)lightsupred,whentheamplierisoverheated,orashortcircuit

occurs respective a too low impedance load is connected to the speaker outputs. If this events, the internal

built-inprotectioncircuitshutsdowntheamplierautomatically.Theampliershouldworkagainproperlyafter

you have solved the problems.

VARIABLE LOW PASS FILTER

Iftheamplierisusedtodriveasubwoofer,settheswitchX-OVER(Fig.1,3)toLP/BP.Setthedesiredcross-

over frequency by using the controller LOW PASS (Fig. 1,4). Thus to that only the frequencies below the cho-

sencross-overfrequencywillbeampliedandthesubwooferplaysmorepreciseandefcient.

In LP/BP mode, the controller HIGH PASS (Fig. 1,2) can also be used to limit the frequency response down-

wards, for example to produce a bandpass/subsonic signal. NOTE: If the controller HIGH PASS (Fig. 1,2) is

set higher than the he controller LOW PASS (Fig. 1,4), no audio signal is heard.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of ESX SXE110.2 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 2,5 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

ESX SXE110.2 Manual

Product: