675425
8
Zoom out
Zoom in
Previous page
1/9
Next page
8
LW-K400 User’s Guide
Troubleshooting
J Messages
Insert Tape No tape cartridge is installed. Turn the power o and install a
tape cartridge correctly.
Check tape! A tape cartridge which cannot be used in this product has
been set. Check the tape cartridge.
Check tape
cartridge
A tape cartridge which cannot be used in this product has
been set. Check the tape cartridge.
Check battery Possible causes for this message are:
No power remaining or inserted in the wrong way
Mixed with other types or old ones
If so, set the batteries correctly or replace them with new
ones.
Too many lines Text entered is too long.
Press
to delete the lines indicated by the cursor.
Text too long Entered text is too long for the specied tape length. Press
and adjust the tape length or make text shorter.
Seq. num. only 1
Sequence numbers have already been set. Sequence numbers can
be used for one part only.
Text will be
deleted. OK?
When creating a label with a special form,
current text will be deleted. Press to delete the text and
show the special form.
Fill every digit Entered values for barcodes are wrong. Check the entries
about values, digits, etc.
Load wider tape Unable to print on the current tape. Use a wider tape.
Txt is too long
Continue?
Entered text is too long for the specied tape length. Press
to print in the correct length.
Overheated! The printhead is too hot. Turn the power o and take out the
tape cartridge. Wait for a while before start printing again.
Cover open!
Powering o.
If you open the cover on the rear without turning the power
o, a message is displayed and then the power is turned o
automatically.
Motor error! An error occurred in the motor operation. Turn the power
o once, then turn it back on. If the same message appears,
turn the power o and contact the EPSON customer support
centre.
J
Problems
Does not operate normally.
Initialise this product if it does not operate normally such as the power cannot
be turned on or o, or the display is interrupted.
No image comes out even though has been pressed.
Are the batteries correctly set?
Check if all the batteries are correctly set.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter
(APT0615Z).
Is the AC adapter securely connected?
Connect the AC adapter and the power cable rmly to the power socket of the
product, the AC adapter connector and the outlet.
Are you using an AC adapter other than the dedicated one?
Using an AC adapter other than the dedicated one (APT0615Z) is very
dangerous, and may cause overheating or damage to the electric circuits.
Is the display level appropriate?
Adjust the display level.
Display has turned o.
Did you enable the auto power-o function?
The power turns o automatically if no operation is made for more than
5minutes.
Did you try to carry out a function incorrectly?
If buttons are operated incorrectly, the display turns o for a moment.
Nothing is printed even though has been pressed.
Is text entered?
Nothing is printed if no text is entered.
Any message on the display?
Read the message and take the appropriate action.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace the batteries with new ones, or use the dedicated AC adapter
(APT0615Z).
Is the cover on the rear open?
Set the tape cartridge correctly and close the cover completely.
Characters are not printed properly.
Is the tape cartridge correctly set?
Set the tape cartridge correctly.
Is the printhead dirty?
Clean the printhead.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z).
Printing ends in the middle of text.
Did the tape run out?
Install a new tape cartridge.
Did the batteries run out?
Replace them with new ones, or use the dedicated AC adapter (APT0615Z).
Created text has gone.
Did you delete the text?
If + are pressed, the text on the display will be deleted.
Did you initialise the product?
If the product is initialised, all the created text will be deleted.
Did you remove the batteries or the AC adapter when the product was in
operation?
If the AC adapter or the batteries are removed during operation, the text may
be deleted.
Cannot attach the label.
Did you peel the backing paper?
Attach the label after peeling the backing paper.
Are you attaching it on a dirty place or on a place with a rough surface?
The label may not adhere due to the material of the attachment location or the
environmental conditions.
MEMO
If none of the above has solved the problem or the symptom is other
than the above, contact the EPSON customer support centre.
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson LW-K400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson LW-K400 in the language / languages: English as an attachment in your email.

The manual is 0,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson LW-K400

Epson LW-K400 User Manual - German - 9 pages

Epson LW-K400 User Manual - Dutch - 9 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info