537685
152
Zoom out
Zoom in
Previous page
1/156
Next page
User's Guide
Notations Used in This Guide
Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
Please understand and respect these caution symbols in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
General information indications
Attention
Indicates procedures which may result in damage or injury if sufficient care is not taken.
a
Indicates additional information and points which may be useful to know regarding a topic.
s Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendix".
s "Glossary" p.151
[Name] Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Menu Name Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Notations Used in This Guide ........................ 2
Introduction
Part Names and Functions ................................... 8
Front/Top...................................................8
Rear....................................................... 9
Interface.................................................... 9
Base......................................................10
Control Panel................................................11
Remote Control ...............................................12
Replacing the remote control batteries.............................14
Remote control operating range.................................15
Preparing the Projector
Installing the Projector ..................................... 18
Installation Requirements........................................18
Screen Settings ............................................... 19
Adjusting the position of the image on the projected screen..............20
Displaying a Test Pattern........................................21
Adjusting the Position of the Projected Image (Lens Shift)..................22
Adjusting the Image Size ........................................24
Correcting the Focus...........................................24
Adjusting the Image Position.....................................24
Adjusting the Horizontal Tilt ......................................24
ID Settings..................................................25
Set the projector ID..........................................25
Checking the Projector ID ......................................25
Setting the remote control ID................................... 25
Setting the Time ..............................................26
Connecting Equipment ..................................... 28
Connecting a Computer......................................... 28
Connecting Image Sources .......................................30
Connecting External Equipment...................................32
Connecting a LAN Cable .........................................33
Installing the Wireless LAN Unit ....................................34
Attaching the Cable Cover .......................................35
Attaching .................................................35
Basic Usage
Projecting Images ......................................... 38
Automatically Detect Input Signals and Change the Projected Image (Source Search)
..........................................................38
Switching to the Target Image by Remote Control.......................39
Adjusting the Volume..........................................39
Adjusting Projected Images ................................ 40
Correcting Distortion in the Projected Image...........................40
H/V-Keystone..............................................40
Quick Corner...............................................41
Arc Correction ..............................................42
Point Correction............................................43
Selecting the Projection Quality (Selecting Color Mode)...................44
Projecting 3D images(EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only)
........................................................ 45
Changing the Aspect Ratio of the Projected Image ......................45
Changing methods..........................................46
Adjusting the Image...........................................48
Hue, Saturation, and Brightness Adjustment.........................48
Gamma Adjustment..........................................49
Correcting the Color Difference when Projecting from Multiple Projectors.......50
Summary of correction procedure................................50
Correcting................................................50
Useful Functions
Projection Functions ....................................... 53
Projecting Two Images Simultaneously (Split Screen) .....................53
Contents
3
Operating procedures........................................53
Restrictions during split screen projection...........................55
Hiding the Image and Sound Temporarily (A/V Mute).....................56
Freezing the Image (Freeze)......................................57
Enlarging Part of the Image (E-Zoom)................................57
Saving a User's Logo...........................................58
Memory Function .......................................... 60
Saving/Loading/Erasing the Memory................................60
Scheduling Function ....................................... 62
Saving a Schedule .............................................62
Setting Methods............................................62
Editing a schedule...........................................63
Security Functions ......................................... 65
Managing Users (Password Protection) ............................... 65
Kinds of Password Protection...................................65
Setting Password Protection ....................................65
Entering the Password ........................................66
Restricting Operation........................................... 67
Control Panel Lock...........................................67
Remote control button lock ....................................68
Anti-Theft Lock...............................................68
Installing the wire lock........................................69
Configuration Menu
Using the Configuration Menu .............................. 71
List of Functions ........................................... 72
Configuration Menu Table.......................................72
Network menu.............................................73
Image Menu.................................................74
Signal Menu.................................................75
Settings Menu ................................................ 77
Extended Menu ...............................................78
Network Menu............................................... 81
Notes on operating the Network menu............................. 82
Soft keyboard operations......................................83
Basic menu ................................................ 83
Wireless LAN menu..........................................84
Security menu .............................................85
Wired LAN menu............................................87
Mail menu................................................88
Others menu..............................................89
Reset menu............................................... 90
Info Menu (Display Only)........................................91
Reset Menu.................................................92
Troubleshooting
Using the Help ............................................. 94
Problem Solving ........................................... 95
Reading the Indicators.......................................... 95
When the Indicators Provide No Help................................99
Problems Relating to Images .....................................100
No images appear.......................................... 100
Moving images are not displayed ................................100
Projection stops automatically.................................. 101
The message Not supported is displayed ...........................101
The message No Signal is displayed.............................. 101
Images are fuzzy, out of focus, or distorted......................... 102
Interference or distortion appear in images ......................... 102
The image is truncated (large) or small, the aspect is not suitable, or the image has
been reversed .............................................103
Image colors are not right.....................................104
Images appear dark......................................... 105
Problems when Projection Starts .................................. 105
The projector does not turn on................................. 105
Other Problems ..............................................106
No sound can be heard or the sound is faint........................ 106
The remote control does not work ............................... 107
Nothing appears on the external monitor.......................... 108
Contents
4
I want to change the language for messages and menus ................ 108
Email is not received even if a problem occurs in the projector ............ 108
The battery that saves your clock settings is running low. is displayed ....... 109
Cannot change settings using a Web browser....................... 109
About Event ID ........................................... 110
Maintenance
Cleaning ................................................. 112
Cleaning the Projector's Surface...................................112
Cleaning the Lens............................................ 112
Cleaning the Air Filter ..........................................112
Cleaning the air filter ........................................ 112
Replacing Consumables ................................... 115
Replacing the Lamp........................................... 115
Lamp replacement period.....................................115
How to replace the lamp ...................................... 115
Resetting the lamp hours..................................... 118
Replacing the Air Filter......................................... 118
Air filter replacement period................................... 118
How to replace the air filter .................................... 118
Notes on Transportation .................................. 120
Moving Nearby .............................................. 120
When Transporting ........................................... 120
Preparing packaging........................................ 120
Notes when packing and transporting............................ 120
Image Maintenance ....................................... 121
Panel Alignment ............................................. 121
Color Uniformity............................................. 122
Appendix
Network Functions ....................................... 126
Using the Quick Wireless Connection USB Key ......................... 126
Monitoring and Controlling ............................... 127
About EasyMP Monitor .........................................127
About Message Broadcasting.................................. 127
Changing Settings Using a Web Browser (Web Control) ................... 127
Projector setup ............................................ 127
Displaying the Web Control screen ...............................127
Using the Mail Notification Function to Report Problems..................128
Reading Error Notification Mail................................. 128
Management Using SNMP ...................................... 129
Displaying the Web Remote Screen................................ 129
ESC/VP21 Commands..........................................130
Command list............................................. 130
Cable layouts............................................. 131
About PJLink................................................132
About Crestron RoomView
®
..................................... 132
Operating a projector from your computer......................... 133
Optional Accessories and Consumables .................... 137
Optional Accessories.......................................... 137
Consumables............................................... 137
Screen Size and Projection Distance ........................ 138
Projection Distance (For EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU) .....138
Projection Distance (For EB-4750W)................................ 140
Projection Distance (For EB-4650/EB-4550)........................... 142
Supported Monitor Displays ............................... 144
Supported Resolutions......................................... 144
Computer signals (analog RGB)................................. 144
Component Video .......................................... 144
Composite video........................................... 144
Input signal from the HDMI port and DisplayPort (EB-4955WU/EB-4950WU/
EB-4855WU/EB-4850WU/EB-4750W) .............................. 145
Contents
5
Input signal from the HDMI port and DisplayPort (EB-4650/EB-4550) . .......145
Specifications ............................................ 146
Projector General Specifications ...................................146
Appearance .............................................. 150
Glossary ................................................. 151
General Notes ............................................ 153
Trademarks and Copyrights ......................................153
Index .................................................... 154
Contents
6
Introduction
This chapter explains the names for each part.
Unless otherwise specified, the illustrations used in this guide are for
EB-4950WU.
Front/Top
Name Function
A
Air exhaust vent
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent. Hot air from the air exhaust vent could
cause burns, warping, or accidents to occur.
Name Function
B
Focus ring
Adjusts the image focus.
s "Correcting the Focus" p.24
C
Zoom ring
Adjusts the image size.
s "Adjusting the Image Size" p.24
D
Remote receiver
Receives signals from the remote control.
E
Status indicators
The color of the indicators and whether they are flashing
or lit indicate the status of the projector.
s "Reading the Indicators" p.95
F
Air intake vent
(air filter)
Takes in air to cool the projector internally.
s "Cleaning the Air Filter" p.112
G
Air filter cover
operation knob
Use this knob to open the air filter cover.
s "Replacing the Air Filter" p.118
H
Wireless LAN unit
cover
When wirelessly connecting the projector to a computer,
remove this cover and install the optional wireless LAN
unit.
s "Installing the Wireless LAN Unit" p.34
I
Wireless LAN indicator
Indicates the access status of the optional wireless LAN
unit.
s "Optional Accessories" p.137
J
Cable cover
Cover for the rear interface cable connection section.
s "Attaching the Cable Cover" p.35
K
Vertical lens shift dial
Turn the dial to move the position of the projected image
up or down.
s "Adjusting the Position of the Projected Image (Lens
Shift)" p.22
L
Lens shift dial lock
Locks or releases the lens shift dials.
M
Horizontal lens shift
dial
Turn the dial to move the position of the projected image
left or right.
s "Adjusting the Position of the Projected Image (Lens
Shift)" p.22
Part Names and Functions
8
Name Function
N
Lamp cover
Open when replacing the projector's lamp.
s "Replacing the Lamp" p.115
O
Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s "Anti-Theft Lock" p.68
Rear
Name Function
A
Power inlet
Connects to the power cable.
B
Interface
s "Interface" p.9
C
Control panel
s "Control Panel" p.11
D
Speaker
Outputs audio.
E
Cable holder
Insert the supplied cable clamp here to prevent the HDMI
cable from falling out.
s Quick Reference
Interface
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
EB-4750W/EB-4650/EB-4550
Name Function
A
Audio1 port
Inputs audio from equipment connected to the Computer
port.
Part Names and Functions
9
Name Function
B
Computer port
For analog RGB signals from a computer and component
video signals from other video sources.
C
BNC port
For analog RGB signals from a computer and component
video signals from other video sources.
D
Monitor Out port
Outputs to an external monitor the analog signal from the
computer connected to the Computer port or the BNC
port. You cannot output signals input from other ports or
component video signals.
E
Audio Out port
Outputs audio from the currently projected image to an
external speaker.
F
RS-232C port
When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s "ESC/VP21 Commands" p.130
G
Remote port
Connects the optional remote control cable set and inputs
signals from the remote control. When the remote control
cable is plugged into the Remote port, the remote receiver
on the projector is disabled.
s "Optional Accessories" p.137
H
Audio2 port
Inputs audio from equipment connected to the BNC port.
I
Audio-L/R port
Inputs audio from equipment connected to the Video port
or the S-Video port.
J
S-Video port
For S-video signals from video sources.
K
Video port
Inputs composite video signals from video sources.
L
HDMI port
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with
HDCP
g
.
M
Audio3 port
Inputs audio from equipment connected to the
DisplayPort or the HDMI port.
N
DisplayPort
Inputs video signals from DisplayPort compatible
computers. This projector is compatible with
HDCP
g
.
O
LAN port
Connects a LAN cable to connect to a network.
Name Function
P
Service port
This port is used by maintenance personnel to control the
projector. This should not normally be used.
Base
Name Function
A
Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.69
Part Names and Functions
10
Name Function
B
Rear feet
When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt.
s "Adjusting the Horizontal Tilt" p.24
C
Screw hole to fix the
cable cover
Screw hole to fix the cable cover in place.
s "Attaching the Cable Cover" p.35
D
Ceiling mount fixing
points (four points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s "Installing the Projector" p.18
s "Optional Accessories" p.137
E
Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.24
Control Panel
Name Function
A
[t] button
Turns the projector power on or off.
