589524

Epson Runsense SF510 Manual

2
Zoom out
Zoom in
Previous page
1/2
Next page
Use low pressure water
to wash the device.
Contact points
Contact marks
12. Service and Repair
Go to
www.epson.eu/runsense
for service contact details.
Looking after your Device
To clean the device, wash the contact points lightly with tap water, wipe away most of the water
with a towel, and then let it dry naturally.
If charging or communicating becomes unstable, clean the contact points on the device and the
cradle with a damp cotton swab.
Do not use any cleaning products on this device.
Option
You can purchase the following optional extras. Contact your local dealer for more information.
• AC adapter Model No. : SFAC02(Conti) / SFAC03(UK)
• Heart Rate Monitor Strap Model No. : SFHRM01
Resetting the System
You can reset the system by following the below steps.
Hold down all of the buttons ( / / / ).
The screen is reset and the device restarts.
Initialise the device after restarting.
“2. Charging and Initial Settings”
Setting data and measurement data remain as they were before the reset was performed.
The time screen will automatically be updated the next time a GPS signal has been
received.
Goal function
This function allows you to measure until the time or distance set in advance is reached.
Time race
Allows you to set a time as your goal and measure the time taken until that goal is reached. You can
exercise while checking the elapsed time. You can also calculate the estimated distance until the goal is
reached.
Distance race
Allows you to set a distance as your goal and measure the time taken until that goal is reached. You can
exercise while checking the distance. You can also calculate the estimated time.
1. Display the measurement screen.
Press on the time screen. GPS positioning starts, and the measurement screen is displayed
once positioning is complete.
2. Displays the Measure set. menu.
Hold down on the measurement screen.
3. Select Mode.
4. Select Goal.
5. Select whether to set Time or Distance.
6. Set the Time or Distance.
7. Select OK.
8. Press to start measuring.
When the set time or distance is reached, the “Finish” screen is displayed.
An alarm noties you when you reach 50% and 90% of the set time or distance.
Set the “Estimated Time” or “Estimated Distance” in your screen settings to view and keep track of your
progress. For more details, see the User Manual.
Measure set.
You can set the following measurement related functions from the Measure set. menu.
To open the Measure set. menu, hold down
on the measurement screen before you start recording.
Setting items Value Explanation (The initial settings are underlined)
Activity Type
Run, Walk, Bike Select the Activity Type you want to measure.
Mode Set the Mode to suit the measurements you want to make.
Chronograph Chronograph mode allows you to measure split times and
lap times (section measurement) simultaneously.
Interval Interval mode allows you to switch between hard (sprint)
or light (recovery) exercises, and repeat using the specic
distance or time set in advance.
Goal Goal mode measures until the time or distance set in
advance is reached.
GPS - Displays the number of GPS satellites being accessed.
AT Lap
SETTING 01-05
OFF
This function records laps automatically, when a time or
distance set in advance is reached. You can set ve times or
distances.
AT Pause
ON
OFF
This function automatically stops measuring when you stop
running, and resumes when you continue running.
Target Pace
SETTING 01-03
OFF
Set the target time and pace range for the distance. An alarm
sounds if you are outside the set pace range. You can set three
target paces.
Waypoint ON
OFF
Store the waypoint that you want to reach from the current
position. An alarm sounds if you reached the waypoint..
HR*
1
Zone 1-5
OFF
You can measure your heart rate by wearing the Heart Rate
Monitor Strap (optional). We recommend using the optional
Heart Rate Monitor Strap (Model No.: SFHRM01)
Tap*
2
(Only for the
measurement screen)
Lap, Light, Screen
Chg., OFF
You can perform one of the operations set here by tapping
the screen while measuring.
Screen Screen 1-4
Display Lap Screen
You can display up to four measurement screens. You can
change the screen pattern and the measurement items
displayed for each screen.
You can also change the Lap Screen, but this is not displayed
for the interval function.
*1 Displayed after registering the Heart Rate Monitor.
*2 Only displayed for the SF-710/SF-510.
Settings
