700204

ESX HXE110.2 Manual

12
Zoom out
Zoom in
Previous page
1/32
Next page
12
TROUBLESHOOTING
If you are having problems after installation follow the Troubleshooting procedures below.
Procedure 1:
CheckAmplierforproperconnections.
Verify that POWER/PROTECTION LED lits up green. If If this is the case, skip to Step 3, if not continue.
1. Check in-line fuse on battery positive cable. Replace if necessary.
2. Checkfuse(s)onamplier.Replaceifnecessary.
3. Verify that Ground connection is connected to clean metal on the vehicle’s chassis. Repair/replace if necessary.
4. Verify there is 9 to 16 Volts present at the positive battery and remote turn-on cable.Verify quality connections for both cables at
amplier,stereo,andbattery/fuseholder.Repair/replaceifnecessary.
Procedure 2:
POWER/PROTECTION LED lits up red.
1. If the PROTECT lits up red, this is a sign of a possible short in the speaker connections. Check for proper speaker connections
and use an ohm meter to check for possible shorts in the speaker wiring. Too low speaker impedance may also cause PROTECTION
tolight.Thiscanalsobeasignofdrivingtheamplieratveryhighpowerlevelswithoutadequateairowaroundtheamplier.Shut
offthesystemandallowampliertocool.Checkthatthevehiclechargingsystemismaintainingpropervoltage.Ifthepreviousitems
donotsolvetheproblem,afaultmaybeintheamplier.Inthiscaseyoushouldcontactyourdealer.
Procedure 3:
CheckAmplierforaudiooutput.
1. VerifygoodRCAinputconnectionsatstereoandamplier.Checkentirelengthofcablesforkinks,splices,etc.
Test RCA inputs for AC volts with stereo on. Repair/replace if necessary.
Procedure 4:
CheckAmplierforapoppingnoisewhileturningon.
1.Disconnectinputsignaltoamplierandturnamplieronandoff.
2.Ifthenoiseiseliminated,connecttheremoteleadofampliertosourceunitwithadelayturn-onmodule.
Procedure 5:
CheckAmplierifyouexperienceexcessEngineNoise.
1. Route all signal carrying wires (RCA, Speaker cables) away from power and ground wires.
OR
2. Bypassanyandallelectricalcomponentsbetweentheheadunitandtheamplier(s).Connectstereo
directlytoinputofamplier.Ifnoisegoesawaytheunitbeingbypassedisthecauseofthenoise.
OR
3. Remove existing ground wires for all electrical components. Reground wires to different locations.
Verify that grounding location is clean, shiny metal free of paint, rust etc.
OR
4. Add secondary ground cable from negative battery terminal to the chassis metal or engine block of vehicle.
OR
5. Have alternator and battery load tested by your mechanic.Verify good working order of vehicle electrical system including distributor,
spark plugs, spark plug wires, voltage regulator etc.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX HXE110.2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX HXE110.2 in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 3,52 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info