655245
27
Zoom out
Zoom in
Previous page
1/146
Next page
Code Solution
E-2
E-3
E-7
Make sure that the access point is turned on.
Check that the computer or other devices are connected correctly to the access point.
Place the printer close to the access point. Remove any obstacles between them.
If you have entered the SSID manually, check if it is correct. Check the SSID from the Network Status part on
the network connection report.
To establish a network using push button setup, check that the access point supports WPS. If it does not
support WPS, you cannot establish a network using push button setup.
Check that only ASCII characters (alphanumeric characters and symbols) are used for the SSID. The printer
cannot display an SSID which contains any characters other than ASCII characters.
Check the SSID and password before connecting to the access point. If you are using an access point with its
default settings, the SSID and password are on the label. If you do not know the SSID and password, contact
the person who set up the access point, or see the documentation provided with the access point.
When you want to connect to an SSID generated using the tethering function on a smart device, check the
SSID and password in the documentation provided with the smart device.
If the Wi-Fi connection is suddenly disconnected, check the following. If any of these are applicable, reset the
network settings using the installer. You can run it from the following website.
http://epson.sn > Setup
Another smart device was added to the network using push button setup.
The Wi-Fi network was set up using any method other than push button setup.
E-5 Make sure the access point's security type is set to one of the following. If it is not, change the security type on
the access point, and then reset the printer's network settings.
WEP-64 bit (40 bit)
WEP-128 bit (104 bit)
WPA PSK (TKIP/AES)
*
WPA2 PSK (TKIP/AES)
*
WPA (TKIP/AES)
WPA2 (TKIP/AES)
* : WPA PSK is also known as WPA Personal. WPA2 PSK is also known as WPA2 Personal.
E-6 Check if the MAC address ltering is disabled. If it is enabled, register the printer's MAC address so that it is
not ltered. See the documentation provided with the access point for details. You can check the printer's
MAC address from the Network Status part on the network connection report.
If the access point's shared authentication is enabled on the WEP security method, make sure the
authentication key and index are correct.
E-8 Enable DHCP on the access point when the printer's Obtain IP Address is set to Auto.
If the printer's Obtain IP Address is set to Manual, the IP address you manually set is out of range (for
example: 0.0.0.0) and it is disabled. Set a valid IP address from printer's control panel or Web Cong.
E-9 Check the following.
Devices are turned on.
You can access the Internet and other computers or network devices on the same network from the devices
you want to connect to the printer.
If it still does not work after checking the above, reset the network settings using the installer. You can run it
from the following website.
http://epson.sn > Setup
User's Guide
Network Settings
27
27


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson L605 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson L605 in the language / languages: English as an attachment in your email.

The manual is 3,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson L605

Epson L605 Quick start guide - English - 4 pages

Epson L605 User Manual - German - 149 pages

Epson L605 Quick start guide - German - 4 pages

Epson L605 User Manual - Dutch - 147 pages

Epson L605 Quick start guide - Dutch, Danish - 4 pages

Epson L605 User Manual - French - 149 pages

Epson L605 Quick start guide - French - 4 pages

Epson L605 Quick start guide - Italian - 4 pages

Epson L605 Quick start guide - Spanish, Spanish - 4 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info