37861
24
Zoom out
Zoom in
Previous page
1/27
Next page
24 Solving Problems
Problems and Solutions
Check the solutions below if you are having
problems using the product.
Setup problems
The product makes noise after you turn it on.
Make sure the protective tape is not blocking the
print head. After releasing the print head, turn
off the power, wait a moment, then turn it back
on.
The product makes noise after ink cartridge
installation.
When you install ink cartridges, the ink delivery
system must be charged. Wait until charging is
finished, then turn off the product. If you turn it
off too soon, it may use extra ink the next time
you turn it on.
Make sure the ink cartridges are seated securely
and no protective material remains in the
product. Open the cartridge cover and push the
cartridges down until they click into place. Turn
off the power, wait a moment, then turn it back
on.
A screen that prompts you to restart the computer
did not appear after finishing the software
installation.
The software has not been installed correctly.
Eject and insert the CD-ROM, and then install
the software again.
Printing and copying problems
The product is on, but nothing prints.
Run a nozzle check (& “Checking the print
head” on page 20). If nothing prints, you may
need to clean the print head.
The product makes printing sounds, but nothing
prints.
The print head nozzles may need cleaning
(& “Checking the print head” on page 20).
Make sure the product is on a flat, stable surface.
The margins are incorrect.
Make sure your original is positioned in the top
left corner of the document table.
If the edges of the copy are cropped off, move the
original away from the corner slightly.
Make sure the paper size settings are correct for
the paper you have loaded.
Make sure your paper is loaded short edge first,
all the way to the right, with the left edge guide
lightly against the paper (& “Loading Paper” on
page 8).
Do not load paper above the c arrow mark
inside the left edge guide (& “Loading Paper” on
page 8).
Blank pages are printed.
Make sure the paper size settings are correct for
the paper you have loaded.
The print head nozzles may need cleaning
(& “Cleaning the print head” on page 20).
Paper feed problems
Paper does not feed correctly or is jammed.
If paper does not feed, remove it from the sheet
feeder. Fan the paper, load it against the right
side, and slide the left edge guide against the
paper (but not too tightly). Make sure the paper
is not in front of the feeder guard.
Do not load paper above the c arrow mark
inside the left edge guide (& “Loading Paper” on
page 8).
If paper is jammed, the b Error light flashes.
Follow these steps to clear the jam:
1. Press the x Start E [Color] button to eject the
jammed paper. If the jammed paper is not
ejected, go on to the next step.
2. If the paper is stuck near the sheet feeder or
output tray, gently pull it out then press the
x Start E [Color] button.
If the paper is stuck inside the product, press the
P On button to turn it off. Open the scanner unit
and remove any paper inside, including any torn
pieces. Do not pull it backward; this can damage
the sheet feeder. Close the scanner unit, then
turn the product back on.
If paper jams frequently, make sure the left edge
guide is not pushed too tightly against the paper.
Try loading fewer sheets of paper.
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson Stylus DX5000 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson Stylus DX5000 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,65 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson Stylus DX5000

Epson Stylus DX5000 User Manual - Dutch - 28 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info