617671

Epson SureColor SC-F2000 Manual

84
Zoom out
Zoom in
Previous page
1/104
Next page
o
Is there any lint or standing fibers on the print
surface?
Lint or standing fibers on the print surface may stick to
the print head and stain other areas of the T-shirt.
R em ov e a ny li nt wi th th e s ti ck y t ap e o r r ol le r a nd pr es s
the fibers flat with a hard roller when you load a T-shirt
on the platen.
U “Loading on the Platen” on page 33
o
Clean around the print head.
If the printing surface and so on is dirty even after
performing cap cleaning, fibers, such as lint, may have
accumulated around the print head nozzles. Clean
around the print head.
U “Cleaning around the print head” on page 63
Not enough or uneven whiteness
o
Are the print head nozzles clogged?
If the nozzles are clogged, nozzles do not fire ink and
the print quality declines. Print a nozzle check pattern.
U “Checking for clogged nozzles” on page 44
o
Have you shaken White ink cartridges?
Because the ink particles in White ink can sediment
easily, it needs to be shaken at the start of every
working day or every 20 hours (when a message is
displayed). Remove the cartridge and shake it.
U “Replacing and Shaking Cartridges” on page 58
o
Have you applied the pre-treatment liquid
evenly?
If the pre-treatment liquid is not applied evenly, the
printed result will be uneven. Refer to the instructions
and apply the pre-treatment liquid evenly.
U “Using Pre-treatment Liquid” on page 26
o
Have you dried the T-shirt completely after
pre-treatment?
If the T-shirt is in the following condition, whiteness
may decline.
❏ Insufficient heat press process
❏ Moisture has accumulated because the T-shirt
was left for an extended period of time
Dry the T-shirt completely after the pre-treatment
referring to the fixation conditions. If the T-shirt is left
for an extended period, dry it for several seconds in
the heat press before printing.
U “Fixating the Pre-treatment Liquid (Heat Press)”
on page 29
o
Have you optimized the temperature and
pressure of the heat press?
The temperature of the heat press decreases when
you press a T-shirt that has had pre-treatment liquid
applied. When pressing several T-shirts one after
another, check that the temperature of the heat press
is not lower than required. Also, the whiteness
becomes uneven if the pressure is insufficient since
the T-shirt does not dry completely and the fibers are
not pressed flat. Make sure you optimize the pressure
of the heat press.
U “Fixating the Pre-treatment Liquid (Heat Press)”
on page 29
o
Have you washed the ink tubes?
Because the ink particles in White ink can sediment
easily, you need to wash the tubes when a message is
displayed. Prepare the following consumables when
washing the tubes.
❏ White ink cartridges x2
❏ Cleaning cartridges x2
❏ Waste ink bottle
U “Options and Consumable Products” on
page 87
U “Tube Washing” on page 56
The under-base white is showing
outside the image
o
Adjust the print area of the under-base white
in the software.
The printed under-base white may show outside the
image depending on the material of the T-shirt and
the amount of ink fired. If this occurs, adjust the print
area of the under-base white from the printer's
Garment Creator software or the RIP software.
Others
The control panel display keeps
turning off.
o
Is the printer in sleep mode?
Normal operation can be restored by pressing any of
the buttons in the control panel to reactivate the
display and then performing a hardware operation
such as opening the printer cover or sending a job to
the printer. The delay before the printer enters sleep
mode can be selected in Maintenance Mode.
U “Maintenance Mode” on page 77
SC-F2000 Series User’s Guide
Problem Solver
84
… 84 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson SureColor SC-F2000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson SureColor SC-F2000 in the language / languages: English as an attachment in your email.

The manual is 4,43 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson SureColor SC-F2000

Epson SureColor SC-F2000 Quick start guide - English, German - 33 pages

Epson SureColor SC-F2000 User Manual - German - 121 pages

Epson SureColor SC-F2000 User Manual - Dutch - 112 pages

Epson SureColor SC-F2000 Quick start guide - Dutch, French, Italian, Portuguese, Spanish - 33 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info