B
[Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
Name Function
C
[ ]/[ ] buttons
Displays the Control Panel Lock screen allowing you to
make settings to lock the control panel buttons.
s
"Restricting Operation" p.67
If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s "Using the Configuration Menu" p.71
s "Using the Help" p.94
D
[ ] button
When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
If pressed while projecting analog RGB signals from the
Computer port or the BNC port, you can automatically
optimize Tracking, Sync., and Position.
E
[ ]/[ ] buttons
Displays a test pattern.
s "Displaying a Test Pattern" p.21
If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s "Using the Configuration Menu" p.71
s "Using the Help" p.94
F
[ ] /[ ] buttons
Displays the Info menu from the Configuration menu.
s "Info Menu (Display Only)" p.91
If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s "Using the Configuration Menu" p.71
s "Using the Help" p.94
G
[A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.56
Part Names and Functions
11
Name Function
H
[Esc] button
Stops the current function.
If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s "Using the Configuration Menu" p.71
I
[ ]/[ ] buttons
Performs screen adjustments using the settings in
Geometric Correction from the Configuration menu.
s Settings - Geometric Correctionp.77
If pressed when the Configuration menu or the Help
screen is displayed, this button selects menu items and
setting values.
s "Using the Configuration Menu" p.71
s "Using the Help" p.94
J
[Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.71
Remote Control
Part Names and Functions
12
Name Function
A
[ ] button
Turns the projector on.
B
[t] button
Turns the projector off.
C
Change input buttons
Changes to images from each input port.
s "Switching to the Target Image by Remote Control"
p.39
The [HDBaseT] button and the [SDI] button are not
available for this projector.
D
[Auto] button
If pressed while projecting analog RGB signals from the
Computer port or the BNC port, you can automatically
optimize Tracking, Sync., and Position.
E
[Aspect] button
Each time the button is pressed, the aspect mode changes.
s "Changing the Aspect Ratio of the Projected Image "
p.45
F
[Test Pattern] button
Displays a test pattern.
s "Displaying a Test Pattern" p.21
G
[Freeze] button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.57
H
[Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.71
I
[ ][ ][ ][ ]
buttons
When the Configuration menu or the Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s "Using the Configuration Menu" p.71
When using the optional wireless mouse receiver,
pressing these buttons moves the pointer.
s "Optional Accessories" p.137
Name Function
J
[ ] button
When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s "Using the Configuration Menu" p.71
Acts as a mouse's left button when using the optional
wireless mouse receiver.
s "Optional Accessories" p.137
K
[Split] button
Each time the button is pressed, the image changes
between projecting two images simultaneously by
splitting the projected screen, or projecting one image as
normal.
s "Projecting Two Images Simultaneously (Split Screen)
" p.53
L
[Page] buttons
[
[
][
]
]
Moves to the previous or next image file when projecting
images from a computer connected via a network.
M
[Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.39
N
[User1] button
[User2] button
[User3] button
Select any frequently used item from the eight available
Configuration menu items, and assign it to one of these
buttons. By pressing the button, the assigned menu item
selection/adjustment screen is displayed, allowing you to
make one-touch settings/adjustments.
s "Settings Menu" p.77
O
Numeric buttons
Enter the Password.
s "Setting Password Protection" p.65
Use this button to enter numbers in Network settings
from the Configuration menu.
P
[ID] button
Hold down this button and press the numeric buttons to
select the ID for the projector you want to operate using
the remote control.
s "ID Settings" p.25
Part Names and Functions
13
Name Function
Q
[ID] switch
Use this switch to enable (On)/disable (Off) ID settings for
the remote control.
s "ID Settings" p.25
R
Remote port
Connects the optional remote control cable set and
outputs signals from the remote control.
s "Optional Accessories" p.137
When the remote control cable is plugged into this remote
port, the remote control light-emitting is disabled.
S
[Help] button
Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.94
T
[Num] button
Hold down this button and press the numeric buttons to
enter passwords and numbers.
s "Setting Password Protection" p.65
U
[E-Zoom] buttons
[
z
][
x
]
Enlarges or reduces the image without changing the
projection size.
s "Enlarging Part of the Image (E-Zoom)" p.57
V
[Default] button
Enabled when [Default]: Reset is displayed on the
configuration menu guide. The settings being adjusted are
returned to their default values.
s "Using the Configuration Menu" p.71
W
[Esc] button
Stops the current function.
If pressed when the Configuration menu is displayed, it
moves to the previous level.
s "Using the Configuration Menu" p.71
Acts as a mouse's right button when using the optional
wireless mouse receiver.
s "Optional Accessories" p.137
X
[A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.56
Name Function
Y
[Color Mode] button
Each time the button is pressed, the Color Mode changes.
s "Selecting the Projection Quality (Selecting Color
Mode)" p.44
Z
[Search] button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
a
[ ] button
Illuminates the buttons on the remote control for
approximately 15 seconds. This is useful when using the
remote control in the dark.
b
Indicator
A light is emitted when outputting remote control signals.
c
Remote control light-
emitting area
Outputs remote control signals.
Replacing the remote control batteries
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two AA size alkaline or manganese batteries ready. You
cannot use other batteries except for the AA size alkaline or manganese.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions
a
Remove the battery cover.
While pushing the battery compartment cover catch, lift the cover
up.
Part Names and Functions
14
b
Replace the old batteries with new batteries.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
If the batteries are not used correctly, they could explode or leak causing
a fire, injury, or damage to the product.
c
Replace the battery cover.
Press the battery compartment cover until it clicks into place.
Remote control operating range
Part Names and Functions
15
a
To restrict reception of the operation signals from the remote
control, set Remote Receiver.
s Settings - Remote Receiver p.77
When using a remote control provided with other Epson projectors,
set the Remote Control Type.
s Extended - Operation - Remote Control Type p.78
The operating range depends on the remote control that you use.
Part Names and Functions
16
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installation Requirements
The projector supports the following four different projection methods.
Install the projector according to the conditions of the installation location.
Project images from in front of
the screen. (Front projection)
Project images from behind a
translucent screen. (Rear projec‐
tion)
Suspend the projector from the
ceiling and project images from
in front of a screen. (Front/Ceil‐
ing projection)
Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
Warning
A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If installation work is not carried out
correctly, the projector could fall down. This may result in injury or
accidents.
Contact your dealer or the nearest address provided in the Support and
Service Guide if you want to use this installation method. s Epson Projector
Contact List
If you use adhesives on the Ceiling mount fixing points to prevent the screws
from loosening, or if you use things such as lubricants or oils on the
projector, the projector case may crack causing it to fall from its ceiling
mount. This could cause serious injury to anyone under the ceiling mount
and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
Attention
Do not use the projector on its side. This may cause malfunctions to occur.
Installing the Projector
18
a
An optional ceiling mount is required when suspending the
projector from a ceiling.
s "Optional Accessories" p.137
The default Projection setting is Front. You can change from Front
to Rear from the Configuration menu.
s Extended - Projection p.78
You can change the Projection mode as follows by pressing down
the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
When mounted on a ceiling, set Inv Direction Button to On so that
the operations and movement of the [
], [ ], [ ], and [ ]
buttons on the control panel match.
s Extended - Operation - Inv Direction Button p.78
The projector can be installed at the following angles.
Vertical: Tilt up to ±30°. If you use the projector tilted at an angle of more
than 30° it could be damaged and cause an accident.
30
30
30
30
Horizontal: Can be tilted within the range of expansion and contraction for
the rear feet.
s "Adjusting the Horizontal Tilt" p.24
Make sure there is a gap of at least 50 cm between the wall and the air
exhaust vent and the air intake vent.
Air exhaust vent
Air intake vent
When setting up multiple projectors, make sure there is a gap of at least
50 cm between the projectors.
Screen Settings
Set the Screen Type according to the aspect ratio of the screen being used.
The area where the image is displayed matches the shape of the screen.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Display from Extended.
Installing the Projector
19
c
Select Screen Type from Screen.
d
Select the screen's aspect ratio.
The shape of the background test pattern changes depending on the
setting.
e
Press the [Menu] button to finish making settings.
a
This setting is unavailable when projecting images from a computer
over a network.
When you change the Screen Type, adjust the aspect ratio for the
projected image as well.
s "Changing the Aspect Ratio of the Projected Image " p.45
Make sure you install the EasyMP Network Projection application
from the EPSON Projector Software CD-ROM. When using an older
version of the application, images are not projected correctly. You
can download the latest version of EasyMP Network Projection from
the following Web site.
http://www.epson.com/
This function does not support Message Broadcasting (an EasyMP
Monitor plugin).
Adjusting the position of the image on the projected screen
You can adjust the position of the image if there are margins between the
edge of the image and the projected screen frame due to the Screen Type
setting.
Example: When the Screen Type is set to 4:3 for EB-4950WU
You can move the image to the left and right.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Display from Extended.
c
Select Screen Position from Screen.
d
Use the [ ], [ ], [ ], and [ ] buttons to adjust the position of
the image.
You can check the current display position by using the background
test pattern.
Installing the Projector
20
e
Press the [Menu] button to finish making settings.
a
The Screen Position cannot be adjusted in the following situations.
If the Screen Type is set to 16:10 when using EB-4955WU/
EB-4950WU/EB-4855WU/EB-4850WU/EB-4750W
If the Screen Type is set to 4:3 when using EB-4650/EB-4550
Displaying a Test Pattern
A test pattern can be displayed to adjust the projection status without
connecting video equipment.
The shape of a test pattern is according to the setting of Screen Type. Set
Screen Type first.
s "Screen Settings" p.19
a
Press the [Test Pattern] button on the remote control or the [ ]
button on the control panel while projecting.
b
Press the [ ][ ] buttons on the remote control or the [ ] button
on the control panel to change the test pattern.
Using the remote control Using the control panel
The following image adjustments can be made while the test pattern
is being displayed.
Top Menu Name Sub Menu/Items
Image
Color Mode s p.44
Abs. Color Temp.
Advanced
- Gamma
*
s p.49
- RGB
- RGBCMY s p.48
Reset
Signal
Auto Setup
Installing the Projector
21
Top Menu Name Sub Menu/Items
Settings
Geometric Correction s p.40
Extended
Multi-Projection
- Multi-screen s p.50
* Except for custom settings of gamma
a
To set menu items that cannot be set while the test pattern is
being displayed or to fine-tune the projected image, project an
image from the connected device.
c
Press the [Esc] button to close the test pattern.
Adjusting the Position of the Projected Image
(Lens Shift)
The lens can be shifted to adjust the position of the projected image, for
example, when the projector cannot be installed directly in front of the
screen.
a
Release the lens shift dial lock.
b
Turn the vertical and horizontal lens shift dials on the projector to
adjust the position of the projected image.
Attention
When adjusting the image height with the vertical lens shift dial, adjust
by moving the image from the bottom to the top. If it is adjusted from
the top to the bottom, the image position may move down slightly
after adjusting.
a
We recommend setting the focus, zoom, and lens shift at least
30 minutes after you start the projection, because images are
not stable right after turning on the projector.
The image will be clearest when both the vertical and
horizontal lens shift are set in the center.
The ranges within which the image can be moved are shown below.
Installing the Projector
22
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU
A
Center of lens
B
Projected image when lens shift is set in the center
EB-4750W/EB-4650/EB-4550
A
Center of lens
B
Projected image when lens shift is set in the center
The position of the projected image cannot be moved to both the
horizontal and vertical maximum values.
c
When you have finished making adjustments, lock the lens shift
dial lock.
Installing the Projector
23
Adjusting the Image Size
Turn the zoom ring to adjust the size of the projected image.
W T
Correcting the Focus
You can correct the focus using the focus ring.
Adjusting the Image Position
Extend or retract the front foot to make adjustments. You can adjust the
position of the image by tilting the projector up to 10 degrees.
A
Extend the front foot.
B
Retract the front foot.
a
The larger the angle of tilt, the harder it becomes to focus. Install the
projector so that it only needs to be tilted at a small angle.
Adjusting the Horizontal Tilt
Extend and retract the rear feet to adjust the projector's horizontal tilt.
A
Extend the rear foot.
B
Retract the rear foot.
