700198

ESX SXE100.4 Manual

10
Zoom out
Zoom in
Previous page
1/32
Next page
10
INPUT SENSITIVITY CH1/2 & CH3/4
Turn the controller LEVEL INPUT (Fig. 1,4 and g. 1,6) of the amplier to the MIN position. Then turn the vol-
ume controller of the head unit to 80 - 90% of its full setting. Now turn LEVEL INPUT clockwise until you hear
some distortion. Then turn back the LEVEL INPUT slightly until you hear a cleaner sound.
VARIABLE HIGH PASS FILTER CH1/2 & CH3/4
If the amplier is to be used for mid-range/tweeter loudspeakers, set the switches X-OVER (Fig. 1,3 and g.
1,9) to HP. Then set the desired cross-over frequency on the HIGH PASS controller (Fig. 1,2 or g. 1,8). Thus
to that only the frequencies above the chosen cross-over frequency will be amplied. This effectively minimizes
distortions and overloads at lower frequencies. A good point to start is at 125 Hz.
If you use big loudspeakers (>20 cm) set X-OVER (Fig. 1,3 and g. 1,9) to FULL. In this case, the HIGH PASS
controllers (Fig. 1,2 or g. 1,8) are without function.
VARIABLE BASS BOOST CH3/4
By using the controller BASS BOOST (Fig. 1,11) you are able to increase the bass enhancement from 0 to 12
dB. ATTENTION: Use the BASS BOOST wisely!
HIGH LEVEL INPUTS & AUTO TURN ON
The high level inputs under HI INPUT (Fig. 5) is suitable to connect the device input with speaker wires, if your
head unit is not equipped with pre-amplier RCA outputs. Extend therefor every regarding speaker cable from
your head unit with appropriate speaker cables from your car audio retailer to the mounting location of the am-
plier. Then connect the each matching loudspeaker cable with the cables of the included High Level Input jack.
CAUTION: Never use the high level inputs and the RCA inputs at the same time. This may damage the
device seriously.
The amplier detects a voltage rise (6 Volts) with a so called ”DC Offset” over the connected input signal on the
high level inputs under HI INPUT (Fig. 5) when the head unit will be switched on. Hence, the amplier will also
be turned on. As soon as the head unit will be turned off, the amplier turns also automatically off. In this case
the turn-on connection REM (Fig. 2,2) is not needed.
NOTE: The Auto Turn On function usually works with 90% of all head units, because they are equipped with
”High Power”-outputs. Only with a few older and head units the Auto Turn On function is not working.
INPUT MODE
By setting the switch INPUT MODE (Fig. 1,7) to the 2CH position, you switch the inputs to a 2-channel mode,
which allows a four-channel operation with only occupying the inputs CH1/2.
VARIABLE LOW PASS FILTER CH3/4
If the amplier is used to drive a subwoofer on CH3/4, set the switch X-OVER (Fig. 1,9) to LP/BP. Set the
desired cross-over frequency by using the controller LOW PASS (Fig. 1,10). Thus to that only the frequencies
below the chosen cross-over frequency will be amplied and the subwoofer plays more precise and efcient.
In LP/BP mode, the controller HIGH PASS (Fig. 1,8) can also be used to limit the frequency response down-
wards, for example to produce a bandpass/subsonic signal. NOTE: If the controller HIGH PASS (Fig. 1,8) is
set higher than the he controller LOW PASS (Fig. 1,10), no audio signal is heard.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX SXE100.4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX SXE100.4 in the language / languages: English, German as an attachment in your email.

The manual is 2,23 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info