700319
5
Zoom out
Zoom in
Previous page
1/8
Next page
5
ENGLISH
IMPORTANT NOTES
Choose a suitable location for your soundsystem, that neither the drivers eld of vision nor the
security of the inmates will be affected. This stands also for airbag-zones and safety belts. The per-
manent temperature of the location should not be lower than 5°C and not higher than 50°C. Protect
the device from moisture and humidity.
Ensure that your subwoofer enclosure will not get loose during the drive and hurt someone in the
passenger cabin. It is recommended, that you mount the subwoofer enclosure with suitable belts or
any other mounting solutions in the trunk area.
Please observe not to damage any serial components of your vehicle (airbags, wires, gastank etc.)
during the installation of your soundsystem by drilling or any other operations.
Never screw or mount any other devices (amps, caps etc.) onto the subwoofer enclosure, this may
cause damage to the electricity.
For your personal concerns you should choose a appropriate sound level for the subwoofer enclo-
sure, that neither the roadworthy of the driver nor his concentration will be disturbed, that he is able
to notice possible trafc noises and acoustical warning signals.
Modern car audio soundsystems provide very high acoustic pressure beyond the 100 dB mark.
Please observe in this case, that permanent use of high sound levels may cause damage to your
ability of hearing.
Please ensure by any means the correct polarity of all connections. Faulty installed and connected
devices may get damage the vehicle and the device permanently.
Please check in any case the operation guide or wiring manual of your amplier which you’d like to
use for the soundsystem.
Never connect the speaker terminals with the 12 Volt power supply, otherwise the speakers may
get damaged.
POWER RATING
ESX subwoofer enclosures are designed for high bass levels. Anyhow it is possible, that unsatisfy-
ing sound characteristics could be caused by too low or too high amplier power. In certain circum-
stances this even can cause a damage to the loudspeakers.
It is recommended to choose rather a more powerful amplier (ca. 15-20% more Watts RMS than
the max. RMS power rating of the woofer) and to use the amplier not at the maximum output level
(low distortion factor, good sound characteristics). A weaker amplier at the maximum level causes
worse sound characteristics due to the higher distortion factor.
Never crank up the output volume of your amplier to the maximum level or run the amplier into
the clipping range. If the sound is distorted and not clean, turn back the level until the distortions
disappear.
ESX subwoofer enclosures have no integrated limiter or clipper, which is limiting the level upwards.
Overamplied bass peaks leads inevitably to a burn out of the voice coil of the woofer. A burn out of
the voice coil, caused by clipping/overamping is not covered by the usual warranty.
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for ESX DBX200Q at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of ESX DBX200Q in the language / languages: English, German as an attachment in your email.

The manual is 0,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info