Installing the Projector
24
ID Settings
When an ID is set for the projector and the remote control, you can use
the remote control to operate only the projector with a matching ID. This
is very useful when managing multiple projectors.
a
Operation using the remote control is possible only for projectors
that are within the operating range of the remote control.
s "Remote control operating range" p.15
When Remote Control Type is set to Simple from Operation in the
configuration menu, you cannot set the remote control ID.
s p.78
IDs are ignored when the projector ID is set to Off or the remote
control ID is set to 0.
Set the projector ID
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Multi-Projection from Extended.
c
Select Projector ID, and then press the [ ] button.
d
Select the ID you want to set, and then press the [ ] button.
e
Press the [Menu] button to close the configuration menu.
Checking the Projector ID
During projection, press the [Help] button while holding the [ID] button.
Remote control
When you press the buttons, the current Projector ID is displayed on the
projection screen. It disappears in about three seconds.
Setting the remote control ID
a
Set the remote control [ID] switch to On.
Installing the Projector
25
b
While holding the [ID] button, press a number button to select a
number to match the ID of the projector you want to operate.
s "Checking the Projector ID" p.25
Remote control
Once this setting has been made, the projector that can be operated by the
remote control is limited.
a
The remote control ID setting is saved in the remote control. Even if
the remote control batteries are removed to replace them and so on,
the stored ID setting is retained. However, if the batteries are left out
for a long time, it is reset to the default value (ID0).
Setting the Time
You can set the time for the projector. The set time is used by the schedule
function.
s "Scheduling Function" p.62
a
When you turn on the projector for the first time, the message "Do
you want to set the time?" is displayed. When you select Yes, the
screen from step 4 is displayed.
When Time/Schedule Protection is set to On in Password
Protection, settings related to the date and time cannot be changed.
You can make changes after setting Time/Schedule Protection to
Off.
s "Managing Users (Password Protection)" p.65
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Operation from Extended.
c
Select Date & Time, and then press the [ ] button.
d
Make settings for the date and time.
Use the soft keyboard to enter the date and time.
s
"Soft keyboard operations" p.83
Installing the Projector
26
Date & Time
Submenu Function
Date
Set today's date.
Time
Set the current time.
Time Difference (UTC)
Set the time difference from Coordinated
Universal Time.
Set
The settings made in Date & Time are applied.
Daylight Saving Time
Submenu Function
Daylight Saving Time
Set whether or not (On/Off) to activate the
daylight saving time.DST Adjustment (min)
adjusts the time difference between the standard
time and the daylight saving time.
DST Start
Set the date and time to start the daylight saving
time.
DST End
Set the date and time to end the daylight saving
time.
Set
The settings made in Daylight Saving Time are
applied.
Internet Time
Submenu Function
Internet Time
Set to On to update the time automatically through
an Internet time server.
Internet Time Server
Input the IP address for an Internet time server.
Set
The settings made in Internet Time are applied.
a
When changing settings, make sure you select Set, and then
press the [
] button.
e
Press the [Menu] button to finish making settings.
Installing the Projector
27
The port name, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A
When using the supplied computer cable
Connect the computer's display output port to the projector's Computer port.
You can output audio from the projector's speaker by connecting the audio output port on the computer to the projector's Audio1 port using a commercially available audio cable.
B
When using a commercially available 5BNC cable
Connect the computer's display output port to the projector's BNC port.
You can output audio from the projector's speaker by connecting the audio output port on the computer to the projector's Audio2 port using a commercially available audio cable.
C
When using a commercially available HDMI cable
Connect the HDMI port on the computer to the projector's HDMI port.
You can send the computer's audio with the projected image.
D
When using a commercially available DisplayPort cable
Connect the computer's DisplayPort to the projector's DisplayPort.
You can send the computer's audio with the projected image.
Connecting Equipment
28
4
DisplayPort DisplayPort OUT
Computer
Audio1
Audio2
HDMI OUTHDMI
BNC
4
a
Change the audio output from Audio Settings.
s Extended - A/V Settings - Audio Settings p.78
If audio is not sent using an HDMI or DisplayPort cable, connect a commercially available audio cable to the Audio3 port to send the audio. Set HDMI Audio
Output or DisplayPort Audio Output to Audio3.
s Extended - A/V Settings - Audio Settings - HDMI Audio Output, DisplayPort Audio Output p.78
Some commercially available DisplayPort cables come with a lock. When removing the cable, press the button on the cable's connector section and pull out the
cable.
Connecting Equipment
29
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A
When using a commercially available video cable
Connect the video output port on the image source to the projector's Video port.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio
cable.
B
When using a commercially available S-video cable
Connect the S-video output port on the image source to the projector's S-Video port.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio
cable.
C
When using an optional component video cable (D-sub/component converter)
s "Optional Accessories" p.137
Connect the component output port on the image source to the projector's Computer port.
You can output audio from the projector's speaker by connecting the audio output port on the video equipment to the projector's Audio1 port using a commercially available audio
cable.
D
When using a commercially available component video cable (RCA) and a BNC/RCA adapter
Connect the component output port on the video equipment to the projector's BNC port (R/Cr/Pr, G/Y, B/Cb/Pb).
You can output audio from the projector's speaker by connecting the audio output port on the video equipment to the projector's Audio2 port using a commercially available audio
cable.
E
When using a commercially available HDMI cable
Connect the HDMI port on the image source to the projector's HDMI port.
You can send the image source's audio with the projected image.
Connecting Equipment
30
5
4
Computer
Audio1
Video
Video
S-Video
S-Video
Audio-L/R
AUDIO OUT (L,R)
AUDIO OUT (L,R)
AUDIO OUT
AUDIO OUT
Y
Cb/Pb
Cr/Pr
Y
Cb/Pb
Cr/Pr
Audio2
HDMI
HDMI OUT
BNC(R/Cr/Pr, G/Y, B/Cb/Pb)
5
Audio-L/R
4
Attention
If the input source is on when you connect it to the projector, it could cause a malfunction.
If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
Connecting Equipment
31
a
Change the audio output from Audio Settings.
s Extended - A/V Settings - Audio Settings p.78
If audio is not sent using an HDMI cable, connect a commercially available audio cable to the Audio3 port to send the audio. Set HDMI Audio Output to
Audio3.
s Extended - A/V Settings - Audio Settings - HDMI Audio Output p.78
If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker.
A
When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B
When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
Monitor Out D-Sub
Audio Out Audio IN
Connecting Equipment
32
a
Make the following settings to output image and audio even when the projector is in standby mode.
Set Standby Mode to Communication On.
s
Extended - Standby Mode p.78
Set A/V Output to Always On.
s Extended - A/V Settings - A/V Output p.78
When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external
output.
Connecting a LAN Cable
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN
cable.
By connecting a computer to the projector over a network, you can project images and check the status of the projector.
LAN
The position of the LAN port differs depending on the model being used. s "Interface" p.9
a
To prevent malfunctions, use a category 5 or higher shielded LAN cable.
Connecting Equipment
33
Installing the Wireless LAN Unit
a
Open the air filter cover.
Slide the air filter cover operation knob, and open the air filter
cover.
b
Loosen the screw and remove the wireless LAN unit cover.
c
Install the Wireless LAN unit.
d
Secure the wireless LAN unit cover in place with the screw.
Connecting Equipment
34
e
Close the air filter cover.
Attaching the Cable Cover
By attaching the cable cover, you can hide the connected cables giving a
nice, clean finish to the projector installation. (The illustrations are of a
projector installed on a ceiling.)
Attaching
a
Bundle the cables together with a commercially available tie.
b
Attach the cable cover to the rear of the projector.
c
Tighten the screw on the cable cover. (You can tighten the screws
with your fingers.)
Connecting Equipment
35
Connecting Equipment
36
Basic Usage
This chapter explains how to project and adjust images.
Automatically Detect Input Signals and Change
the Projected Image (Source Search)
Press the [Search] button on the remote control or the [Source Search]
button on the control panel to project images from the port currently
receiving an image.
Using the remote control Using the control panel
When two or more image sources are connected, press the [Search] button
on the remote control or the [Source Search] button on the control panel
until the target image is projected.
When your video equipment is connected, start playback before beginning
this operation.
a
The following screen is displayed while no image signals are input.
Projecting Images
38
Switching to the Target Image by Remote Control
You can change directly to the target image by pressing the following
buttons on the remote control.
The input ports for each button are shown below.
Remote control
Input Port
E
Changes to images from a computer connected via the network. See the following
section to check the position of the LAN port.
s "Interface" p.9
Adjusting the Volume
You can adjust the volume using one of the following methods.
Press the [Volume] button on the remote control to adjust the volume.
[
a] Decreases the volume.
[
b] Increases the volume.
Remote control
Adjust the volume from the Configuration menu.
s Settings - Volume p.77
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume
before powering off, so that you can power on and then gradually increase the
volume.
Projecting Images
39
Correcting Distortion in the Projected Image
You can correct keystone distortion in projected images using one of the
following methods.
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently.
s "H/V-Keystone" p.40
Quick Corner
Manually correct the four corners independently.
s "Quick Corner" p.41
Arc Correction
Fine adjustment of the curved distortion caused by slack or shrinkage of
the screen.
s "Arc Correction" p.42
Point Correction
Fine adjustment of small distortions.
s "Point Correction" p.43
a
By pressing the [ ] button on the control panel, you can perform
the selected adjustment method directly.
You cannot combine multiple adjustment methods.
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions
independently. Distortion can be corrected when the angle of vertical and
horizontal tilt of the projector is up to 30 degrees against the screen.
a
Press the [Menu] button while projecting.
b
Select Geometric Correction from Settings.
Adjusting Projected Images
40
c
Select H/V-Keystone, and then press the [ ] button.
If the message "If this setting is changed, the image may be
distorted." is displayed, press the [
] button.
d
Use the [ ][ ] buttons to select the correction method, and
then use the [
][ ] buttons to make the corrections.
V-Keystone
H-Keystone
a
When you correct keystone distortion, the projected image may
be reduced.
e
When you are done, press the [Menu] button to exit the correction
menu.
Quick Corner
This allows you to manually correct each of the four corners of the
projected image separately.
a
Press the [Menu] button while projecting.
b
Select Geometric Correction from Settings.
c
Select Quick Corner, and then press the [ ] button.
If the message "If this setting is changed, the image may be
distorted." is displayed, press the [
] button.
d
Use the [ ], [ ], [ ], and [ ] buttons to select the corner you
want to adjust, and then press the [
] button.
Adjusting Projected Images
41
a
If the [Esc] button is pressed for at least 2 seconds, the confirm
default reset screen is displayed.
Select Yes to reset the result of Quick Corner corrections.
e
Use the [ ], [ ], [ ], and [ ] buttons to correct the position of
the corner.
When you press the [
] button, the screen shown in step 4 that
allows you to select the area to be corrected is displayed.
If the message "Cannot adjust any further." is displayed while
adjusting, you cannot adjust the shape any further in the direction
indicated by the gray triangle.
f
Repeat procedures 4 and 5 as needed to adjust any remaining
corners.
g
When you are done, press the [Menu] button to exit the correction
menu.
Arc Correction
a
Press the [Menu] button while projecting.
b
Select Geometric Correction from Settings.
c
Select Arc Correction, and then press the [ ] button.
If the message "If this setting is changed, the image may be
distorted." is displayed, press the [
] button.
d
Use the [ ], [ ], [ ], and [ ] buttons to select the area you
want to adjust, and then press the [
] button.
When selecting a corner, you can adjust the two sides next to the
corner.
a
If the [Esc] button is pressed for at least 2 seconds, the confirm
default reset screen is displayed.
Select Yes to reset the result of Arc Correction.
e
Use the [ ], [ ], [ ], and [ ] buttons to adjust the shape.
Adjusting Projected Images
42
If the triangle in the direction you are adjusting the shape turns gray,
as shown in the screenshot below, you cannot adjust the shape any
further in that direction.
f
Press the [Esc] button to return to the previous screen.
g
Repeat procedures from 4 to 6 as needed to adjust any remaining
parts.
h
When you are done, press the [Menu] button to exit the correction
menu.
