700330
9
Zoom out
Zoom in
Previous page
1/28
Next page
9
POWER SUPPLY AND TURN-ON-CONNECTION
INTERCONNECTION
INSTALLATION
The power wiring which is usually installed in on-board car networks is not sufcient for demands of this de-
vice. Make sure that the power wires to GND and to the +12 V terminal has been sufciently specied. A cable
crosssection of at least 10 mm
2
must be used to connect the battery to the terminals of the device.
First connect the GND terminal (Fig. 1, 13) of the device to an appropriate ground connection at the chassis.
To ensure a good connection, residue dirt and dust from the connection point. A loose connection may cause
malfunctions or interferences noise and distortion.
Then connect the +12 V terminal (Fig. 1, 12) of the device with the battery by using an appropriate cable in-
cluding an in-line fuse (Fig. 1, 14). This fuse should be located very close to the battery (Fig. 1, 15); for safety
reasons not more than 30 cm away. Only insert the fuse when the installation, including the connection of the
loudspeakers, has been accomplished.
Then connect the remote turn-on-wire from the head unit (Fig. 1, 11) with the device‘s REMOTE terminal. A
cable with a cross-section of 0.5 mm
2
is adequate.
1. Mount the device in the car as shown below.
2. Avoid any damage or removing of the components of the vehicle like wires, cables, board computer, seat
belts, gastank or the like.
AUDIO SIGNAL CABLES
When installing the audio cables between the RCA outputs of the head unit and the RCA inputs of the device
(Fig. 1, 8), the audio and power supply cables should, if possible, not be routed along the same side of the
vehicle. We recommend a separated installation, e.g. routing the power cable through the cable channel on the
left side and the audio cables through the cable channel on the right side or vice versa. This prevents interfe-
rences due to crosstalk into the audio signal.
PROTECTION CIRCUIT
If the POWER LED (Fig. 1, 1) lits up blue, the device is in normal operation. If the PROTECT LED (Fig. 1, 1)
lits up red, the device is overheated. If this events, the internal built-in protection circuit shuts down the device
automatically. The device should work again properly after cooling down.
4 x 4 x 4 x
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX Q202A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX Q202A in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 4,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info