You can set the following device related functions from the Settings menu.
To open the Settings menu, hold down
on the time screen.
Setting items Value Explanation
Comm. Settings HR Monitor
Smart Phone
Register the Heart Rate Monitor and the
smartphone to this device.*
1
User Settings Height, Weight, DOB, Gender, HR
Zone*
1
Set the user information.
Sys. Settings Language, Units, Clock, DST, Time
Adjust, Time Zone, Date Format,
Invert Disp., Contrast, Auto Sleep,
AT Light, Alarm, Key Tones, Initialize,
Software Version
Make settings for the device's system.
*1 For more information on the Heart Rate Monitor and smartphones, download the User Manual from
the following Epson website. www.epson.eu/runsense
8. Settings Table
9. Introduction of the main function
11. Other Features described in the User Manual
10. Maintenance
• How to set a time and distance for hard and light workouts (Interval Function)
• How to set and measure the target time for one kilometer (Target Pace function)
• How to monitor your heart rate with the Heart Rate Monitor (Heart rate function)
• How to communicate with external devices (Communication function)
• How to set the Tap Function to display a set function (Tap function: SF-710/SF-510 only)
• How to set the device to turn on the light automatically when the screen changes (AT Light function)
For more information on each of the functions mentioned above, download the User Manual from
the following Epson website.
www.epson.eu/runsense
Installing the Run Connect
This device allows you to manage measured data using a dedicated Web application (RUNSENSE
View). To upload measurement data, you need to install Run Connect on your computer and connect
to the Internet.
Install Run Connect before connecting the device to your computer.
1. Access the following website and download Run Connect.
URL https://go-wellness2.epson.com/portal/
2. Run the downloaded le and follow the instructions displayed on the setup
screen.
Creating an Account (When Using RUNSENSE View for the First Time)
1. Connect the cradle with a USB cable to the PC on which Run Connect is
installed.
2. Place the device into the cradle.
Check that the contact points on the device are pointing up and match the contact marks
on the cradle.
Run Connect starts.
3. Click Create Account and enter your details.
Uploading your recorded Data
Connect your RUNSENSE device to the computer. The following box will
automatically appear. Enter your Login ID and Password and click Upload.
View your recorded Data
1. Click Start RUNSENSE View on the Run Connect screen.
Or access the following Web site.
URL https://go-wellness.epson.com/runsense-view/
2. Click the data you want to check from the list.
• For information on using the Web application (RUNSENSE View), see the RUNSENSE View Help.
• For information on linking to other devices, see the User Manual.
AT Lap
When a time or distance set in advance is reached, laps are recorded automatically. Set the lap time or
distance. You can set ve times or distances. However, only one setting can be used while measuring.
1. Display the measurement screen.
Press on the time screen. GPS positioning starts, and the measurement screen is displayed
once positioning is complete.
2. Displays the Measure set. menu.
Hold down on the measurement screen.
3. Select AT Lap.
4. Select one of the No Data from 1 to 5.
5. Select whether to set Time or Distance as the length of the lap.
6. Set the Time or Distance.
7. Press to complete the settings.
8. Hold down again to return to the measurement screen.
9. Press to start measuring.
AT Pause
Measuring stops automatically when you stop running, and resumes when you continue running.
1. Display the measurement screen.
Press on the time screen. GPS positioning starts, and the measurement screen is displayed
once positioning is complete.
2. Displays the Measure set. menu.
Hold down on the measurement screen.
3. Select AT Pause.
4. Select ON.
5. Press to complete the settings.
6. Hold down again to return to the measurement screen.
7. Press to start measuring.
7.
Data Management Using the Web Application (RUNSENSE View)
MEMO
MEMO
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson Runsense SF510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson Runsense SF510 in the language / languages: English as an attachment in your email.

The manual is 0,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson Runsense SF510

Epson Runsense SF510 User Manual - English - 149 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info