Point Correction
Divides the projected image by the grid and corrects the distortion by
moving the point of intersection from side to side and up and down.
a
Press the [Menu] button while projecting.
b
Select Geometric Correction from Settings.
c
Select Point Correction, and then press the [ ] button.
If the message "If this setting is changed, the image may be
distorted." is displayed, press the [
] button.
d
Select Point Correction, and then press the [ ] button.
Point Correction: Performs point correction.
Pattern Color: Select the color of the grid when performing
corrections.
Reset: Resets all corrections for Point Correction to their default
values.
e
Select the number of grid lines (3x3, 5x5, or 9x9), and then press
the [
] button.
f
Use the [ ], [ ], [ ], and [ ] buttons to move to the point you
want to correct, and then press the [
] button.
Adjusting Projected Images
43
g
Use the [ ], [ ], [ ], and [ ] buttons to correct distortion.
To continue to correct another point, press the [Esc] button to
return to the previous screen, and then repeat steps 6 and 7.
a
Each time you press the [ ] button, you can show or hide the
image and the grid.
h
When you are done, press the [Menu] button to exit the correction
menu.
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode Application
Dynamic
Ideal for use in a bright room. This is the brightest
mode.
Presentation
Ideal for making presentations using color materials
in a bright room.
Theatre
Ideal for watching films in a dark room. Gives
images a natural tone.
Photo
*1
Ideal for projecting still pictures, such as photos, in
a bright room. The images are vivid and brought
into contrast.
Sports
*2
Ideal for watching TV programmes in a bright
room. The images are vivid and brought to life.
sRGB
Ideal for images that conform to the
sRGB
g
color
standard.
DICOM SIM
*1
Ideal for projecting X-ray photographs and other
medical images. This produces images with clear
shadows. The projector is not a medical device and
cannot be used for medical diagnosis.
Multi-Projection
Ideal for projecting from multiple projectors.
Minimize the color tone difference between each
projected image.
*1 This can only be selected when inputting RGB signals, or when LAN is
selected as the input source.
*2 This can only be selected when inputting component video signals, or when
the source is Video or S-Video.
Adjusting Projected Images
44
Each time you press the [Color Mode] button, the Color Mode name is
displayed on the screen and the Color Mode changes.
Remote control
a
You can set Color Mode from the Configuration menu.
s Image - Color Mode p.74
Projecting 3D images
(EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only)
By using two projectors, you can project passive 3D images. You need the
following optional items to project and view 3D images. Make sure you
read the notes in the user's guides supplied with the optional items.
Polarizer (ELPPL01)
Passive 3D Glasses (ELPGS02A/ELPGS02B)
s "Optional Accessories" p.137
When projecting 3D images, set 3D Images to On from the Configuration
menu.
s Signal - 3D Setup - 3D Images p.75
The following color modes are available when projecting 3D images. When
projecting using the optional polarizers (ELPPL01), you can view images at
their optimal color tint.
3D Dynamic
3D Presentation
3D Theatre
3D Multi-Projection
a
This projector arranges the direction of polarizing projection for R
(red), G (green), and B (blue). It is not necessary to inverse left and
right eye G (green) image signals.
Changing the Aspect Ratio of the Projected
Image
You can change the Aspect Ratio
g
of the projected image to suit the type,
the ratio of height and width, and the resolution of the input signals.
Available aspect modes vary depending on the Screen Type currently set.
a
Set the Screen Type before changing the aspect ratio.
s "Screen Settings" p.19
Adjusting Projected Images
45
Changing methods
Each time you press the [Aspect] button on the remote control, the aspect
mode name is displayed on the screen and the aspect ratio changes.
Remote control
Aspect Mode Explanation
Auto
Projects in an appropriate aspect ratio based on
information from the signal being input.
Normal
Projects while retaining the aspect ratio of the input image.
4:3
Projects at an aspect ratio of 4:3.
16:9
Projects at an aspect ratio of 16:9.
Full
Projects at the full size of the projected screen.
Zoom
Projects by enlarging the input image to the full width of
the projected screen while retaining the aspect ratio. Areas
that exceed the edges of the projected screen are not
projected.
Native
Projects to the center of the projected screen at the
resolution of the input image. Areas that exceed the edges
of the projected screen are not projected.
a
You can also set the aspect ratio from the Configuration menu.
s Signal - Aspect p.75
If parts of the computer image are missing, set the Resolution
setting to Wide or Normal from the Configuration menu, according
to the resolution of the computer.
s Signal - Resolution p.75
The aspect mode changes as shown in the tables below.
The following colors in screen images in the tables indicate areas that are
not displayed.
: The area where the image is not displayed depending on the screen
type setting.
: The area where the image is not displayed depending on the aspect
mode setting.
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU/EB-4750W
Screen type setting: 16:10
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
16:9
Full
Adjusting Projected Images
46
Aspect Ratio of Input Signal
16:10 16:9 4:3
Zoom
Native
*
*
The image may differ depending on the resolution of the input signal.
Screen type setting: 16:9
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
Full
Zoom
Native
*
* The image may differ depending on the resolution of the input signal.
Screen type setting: 4:3
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
4:3
16:9
Native
*
*
Only computer images and images from the HDMI port. The image may differ
depending on the resolution of the input signal.
EB-4650/EB-4550
Screen type setting: 4:3
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
4:3
16:9
Adjusting Projected Images
47
Aspect Ratio of Input Signal
16:10 16:9 4:3
Native
*
* Only computer images and images from the HDMI port. The image may differ
depending on the resolution of the input signal.
Screen type setting: 16:9
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
Full
Zoom
Native
*
*
The image may differ depending on the resolution of the input signal.
Screen type setting: 16:10
Aspect Ratio of Input Signal
16:10 16:9 4:3
Auto or Normal
Aspect Ratio of Input Signal
16:10 16:9 4:3
16:9
Full
Zoom
Native
*
* The image may differ depending on the resolution of the input signal.
Adjusting the Image
Hue, Saturation, and Brightness Adjustment
The Hue, Saturation, and Brightness for each of the R (red), G (green), B
(blue), C (cyan), M (magenta) and Y (yellow) color components can be
adjusted.
Make settings from the configuration menu.
s Image - Advanced - RGBCMY p.74
Adjusting Projected Images
48
Gamma Adjustment
Adjusts differences in the coloring for the projected image that occurs
depending on the connected device.
Make settings from the configuration menu.
s
Image - Advanced - Gamma p.74
Select and adjust the correction value
s
Image - Advanced - Gamma p.74
When a smaller value is selected, the dark areas of images become brighter,
but the color saturation for lighter areas may become weaker. When a
larger value is selected, you can reduce the overall brightness of the image
to make the image sharper.
If you select DICOM SIM from Color Mode on the Image menu, select the
adjustment value according to the projection size.
If the projection size is 120 inches or less, select a large value.
If the projection size is 120 inches or more, select a small value.
a
Medical images may not be reproduced correctly according to your
settings and screen specifications.
Adjust while viewing the image
s
Image - Advanced - Gamma - Customized - Adjust it from the image
p.74
Move the cursor on the projected image to the part where you want to
change the brightness, then press the [
] button. Use the [ ][ ] buttons
to adjust the value.
Adjusting Projected Images
49
Adjust using the gamma adjustment graph
s
Image - Advanced - Gamma - Customized - Adjust it from the graph
p.74
Adjust while looking at the gamma adjustment graph.
Correcting the Color Difference when Projecting
from Multiple Projectors
When multiple projectors are lined up and projecting images, you can
correct the brightness and color tone of each projector's image with multi-
screen color adjustment so that the colors of images from each projector
match closely.
a
In some cases the brightness and color tone may not match completely
even after correction.
Summary of correction procedure
When multiple projectors are set up and you need to make corrections, use
the following procedure to correct one projector at a time.
1. Set the projector ID
Set a unique projector ID for the target projector so that you can limit which
projector is being corrected.
s "ID Settings" p.25
2. Correct the color difference.
You can carry out color correction when projecting from multiple projectors.
You can adjust from black to white in five stages called levels 1 to 5, and in
each of these five levels you can adjust the following two points.
Correcting brightness
You can correct the image brightness to make them all equal.
Correcting color
You can correct the image color so that they match closely.
Correcting
a
Press the [Menu] button while projecting.
b
Select Multi-Projection from Extended.
c
Select Multi-screen, and then press the [ ] button.
The following screen is displayed.
Adjusting Projected Images
50
Adjustment Level: There are five levels from white, gray, and up to
black. Adjust each level individually.
Brightness Correct.: Adjust from black to white for each color tone.
Color Correct. (G/R): Adjust the color tone for green and red.
Color Correct. (B/Y): Adjust the color tone for blue and yellow.
d
Select Adjustment Level, and then use the [ ][ ] buttons to set
the adjustment level.
e
Select Brightness Correct., and then use the [ ][ ] buttons to
adjust the brightness.
f
Select Color Correct. (G/R) or Color Correct. (B/Y), and then use
the [
][ ] buttons to adjust the color.
g
Return to step 4 and adjust each level.
h
When you are done, press the [Menu] button to exit the correction
menu.
Adjusting Projected Images
51
Useful Functions
This chapter explains useful tips for giving presentations, and the Security functions.
Projecting Two Images Simultaneously (Split
Screen)
You can simultaneously project images from two sources on the right and
left of the screen.
a
The following input source combinations cannot be projected using
the split screen function.
Computer - BNC, S-Video - Video
Also, when using EB-4955WU/EB-4950WU/EB-4855WU/
EB-4850WU, you cannot project images from the LAN source
(images from a computer over a network) using split screen.
You cannot project the same input source on both sides (left and
right) of the screen.
Operating procedures
Projecting on a split screen
a
Press the [Split] button while projecting.
The currently selected input source is projected on the left of the
screen.
Remote control
a
You can perform the same operations from the configuration
menu.
s Settings - Split Screen p.77
b
Press the [Menu] button.
The Split Screen Setup screen is displayed.
c
Select Source, and then press the [ ] button.
Projection Functions
53
d
Select each input source for Left and Right.
a
You can perform the same operations using the following
procedure.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
s "Switching to the Target Image by Remote Control" p.39
e
Select Execute, and then press the [ ] button.
To switch the source during split screen projection, start the
procedure from step 2.
Switching the left and right screens
Use the following procedure to switch the projected images displayed on
the left and right screens.
a
Press the [Menu] button during split screen projection.
b
Select Swap Screens, and then press the [ ] button.
The projected images on the left and right are swapped.
Switching the left and right image sizes
a
Press the [Menu] button during split screen projection.
b
Select Screen Size, and then press the [ ] button.
c
Select the screen size you want to display, and then press the [ ]
button.
Projection Functions
54
The projected images will appear as shown below after setting the screen
size.
Equal Larger Left
Larger Right
a
You cannot enlarge both the left screen and right screen images at
the same time.
When one image is enlarged, the other image is reduced.
Depending on the video signals that are input, the images on the left
and right may not appear to be the same size even if Equal is
set.
Changing the audio
a
Press the [Menu] button during split screen projection.
b
Select Audio Source, and then press the [ ] button.
c
Select the audio you want to output, and then press the [ ]
button.
When you select Auto, audio is output for the largest screen.
If the screens are the same size, audio is output for the screen on the
left.
Ending the split screen
Press the [Esc] button to end split screen.
The following steps can also be used to end the split screen.
Press the [Split] button on the remote control.
Select Exit Split Screen on the Split Screen Setup screen.
s p.53
Restrictions during split screen projection
Operating restrictions
The following operations cannot be performed during split screen
projection.
Setting the configuration menu
E-Zoom
Changing the aspect mode
Using the [User1], [User2], or [User3] buttons on the remote control
Help can be displayed only when image signals are not input or when
an error or warning notification is displayed.
Projection Functions
55
The user's logo is not displayed.
Restriction relating to images
The default values for the Image menu are applied to the image on the
right screen. However, the settings for the image projected on the left
screen are applied to the image on the right screen for Color Mode,
Abs. Color Temp., and Advanced.
Auto Iris is not available.
s Image - Auto Iris p.74
Hiding the Image and Sound Temporarily (A/V
Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
A/V Mute is applied or released each time you press the [A/V Mute]
button.
Remote control
a
When A/V Mute Release is set to A/V Mute from the configuration
menu, the following operations can still be performed without
releasing A/V mute.
s Extended - Operation - A/V Mute Release p.78
- Change the source with the change input buttons on the remote
control.
s "Switching to the Target Image by Remote Control" p.39
- Control the projector from a computer using communication
commands.
s "Monitoring and Controlling" p.127
A/V mute is only released by pressing the [A/V Mute] button, or by
sending an A/V mute Off command.
When projecting moving images, the images and sound continue to
be played back while A/V Mute is on. It is not possible to resume
projection from the point where A/V Mute was activated.
You can select the screen displayed when the [A/V Mute] button is
pressed from the Configuration menu.
s Extended - Display - A/V Mute p.78
The lamp is still lit during A/V Mute, so the lamp hours continue to
accumulate.
Projection Functions
56
Freezing the Image (Freeze)
When Freeze is activated on moving images, the frozen image continues to
project on the screen, so you can project a moving image one frame at a
time like a still photo. Also, you can perform operations such as changing
between files during presentations from a computer without projecting any
images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
a
Audio does not stop.
When projecting moving images, the images continue to be played
back while the screen is frozen. It is not possible to resume
projection from the point where the screen was frozen.
If the [Freeze] button is pressed while the Configuration menu or
the Help screen is displayed, the menu or the Help screen that is
displayed is closed.
Freeze still works while E-Zoom is being used.
Enlarging Part of the Image (E-Zoom)
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
a
Start E-Zoom.
Press the [
z] button to display the Cross ( ).
Remote control
b
Move the Cross ( ) to the area of the image that you want to
enlarge.
Remote control
Projection Functions
57
c
Enlarge.
Remote control
[z] button: Expands the area each time
it is pressed. You can expand quickly by
holding the button down.
[x] button: Reduces images that have
been enlarged.
[Esc] button: Cancels E-Zoom.
a
During enlarged projection, press the [ ], [ ], [ ], or [ ]
buttons to scroll the image.
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
a
Once a User's Logo has been saved, the logo cannot be returned to the
factory default.
a
Project the image you want to save as the User's Logo, and then
press the [Menu] button.
s "Using the Configuration Menu" p.71
b
Select User's Logo from Extended.
a
When User's Logo Protection from Password Protection is
set to On, a message is displayed and the User's Logo cannot
be changed. You can make changes after setting User's Logo
Protection to Off.
s "Managing Users (Password Protection)" p.65
If User's Logo is selected when Geometric Correction, E-
Zoom or Aspect are being performed, the function currently
being performed is temporarily cancelled.
c
When the message "Choose this image as the User's Logo?" is
displayed, select Yes.
a
When you press the [ ] button, the screen size may change
depending on the signal to match the actual resolution of the
image signal.
d
Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control
panel.
Remote control
a
You can save at 400x300 dots in size.
Projection Functions
58
e
When you press the [ ] button and the message "Select this
image?" is displayed, select Yes.
f
Select the zoom factor from the zoom setting screen.
g
When the message "Save this image as the User's Logo?" is
displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
When a User's Logo is saved, the previous User's Logo is
erased.
Projection Functions
59
The settings for the image currently displayed are saved as a memory,
allowing you to load them when necessary. Settings for the following menu
items are saved in the memory.
Top Menu Submenu
Image
All setting items
Signal
3D Setup
Progressive
Noise Reduction
Mosquito NR
Video Range
Overscan
Image Processing
Settings
Power Consumption
Extended
Multi-Projection
- Multi-screen
Saving/Loading/Erasing the Memory
a
Press the [Menu] button while an image is being displayed.
s "Using the Configuration Menu" p.71
b
Select Memory from Settings.
c
Select the function you want to perform, then press the [ ]
button.
You can only perform Load Memory and Save Memory when an
image is displayed.
Memory Function
60
Function Explanation
Load Memory
Loads the saved memory. When you select a
memory and press the [
] button, the settings
applied to the current image are replaced with the
settings from the memory.
Save Memory
The settings for the image currently displayed are
saved as a memory. When you select a memory
name and press the [
] button, the settings are
saved.
Erase Memory
Erases the registered memory. When you select a
memory name and press the [
] button, a
message is displayed. Select Yes, and then press the
[
] button to erase the selected memory. You can
erase all memories from Reset Memory.
s Reset - Reset Memory p.90
Function Explanation
Rename Memory
Changes the memory name. Select the memory
name you want to change, and then press the [
]
button. Enter the memory name using the soft
keyboard.
s "Soft keyboard operations" p.83
When you have finished, move the cursor over
Finish, and then press the [
] button.
When a memory has already been saved, the memory name and its
color mode are displayed.
a
If the mark on the left of the memory name is turned green, it
means the memory has already been registered. When you
select a registered memory, a message is displayed asking you to
confirm that you want to overwrite the memory. If you select
Yes, the previous settings are deleted and the current settings
are registered.
Memory Function
61
You can schedule turning the projector power on/off and switching the
input source, as events in the schedule. Registered events are executed
automatically at the specified time on the specified dates or weekly.
Warning
Do not place flammable objects in front of the lens. If you set the schedule to
turn on the projector automatically, any flammable objects placed in front of
the lens could cause a fire.
Saving a Schedule
a
You can set or adjust the date and time for the projector in Date &
Time from the configuration menu.
s "Setting the Time" p.26
When Time/Schedule Protection is set to On in Password
Protection, settings related to the scheduling function cannot be
changed. You can make changes after setting Time/Schedule
Protection to Off.
s "Managing Users (Password Protection)" p.65
Setting Methods
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Schedule Settings from Extended.
c
Select Add New from Schedule.
d
Set the schedule.
Submenu Name Function
Event Settings
Select an operation of the projector when the event
is executed. Select No Change for items that you do
not want to change when the event occurs.
You can set the following item operations.
Power
Source
Power Consumption
A/V Mute
Volume
Date / Time Settings
Set the date, day of the week, and time to execute
the event. Use the soft keyboard to enter the date
and time.
s "Soft keyboard operations" p.83
When you have finished, move the cursor over
Finish, and then press the [
] button.
Scheduling Function
62
e
Select Save, and then press the [ ] button.
To register additional schedules, repeat steps 3 to 5.
f
Select Setup complete, and then select Yes to finish saving.
a
A calendar is displayed on the Schedule Settings screen (the screen in
step 3). The indicator turns on when an event is saved. (
: one-time
event;
: periodic event; : communication on/off; : event
invalid)
Use the [
][ ] buttons to highlight and check the schedule
registered for that day.
Editing a schedule
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.71
b
Select Schedule Settings from Extended.
c
Use the [ ][ ] buttons to highlight the date containing the
schedule you want to edit.
d
Highlight the schedule you want to edit, and then press the [Esc]
button.
Scheduling Function
63
a
A repeat icon is displayed for periodic schedules.
e
Perform editing from the menu displayed.
Submenu Name Function
On/Off
Enable or disable the selected schedule. When a
schedule is enabled, the indicator turns green.
Edit
Edit the content of the selected schedule. Select
Save, and then press the [
] button to complete
the editing.
Clear
Deletes the selected schedule.
Add New
Save a new schedule. Select Save, and then press the
[
] button to complete the saving.
f
Select Setup complete, and then select Yes to finish editing.
a
To delete all registered schedules, select Schedule Reset, and
then select Yes. Select Setup complete, and then select Yes to
delete the schedules.
Scheduling Function
64
The projector has the following enhanced security functions.
Password Protection
You can limit who can use the projector.
Control Panel Lock/Remote Control Button Lock
You can prevent people changing the settings on the projector without
permission.
s "Restricting Operation" p.67
Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s "Anti-Theft Lock" p.68
Managing Users (Password Protection)
When Password Protection is activated, people who do not know the
password cannot use the projector to project images even if the projector
power is on. Furthermore, the user's logo that is displayed when you turn
on the projector cannot be changed. This acts as an anti-theft function as
the projector cannot be used even if it is stolen. At the time of purchase,
Password Protection is not activated.
Kinds of Password Protection
The following three kinds of Password Protect settings can be made
according to how the projector is being used.
Power On Protection
When Power On Protection is On, you need to enter a preset password
after the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not
start.
User's Logo Protection
Even if someone tries to change the User's Logo set by the owner of the
projector, it cannot be changed. When User's Logo Protection is set to
On, the following setting changes for the User's Logo are prohibited.
Capturing a User's Logo
Setting Display Background, Startup Screen, or A/V Mute from
Display
s Extended - Display p.78
Network Protection
When Network Protection is set to On, changing the settings for
Network is prohibited.
s
"Network Menu" p.81
Time/Schedule Protection
When Time/Schedule Protection is set to On, changing settings for the
projector's system time or schedules is prohibited.
Setting Password Protection
Use the following procedure to set Password Protect.
a
During projection, hold down the [Freeze] button for about five
seconds.
The Password Protection setting menu is displayed.
Remote control
Security Functions
65
a
If Password Protection is already activated, you must enter the
password.
If the password is entered correctly, the Password Protection
setting menu is displayed.
s "Entering the Password" p.66
b
Select the type of Password Protect you want to set, and then
press the [
] button.
c
Select On, and then press the [ ] button.
Press the [Esc] button to return to the screen in step 2.
d
Set the password.
(1)
Select Password, and then press the [
] button.
(2)
When the message "Change the password?" is displayed, select Yes and
then press the [
] button. The default password is set to "0000". Change
this to your own desired Password. If you select No, the screen displayed
in step 2 is displayed again.
(3) While holding down the [Num] button, enter a four digit number using
the numeric buttons. The number entered is displayed as "* * * *". When
you enter the fourth digit, the confirmation screen is displayed.
Remote control
(4) Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting
you to re-enter the password.
Entering the Password
When the password entry screen is displayed, enter the password using the
remote control.
While holding down the [Num] button, enter the password by pressing the
numeric buttons.
When you enter the correct password, Password Protect is temporarily
released.
Security Functions
66
Attention
If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five
minutes, and then the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet and then reinsert it and
turn the projector's power back on. The projector displays the password entry
screen again so that you can enter the correct password.
If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact the nearest address
provided in the Epson Projector Contact List.
s Epson Projector Contact List
If you continue to repeat the above operation and input the wrong password
thirty times in succession, the following message is displayed and the
projector does not accept any more password entries."The projector's
operation will be locked. Contact Epson as described in your documentation."
s Epson Projector Contact List
Restricting Operation
The following two kinds of operation restriction functions are available with
the projector.
Control Panel Lock
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
Remote control button lock
This function deactivates buttons except for main buttons needed for
basic remote control operation, to prevent mistakes in operations.
Control Panel Lock
Perform one of the following to lock the operation buttons on the control
panel. Even if the control panel is locked, you can still use the remote
control as usual.
Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
Partial Lock
All of the buttons on the control panel, except for the [
t
] button, are
locked.
a
Press the [ ] button on the control panel during projection to
display the Control Panel Lock screen.
a
You can also make settings in Control Panel Lock from the
configuration menu.
s
Settings - Control Panel Lock p.77
b
Select either Full Lock or Partial Lock according to your purpose.
c
Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you
chose.
Security Functions
67
a
You can release the control panel lock by one of the following
two methods.
Use the remote control to set Control Panel Lock to Off
from the configuration menu.
s
Settings - Control Panel Lock p.77
Press and hold down the [
] button on the control panel
for about seven seconds, a message is displayed and the lock
is released.
Remote control button lock
This function locks the following buttons on the remote control.
Each time the [Help] button is pressed for at least 5 seconds, the remote
control button lock turns on or off.
Remote control
a
Even if the remote control button lock is on, the following operations
are possible.
Resetting default for the Remote Receiver setting
Releasing the remote control button lock
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security
devices.
Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Security Functions
68
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
Security Functions
69
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you
can perform the same operations from the control panel. Check the guide
under the menu for the available buttons and their operations.
a
Display the Configuration menu screen.
b
Select a top menu item.
c
Select a submenu item.
d
Change settings.
a
When [Default]: Reset is displayed on the guide, and you press
the [Default] button on the remote control, the settings being
adjusted are returned to their default values.
e
Press the [Menu] button to finish making settings.
Using the Configuration Menu
71
Configuration Menu Table
Settable items vary depending on the model being used and the image
signal and source being projected.
Top Menu Name Submenu Name Items or Setting Values
Image menu
s p.74
Color Mode Dynamic, Presentation, Theatre,
Photo, Sports, sRGB, DICOM
SIM, Multi-Projection, 3D
Dynamic
*
, 3D Presentation
*
, 3D
Theatre
*
, and 3D Multi-
Projection
*
Brightness -24 - 24
Contrast -24 - 24
Color Saturation -32 - 32
Tint -32 - 32
Sharpness -5 to 5, and Advanced
Abs. Color Temp. 5000K to 10000K
Advanced Gamma, RGB, and RGBCMY
Auto Iris Off, Normal, and High Speed
Signal menu
s p.75
Auto Setup On and Off
Resolution Auto, Wide, Normal, Manual
Tracking -
Sync. -
Position -
3D Setup
*
3D Images
Progressive Off, Video, and Film/Auto
Noise Reduction Off, NR1, and NR2
Mosquito NR On and Off
Video Range Auto, Normal, and Expanded
Top Menu Name Submenu Name Items or Setting Values
Input Signal Auto, RGB, and Component
Video Signal Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Aspect Normal, Auto, 4:3, 16:9, Full,
Zoom, and Native
Overscan Auto, Off, 4%, and 8%
Image Processing Fast, Fine
DisplayPort EQ Set‐
ting
1, 2
Settings menu
s p.77
Geometric Correction H/V-Keystone, Quick Corner,
Arc Correction, Point Correction
Split Screen -
Control Panel Lock Full Lock, Partial Lock, and Off
Power Consumption Normal, Temp Interlock, and
ECO
Volume 0 - 20
Remote Receiver Front/Rear, Front, Rear, and Off
User Button User Button 1, User Button 2,
and User Button 3
Test Pattern -
Memory Load Memory, Save Memory,
Erase Memory, Rename Memory
Extended menu
s p.78
Display Menu Position, Messages,
Display Background, Startup
Screen, A/V Mute, Air Filter
Notice, Screen, Panel Alignment,
and Color Uniformity
User's Logo -
List of Functions
72
Top Menu Name Submenu Name Items or Setting Values
Projection Front, Front/Ceiling, Rear, and
Rear/Ceiling
Operation Direct Power On, Sleep Mode,
Sleep Mode Timer, A/V Mute
Timer, High Altitude Mode,
Remote Control Type, Inv
Direction Button, Startup Source
Search, A/V Mute Release, Beep,
and Date & Time
A/V Settings A/V Output, Monitor Out, and
Audio Settings
Standby Mode Communication On and
Communication Off
Multi-Projection Multi-screen and Projector ID
Schedule Settings -
Language 27 languages
Info menu
s p.91
Lamp Hours -
Source -
Input Signal -
Resolution -
Video Signal -
Refresh Rate -
Sync Info -
Status -
Serial Number -
Event ID -
Reset menu
s p.92
Reset All -
Reset Lamp Hours -
Top Menu Name Submenu Name Items or Setting Values
Reset Memory -
*
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only
Network menu
Top Menu Name Submenu Name Items or Setting Values
Basic menu s p.83 Projector Name -
PJLink Password -
Web Control Password -
Projector Keyword On and Off
Wireless LAN menu s
p.84
Wireless LAN Power On and Off
Connection Mode Quick and Advanced
Channel 1ch, 6ch, and 11ch
Wireless LAN system 802.11b/g and
802.11b/g/n
SSID Auto Setting On and Off
SSID -
IP Settings DHCP, IP Address,
Subnet Mask, and
Gateway Address
SSID Display On and Off
IP Address Display On and Off
Security menu s p.85 Security No, WEP, WPA-PSK,
WPA2-PSK
WEP Encryption 128Bit and 64Bit
Format ASCII and HEX
Key ID 1 - 4
Encryption Key 1/2/3/4 -
List of Functions
73
Top Menu Name Submenu Name Items or Setting Values
Authentication Type Open and Shared
Passphrase -
Wired LAN menu s
p.87
IP Settings DHCP, IP Address,
Subnet Mask, and
Gateway Address
IP Address Display On and Off
Mail menu Mail Notification On and Off
SMTP Server -
Port Number -
Address 1 Setting to
Address 3 Setting
Email Address, No Signal,
System Error, Lamp Error,
High Temp Error, Air
Filter Error, Replace
Lamp, High Temp
Warning, Air Filter
Warning, and Air Filter
Notice
Others menu SNMP On and Off
Trap IP Address 1 and
Trap IP Address 2
-
Priority Gateway Wired LAN and Wireless
LAN
AMX Device Discovery On and Off
Crestron RoomView On and Off
Bonjour On and Off
Message Broadcasting On and Off
Image Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.38
Submenu Function
Color Mode
You can select the quality of the image to suit your surroundings.
s "Selecting the Projection Quality (Selecting Color Mode)"
p.44
Brightness
You can adjust the image brightness.
Contrast
You can adjust the difference between light and dark in the
images.
Color Saturation
(Adjustment is only possible when component video or
composite video images are being input.)
You can adjust the color saturation for the images.
List of Functions
74
Submenu Function
Tint
(Adjustment is possible when a component video signal is being
input. If a composite video signal is input, adjustment is only
possible when NTSC signals are being input.)
You can adjust the image tint.
Sharpness
Standard: You can adjust the image sharpness. To make more-
detailed settings, select Advanced.
Advanced: The following four items can be set.
Thin Line Enhancement: If this parameter is set to a positive
value, details such as hair or fabric patterns will be enhanced.
Thick Line Enhancement: If this parameter is set to a positive
value, the outline, background, and the other main parts of the
objects in the image will be enhanced to show them clearly.
Vert. Line Enhancement: If this parameter is set to a positive
value, vertical lines in the image are enhanced.
Horiz. Line Enhancement: If this parameter is set to a positive
value, horizontal lines in the image are enhanced.
Abs. Color Temp.
You can adjust the overall tint of the image. You can adjust tints
in 10 stages from 5000 K to 10000 K. The image is tinted blue
when a high value is selected and tinted red when a low value is
selected.
Advanced
You can make adjustments by choosing the following items.
Gamma: You can adjust the coloring by selecting one of the
gamma correction values, or referring to the projected image or a
gamma graph.
RGB: You can adjust the individual R (red), G (green), and B
(blue) components of the offset and gain.
RGBCMY: You can adjust the hue, saturation, and brightness of
each color R (red), G (green), B (blue), C (cyan), M (magenta), Y
(yellow) individually.
Submenu Function
Auto Iris
(This item can be set only if Color Mode is set to Dynamic,
Theatre, 3D Dynamic or 3D Theatre.)
Set the tracking delay depending on the light intensity correction
for changes in brightness in the image. Light intensity
corrections are not performed when this is set to Off.
The setting is stored for each Color Mode.
Reset
You can reset all adjustment values for the Image menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.92
Signal Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
List of Functions
75
Submenu Function
Auto Setup
(Only available when an analog RGB computer signal is
being input.)
Set to On to automatically adjust Tracking, Sync., and
Position to the optimum state when the input signal
changes.
Resolution
(Only available when an analog RGB computer signal is
being input.)
Set to Auto to automatically identify the resolution of the
input signal. If images are not projected correctly when set
to Auto, for example if some of the image is missing, set to
Wide for wide screens, or set to Normal for 4:3 or 5:4
screens depending on the connected computer.
Manual allows you to specify the resolution. This is ideal
when connected computer is fixed.
Tracking
(Only available when an analog RGB computer signal is
being input.)
You can adjust computer images when vertical stripes
appear in the images.
Sync.
(Only available when an analog RGB computer signal is
being input.)
You can adjust computer images when flickering, fuzziness,
or interference appear in the images.
Position
You can adjust the display position up, down, left, and right
when a part of the image is missing so that the whole image
is projected.
3D Setup
*
When projecting passive 3D images using two projectors, set
3D Images to On.
Progressive
Interlace
g
(i) signal is converted to Progressive
g
(p). (IP
conversion)
Off: Ideal for images with a large amount of movement.
Video: Ideal for general video images.
Film/Auto: This is ideal for movie films, computer graphics,
and animation.
Submenu Function
Noise Reduction
(This cannot be set when Image Processing is set to
Fast.)
Smoothes out the roughness in progressive images. There
are two modes. Select your favorite setting. It is
recommended that this is set to Off when viewing image
sources in which noise is very low, such as for DVDs.
Mosquito NR
(This cannot be set when Image Processing is set to
Fast.)
When a progressive signal is being input, you can reduce
the wavy noise that occurs in lines between areas with
dramatic changes in colors.
Video Range
Select the video range for the input signal from the HDMI
port and the DisplayPort. Set to Expanded if you are
concerned about misadjusted black levels or blown out
highlights in the image.
Input Signal
You can select an input signal from the Computer port or
BNC port.
If set to Auto, the input signal is set automatically
according to the connected equipment.
If colors do not appear correctly when set to Auto, select
the appropriate signal according to the connected
equipment.
Video Signal
You can select an input signal from the Video port or S-
Video port. If set to Auto, video signals are recognized
automatically. If interference appears in the image or a
problem occurs such as no image is being projected when
set to Auto, select the appropriate signal according to the
connected equipment.
Aspect
You can set the
aspect ratio
g
for projected images.
s "Changing the Aspect Ratio of the Projected Image "
p.45
List of Functions
76
Submenu Function
Overscan
(This setting can only be adjusted when a component video
signal is being input.)
Changes the output image ratio (the range of the projected
image). You can set the cropping range to 4% or 8%. When
set to Auto, this is automatically adjusted according to the
input signal.
Image Process-
ing
Changes settings for image processing.
Fast: Images are displayed quicker.
Fine: Images are displayed in higher quality.
DisplayPort EQ
Setting
Adjusts the DisplayPort input signal level depending on the
devices connected to the DisplayPort. If there is a lot of
interference in the image, or if a problem such as no image
being projected occurs, select 1 or 2, and then confirm the
selection.
Reset
You can reset all adjustment values on the Signal menu to
their default settings, except for Input Signal, Image
Processing and DisplayPort EQ Setting.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
* EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only
Settings Menu
Submenu Function
Geometric Cor-
rection
You can correct distortion.
s "Correcting Distortion in the Projected Image" p.40
H/V-Keystone:
Adjust V-Keystone and H-Keystone to correct horizontal
and vertical keystone distortion.
Quick Corner:
Select and correct the four corners of the projected image.
Arc Correction:
Fine adjustment of the curved distortion caused by slack
or shrinkage of the screen.
Point Correction:
Divides the projected image into a grid and corrects the
distortion by moving the selected point of intersection
from side to side and up and down.
Split Screen
You can split the screen into two screens.
s "Projecting Two Images Simultaneously (Split Screen) "
p.53
List of Functions
77
Submenu Function
Control Panel
Lock
You can use this to restrict operation of the projector's
control panel.
s "Control Panel Lock" p.67
Power Con-
sumption
When set to Normal, the lamp is at its brightest.
When set to Temp Interlock, if the surrounding
temperature
*
gets too high, the lamp automatically dims to
control the operating temperature.
When set to ECO, the power consumption during
projection drops and the fan noise is reduced.
Volume
You can adjust the volume. Setting values are saved for each
source.
Remote Receiv-
er
You can limit the reception of the operation signal from the
remote control.
When set to Off, you cannot perform any operations from
the remote control. If you want to make operations from
the remote control, hold down the [Menu] button on the
remote control for at least 15 seconds to reset the setting to
its default value.
User Button
Select the items from the Configuration menu that you want
to assign to the [User1], [User2], and [User3] buttons on
the remote control. The following items can be assigned.
Power Consumption, Info, Progressive, Geometric
Correction, Multi-Projection, Resolution, Memory, or
Image Processing
Test Pattern
You can display a test pattern to adjust the projection
without connecting other equipment when you set up the
projector.
s "Displaying a Test Pattern" p.21
Memory
Perform operations and make settings for the memory
function.
s "Memory Function" p.60
Submenu Function
Reset
You can reset all adjustment values on the Settings menu to
their default settings, except for User Button and
Memory.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
* Operating temperature of +40˚C at an altitude of 0 to 1499 m, and +35˚C at
an altitude of 1500 to 3048 m.
Extended Menu
List of Functions
78
Submenu Function
Display
You can make settings related to the projector's display.
Menu Position: Select the position to display the menu on
the projected screen.
Messages: When set to Off, the following items will not be
displayed.
Item names when the Source, Color Mode, or Aspect is
changed, messages when no signal is being input, and
warnings such as High Temp Warning.
Display Background
*
: You can set the screen background
to Black, Blue, or Logo when no image signal is available.
Startup Screen
*
: Set to On to display the User's Logo when
projection starts.
A/V Mute
*
: You can set the screen displayed when
the [A/V Mute] button is pressed to Black, Blue, or
Logo.
Air Filter Notice: You can set whether or not (On/Off) to
enable Air Filter Notice. When this is set to On and a clog
in the air filter is detected, the message is displayed on the
screen.
Screen: (This setting is unavailable when projecting images
from a computer over a network.) Set the aspect ratio and
position of the projected screen according to the type of
screen being used.
s
"Screen Settings" p.19
Panel Alignment: Correct color misalignments (red and
blue) in the screen.
s "Panel Alignment" p.121
Color Uniformity: Adjusts the color tone balance for the
whole screen.
s "Color Uniformity" p.122
User's Logo
*
You can change the user's logo that is displayed as a
background during Display Background, A/V Mute, and so
on.
s "Saving a User's Logo" p.58
Submenu Function
Projection
Select from one of the following projection methods
depending on how the projector is installed.
Front, Front/Ceiling, Rear, and Rear/Ceiling
You can change the setting as follows by pressing down
the [A/V Mute] button for about five seconds.
FrontWFront/Ceiling
RearWRear/Ceiling
List of Functions
79
Submenu Function
Operation
Direct Power On: Set to On to turn on the projector
simply by plugging it in.
When the power cord is plugged in, note that the projector
turns on automatically in cases such as a power outage
being restored.
Sleep Mode: When set to On, this automatically stops
projection when no image signal is being input and no
operations are carried out.
Sleep Mode Timer: When Sleep Mode is set to On, you
can set the time before the projector automatically turns off
within a range of 1 to 30 minutes.
A/V Mute Timer: When set to On, the projector turns off
automatically after 30 minutes when using A/V mute.
High Altitude Mode: Set to On when using the projector
above an altitude of 1500 m.
Remote Control Type: You can select Normal or Simple
depending on the type of remote control.
Set this item to Normal to use the remote control provided
with this projector. When Simple is selected, you can use
the remote control provided with other Epson projectors to
operate this projector. This is useful if you want to use a
remote control that you are already familiar with to operate
the projector.
However, you cannot use the remote control provided with
this projector if this is set to Simple. Make sure that the
setting is correct because, if the projector is mounted on the
ceiling or somewhere hard to reach, changing it back to
Normal may be difficult. Additionally, you cannot use the
functions that are not equipped with this projector or the
remote control which you use.
Inv Direction Button: Set this to On when the projector is
installed on a ceiling.
Startup Source Search: Set whether or not (On/Off) to
automatically detect the image signal being input when the
projector is turned on.
Submenu Function
A/V Mute Release: (This item cannot be set if User's Logo
Protection from Password Protection is set to On.
s p.65) When set to A/V Mute, you can only release A/V
mute by pressing the [A/V Mute] button (or by sending an
A/V mute Off command). When set to Any Button, A/V
mute is released when any operation is performed on the
projector.
s "Hiding the Image and Sound Temporarily (A/V Mute)"
p.56
Beep: When this is set to On, the confirmation buzzer
beeps to notify you that the power turns on or off, or
cooling down is finished.
Date & Time: Make system time settings for the projector.
s "Setting the Time" p.26
List of Functions
80
Submenu Function
A/V Settings
A/V Output: (This item can be set only if Standby Mode is
set to Communication On) Set this to Always On when the
projector is in standby status and you want to output audio
and images to an external device.
Monitor Out: Select the image source output to an external
monitor when the projector is in standby status. When set
to Auto, analog RGB signals from the Computer port or the
BNC port are output depending on which source was
selected when the projector was turned off.
Audio Settings: Perform the following audio related
settings.
Audio Output: Select the audio to be output when
projecting images from the Computer port, BNC port,
S-Video port or Video port. When set to Auto, audio is
output from the audio input port corresponding to each
image input port.
s "Connecting Equipment" p.28
DisplayPort Audio Output: Select the audio source when
projecting images from the DisplayPort. If you select
DisplayPort, audio for the image is output as it is. If you
select Audio3, audio is output from the Audio3 port.
HDMI Audio Output: Select the audio source when
projecting images from the HDMI port. If you select
HDMI, audio for the image is output as it is.
If you select Audio3, audio is output from the Audio3
port.
Standby Mode
If you set Communication On, you can perform the
following operations even if the projector is in standby
mode.
Monitor and control the projector over a network.
Output audio and images to an external device. (Only
when A/V Output is set to Always On.)
Submenu Function
Multi-Projection
Multi-screen: You can adjust the tint and brightness of each
projected image.
s "Correcting" p.50
Projector ID: Set the ID from 1 to 9.Off indicates that no
ID is set.
s "ID Settings" p.25
Schedule Set-
tings
You can set the projector's schedule so that it performs a
specific operation at a pre-scheduled time.
s "Scheduling Function" p.62
Language
You can set the language for messages and menus.
Reset
You can reset all adjustment values for the Extended menu
to their default settings. However, the following items are
not reset.
Screen Type, Screen Position, Projection, High Altitude
Mode, Remote Control Type, Inv Direction Button,
Startup Source Search, A/V Mute Release, A/V Output,
Monitor Out, Standby Mode, Multi-screen, Projector ID,
and Language
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
* When User's Logo Protection is set to On in Password Protection, settings
related to user's logo cannot be changed. You can make changes after setting
User's Logo Protection to Off.
s "Managing Users (Password Protection)" p.65
Network Menu
When Network Protection is set to On in Password Protection, a message
is displayed and the network settings cannot be changed. Set Network
Protection to Off and then configure the network.
List of Functions
81
s "Setting Password Protection" p.65
Submenu Function
Net. Info. - Wire-
less LAN
Displays the following network setting status information.
Connection Mode
Antenna Level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code
Net. Info. - Wired
LAN
Displays the following network setting status information.
Projector Name
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Submenu Function
Network Config-
uration
The following menus are available for setting Network items.
Basic, Wireless LAN, Security, Wired LAN, Mail, Others, and
Reset
a
By using a Web browser of a computer connected to the projector on
a network, you can set functions and control the projector. This
function is called Web Control. You can easily enter text using a
keyboard to make settings for Web Control such as Security settings.
s "Changing Settings Using a Web Browser (Web Control)"
p.127
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is
the same as making operations from the Configuration menu.
When done, make sure you go to the Setup complete menu, and select Yes,
No, or Cancel. When you select Yes or No, you are returned to the
Configuration menu.
Yes: Saves the settings and exits the Network menu.
No: Does not save the settings and exits the Network menu.
Cancel: Continues displaying the Network menu.
List of Functions
82
Soft keyboard operations
The Network menu contains items that require input of alphanumerics
during setup. In this case, the following software keyboard is displayed. Use
the [
][ ][ ][ ] buttons to move the cursor to the desired key, and
then press the [
] button to enter the selected character. Enter figures by
holding down the [Num] button on the remote control, and pressing the
numeric buttons. After inputting, press Finish on the keyboard to confirm
your input. Press Cancel on the keyboard to cancel your input.
Each time the CAPS key is selected and the [ ] button is pressed, it
sets and changes between upper case and lower case letters.
Each time the SYM1/2 key is selected and the [
] button is pressed, it
sets and changes the symbol keys for the section enclosed by the frame.
The following types of character can be entered.
Numbers
0123456789
Letters
ABCDEFGHIJKLMNOPQRSTUVWXYZ
abcdefghijklmnopqrstuvwxyz
Symbols
! # $ % & ' ( ) + - . / < = > ? @ [ ¥ ] ^ _ { | } ~
a
You cannot use colons (:) for Network menu items.
Except for SSID, you cannot use spaces for Network menu items.
The following four characters cannot be entered using the soft
keyboard. Enter these characters using a Web browser.
* , ;
s
"Changing Settings Using a Web Browser (Web Control)"
p.127
Basic menu
Submenu Function
Projector Name
The projector's name is displayed when using the supplied
application EasyMP Network Projection.
When editing, you can enter up to 16 single-byte alphanumeric
characters.(" * + , / ; < = > ? [ ¥ ] ` | cannot be used.)
List of Functions
83
Submenu Function
PJLink Password
Set a password to use when you access the projector using
compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
(Symbols cannot be used.)
s "About PJLink" p.132
Web Control
Password
Set a password to use Web Remote. You can enter up to 8 single-
byte alphanumeric characters. (* cannot be used)
Web Remote is a computer function that allows you to operate
the projector by using the Web browser on a computer
connected on a network.
s "Changing Settings Using a Web Browser (Web Control)"
p.127
Projector Key-
word
When set to On, you have to enter the keyword when you try to
connect the projector to a computer via a network. As a result,
you can prevent presentations from being interrupted by
connections from other computers.
Normally this should be set to On.
s EasyMP Network Projection Operation Guide
Wireless LAN menu
To connect the projector to a computer using a wireless LAN, install the
Wireless LAN unit (ELPAP07).
s "Installing the Wireless LAN Unit" p.34
Submenu Function
Wireless LAN
Power
Set this to On when connecting the projector and a computer via
a wireless LAN. If you do not want to connect via wireless LAN,
turn it Off to prevent unauthorized access by others.
Connection
Mode
Set the connection mode to use when connecting the projector
and a computer via a wireless LAN.
If you select Quick, a small network is created automatically by
the projector and computer. It is used with EasyMP Network
Projection. If SSID Auto Setting is set to On, the projector
becomes an easy access point; if it is set to Off, the network is
created in
Ad hoc mode
g
. If you select Advanced, the
connection is established in
infrastructure mode
g
through the
access point installed.
Channel
You can select the channels used to connect in Quick mode. If
interference from other signals occurs, use a different channel.
Wireless LAN sys-
tem
Sets the wireless LAN system. Normally this should be set to
802.11b/g/n. The connection method is selected automatically
according to the access point settings.
In an area that does not support 802.11n, only 802.11b/g is
displayed.
List of Functions
84
Submenu Function
SSID Auto Set-
ting
If Connection Mode is set to Quick, when you set this to On, you
can search for the projector more quickly from among multiple
projectors. SSID is set automatically.
When connecting to multiple projectors from 1 computer in
Quick, set this to Off, and set the same SSID in all the projectors
that will connect.
SSID
Enter an SSID. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters. (^
cannot be used. ) Set SSID to blank or ANY to establish an ANY
connection.
IP Settings
DHCP: You can set whether or not (On/Off) to use
DHCP
g
.
If this is set to On, you cannot set any more addresses.
IP Address: You can input the
IP address
g
assigned to the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used. 0.0.0.0,
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Subnet Mask: You can input the
Subnet Mask
g
for the
projector. You can enter a number from 0 to 255 in each field of
the address. However, the following subnet masks cannot be
used.
0.0.0.0, 255.255.255.255
Gateway Address: You can input the IP address for the gateway
for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following
Gateway addresses
g
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
To prevent the SSID from being displayed on the LAN Standby
screen, set this to Off.
IP Address Dis-
play
To prevent the IP address from being displayed on the LAN
Standby screen, set this to Off.
Security menu
When the Wireless LAN unit is installed, it is strongly recommended that
you set security.
List of Functions
85
Submenu Function
Security
You can select a type of security.
When Quick is selected
No: Security is not set.
WPA2-PSK (only when SSID Auto Setting is set to On):
Communication is performed using WPA2 security. Uses
AES method for encryption. When establishing a
connection from a computer to the projector, enter the
value set in the passphrase.
When Advanced is selected
No: Security is not set.
WEP: Connects using an encryption key (WEP key).
Communication is not possible if the encryption key
between the access point and the projector does not
match.
WPA-PSK/WPA2-PSK: Connects in WPA personal mode.
Encryption method is selected automatically according to
the access point settings. Set a passphrase which is the
same for the access point.
Submenu Function
WEP Encryption
Set the encryption method for WEP encryption.
128Bit: Uses 128 (104) bit encryption.
64Bit: Uses 64 (40) bit encryption.
Format
Set the format for the WEP encryption key.
ASCII: Input as text.
HEX: Input in hexadecimal.
Key ID
Select the WEP encryption ID key.
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4
Enter the key to be used for WEP encryption. Enter the key in
single-byte characters according to instructions from the
administrator for the network the projector is going to join. The
type of supported characters and the number of characters
changes depending on the WEP Encryption and Format
settings.
For 128Bit - ASCII: 13 single-byte alphanumeric characters
For 64Bit - ASCII: 5 single-byte alphanumeric characters
For 128Bit - HEX: 26 characters using 0 to 9 and A to F
For 64Bit - HEX: 10 characters using 0 to 9 and A to F
Authentication
Type
Sets the WEP authentication type.
Open: Uses an open system authentication.
Shared: Uses a shared key authentication.
List of Functions
86
Submenu Function
Passphrase
Enter the passphrase. You can enter at least 8 and up to 63 single-
byte alphanumeric characters. When the passphrase is entered
and the [
] button is pressed, the value is set and displayed as an
asterisk (*).
When using it with EasyMP Network Projection, you do not
need to input the passphrase in the computer if it is the initial
(default) passphrase.
It is recommended to change the passphrase periodically for the
purpose of security. If the network settings are initialized, it
returns to the initial passphrase.
s "Reset menu" p.90
You can enter up to 32 characters on the Configuration menu.
When entering more than 32 characters, use your Web browser
to enter the text.
s "Changing Settings Using a Web Browser (Web Control)"
p.127
In Quick mode, the initial passphrase is set.
Wired LAN menu
List of Functions
87
Submenu Function
IP Settings
DHCP: You can set whether or not (On/Off) to use
DHCP
g
.
If this is set to On, you cannot set any more addresses.
IP Address: You can input the
IP address
g
assigned to the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask: You can input the
Subnet Mask
g
for the
projector. You can enter a number from 0 to 255 in each field of
the address. However, the following subnet masks cannot be
used.
0.0.0.0, 255.255.255.255
Gateway Address: You can input the IP address for the gateway
for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following
Gateway addresses
g
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
IP Address Dis-
play
To prevent the IP address from being displayed on the LAN
Standby screen, set this to Off.
Mail menu
When this is set, you receive an email notification if a problem or warning
occurs in the projector.
s "Reading Error Notification Mail" p.128
Submenu Function
Mail Notification
Set to On to send an email to the preset addresses when a problem
or warning occurs with a projector.
SMTP Server
You can input the
IP address
g
for the SMTP server for the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Port Number
You can input the port number for the SMTP server. The default
value is 25. You can input numbers between 1 to 65535.
List of Functions
88
Submenu Function
Address 1 Set-
ting/Address 2
Setting/Address
3 Setting
Enter the destination email addresses to which to send the
notification email, and select the problems or warnings you want
to be notified about. You can register up to three destinations.
You can enter up to 64 single-byte alphanumeric characters for
the email addresses.( " ( ) , ; < > [ ¥ ] cannot be used.)
You can enter up to 32 characters on the Configuration menu.
When entering more than 32 characters, use your Web browser
to enter the text.
s "Changing Settings Using a Web Browser (Web Control)"
p.127
The address for destination 1 is the mail notification sender's
address.
Others menu
Submenu Function
SNMP
Set to On to monitor the projector using
SNMP
g
. To monitor
the projector, you need to install the SNMP manager program on
your computer. SNMP should be managed by a network
administrator. The default value is Off.
Trap IP Address
1/Trap IP Ad-
dress 2
You can register up to two IP addresses for the SNMP trap
notification destination.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Priority Gateway
For the priority gateway, select either Wired LAN or Wireless
LAN.
AMX Device Dis-
covery
When you want to allow the projector to be detected by
AMX
Device Discovery
g
, set this to On. Set this to Off if you are not
connected to an environment controlled by a controller from
AMX or AMX Device Discovery.
List of Functions
89
Submenu Function
Crestron Room-
View
Set this to On only when monitoring or controlling the projector
over the network using Crestron RoomView
®
. Otherwise, set
this to Off.
s "About Crestron RoomView
®
" p.132
Changes in projector settings take effect upon restarting.
When this is set to On, the following functions are not available.
Web control
Message Broadcasting (EasyMP Monitor plugin)
Bonjour
Set this to On when connecting to the network using Bonjour.
See Apple's Web site for more information on the Bonjour
service.
http://www.apple.com/
Message Broad-
casting
You can switch the EPSON Message Broadcasting function to
enable or disable.
You can download Message Broadcasting and its Operation
Guide from the following Web site.
http://www.epson.com
Reset menu
Resets all of the network settings.
Submenu Function
Reset network
settings.
To reset all of the Network settings, select Yes.
After you reset all the settings, the Basic menu appears.
List of Functions
90
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status
of the projector. Items that can be displayed vary depending on the source
currently being projected.
Submenu Function
Lamp Hours
You can display the cumulative lamp operating time
*
.
When the lamp replacement time is reached, the characters
are displayed in yellow.
Source
You can display the source name for the connected
equipment currently being projected.
Input Signal
You can display the content of Input Signal set in the
Signal menu according to the source.
Resolution
You can display the resolution.
Video Signal
You can display the settings for Video Signal in the Signal
menu.
Refresh Rate
You can display the
refresh rate
g
.
Sync Info
You can display the image signal information.
This information may be needed if service is required.
Submenu Function
Status
This is information about errors that have occurred on the
projector.
This information may be needed if service is required.
Serial Number
Displays the projector's serial number.
Event ID
Displays the application error log.
s "About Event ID" p.110
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
and above is displayed as "10H", "11H", and so on.
List of Functions
91
Reset Menu
Submenu Function
Reset All
You can reset all items in the Configuration menu to their default
settings.
The following items are not reset to their defaults: Input Signal,
User's Logo, all items for Network menus, Lamp Hours,
Language, Password, Multi-screen, Date & Time, Panel
Alignment, and Color Uniformity.
Reset Lamp
Hours
Clears the cumulative lamp hours use time. Reset when you
replace the lamp.
Reset Memory
The name and settings saved in Save Memory are reset.
s "Memory Function" p.60
List of Functions
92
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.
If a problem occurs with the projector, the Help screen is displayed to assist
you by pressing the Help button. You can solve problems by answering the
questions.
a
Press the [Help] button.
The Help screen is displayed.
Remote control
b
Select a menu item.
Remote control
c
Confirm the selection.
Remote control
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit the Help.
a
See the following if the Help function does not provide a
solution to the problem.
s "Problem Solving" p.95
Using the Help
94
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
See the following if the indicators do not show clearly what the problem might be.
s "When the Indicators Provide No Help" p.99
Reading the Indicators
The projector is provided with the following four indicators that indicate the operating status of the projector.
A
Power indicator Indicates the operating status.
Standby condition
In this status, you can start projecting by pressing the [
] button on the remote control, or the [
t
] button
on the control panel.
Preparing for network monitoring or cool down in progress
All buttons are disabled while the indicator is flashing.
Problem Solving
95
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [
t
] button is disabled during warm-up.
Projecting
B
Lamp indicator Indicates the projection lamp status.
C
Temp indicator Indicates the internal temperature status.
D
Filter indicator Indicates the air filter status.
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cord is connected correctly and that the power is being supplied normally.
Sometimes, when the power cord is unplugged, the [
t] indicator remains lit for a short period, but this is not a fault.
: Lit : Flashing : Off : Varies according to the projector status
Status Cause Remedy or Status
Internal Error Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
High Temp Error
(Overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby
mode, so check the following two points.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.112
s
"Replacing the Air Filter" p.118
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
96
Status Cause Remedy or Status
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.78
Lamp Error
Lamp Failure
Check the following two points.
Take out the lamp and check if it is cracked.
s "Replacing the Lamp" p.115
Clean the air filter.
s "Cleaning the Air Filter" p.112
If the lamp is not cracked: Reinstall the lamp and turn on the power.
If the error continues: Replace the lamp with a new one and then turn on the power.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If the lamp is cracked: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be
projected until the lamp is replaced.)
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.78
Auto Iris Error
Power Err. (Ballast)
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
Filter Airflow Error Check the following two points.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.112
s "Replacing the Air Filter" p.118
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
97
Status Cause Remedy or Status
High Temp Warning (This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.112
s "Replacing the Air Filter" p.118
Replace Lamp Replace it with a new lamp.
s "Replacing the Lamp" p.115
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a
new lamp as soon as possible.
Low Air Flow Check the following two points.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.112
s "Replacing the Air Filter" p.118
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Air Filter Notice "Time to clean the air filter. Clean or replace the air filter." is displayed. Clean the air filter.
s "Cleaning the Air Filter" p.112
The indicators or messages regarding Air Filter Notice are displayed only when Air Filter Notice is set to On from the Configuration menu.
s Extended - Display - Air Filter Noticep.78
a
See the following if the projector is not operating properly, even though the indicators are all showing normal.
s "When the Indicators Provide No Help" p.99
If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
98
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems Relating to Images
No images appear
Projection does not start, the projection area is completely black,
or the projection area is completely blue.
sp.100
Moving images are not displayed
Videos played back on a computer are black or no image is
projected, or the video is not played back on the computer.
sp.100
Projection stops automatically sp.101
The message "Not supported" is displayed sp.101
The message "No Signal" is displayed sp.101
Images are fuzzy, out of focus, or distorted sp.102
Interference or distortion appear in images sp.102
The image is truncated (large) or small, the aspect ratio is not
suitable, or the image has been reversed
Only part of the image is displayed, the height and width ratios
of the image are not correct, or the image may appear reversed
from top to bottom or left to right.
sp.103
Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
sp.104
Images appear dark sp.105
Problems when projection starts
The projector does not turn on sp.105
Other Problems
No sound can be heard or the sound is faint sp.106
The remote control does not work sp.107
Nothing appears on the external monitor sp.108
I want to change the language for messages and menus sp.108
Email is not received even if a problem occurs in the projector sp.108
"The battery that saves your clock settings is running low." is
displayed
sp.109
Cannot change settings using a Web browser sp.109
Problem Solving
99
Problems Relating to Images
No images appear
Check Remedy
Did you press the [
] button on the remote control or the [t]
button on the control panel?
Press the [ ] button on the remote control or the [t] button on the control panel to turn on the projector.
Are the indicators switched off? The power cord is not connected correctly or power is not being supplied.
Connect the projector's power cord correctly.
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active? Press the [A/V Mute] button to release A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.56
Are the Configuration menu settings correct? Reset all of the settings.
s Reset - Reset All p.92
Is the image to be projected completely black?
(Only when projecting computer images)
Some input images, such as screen savers, may be completely black.
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.75
Is Windows Media Center displayed in full screen?
(Only during network connection)
When Windows Media Center is displayed at full screen, you cannot project using a network connection. Reduce the
screen size.
Is an application using the Windows DirectX function displayed?
(Only during network connection)
Applications using the Windows DirectX function may not display images correctly.
Moving images are not displayed
Check Remedy
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Problem Solving
100
Check Remedy
Are the contents of the moving image you are trying to project
copyright protected?
The projector may not be able to project copyright protected moving images that are being played back on a computer.
For more details, see the user's guide supplied with the player.
Projection stops automatically
Check Remedy
Is Sleep Mode set to On?
Press the [
] button on the remote control or the [
t
] button on the control panel to turn on the projector. If you do not
want to use Sleep Mode, change the setting to Off.
s Extended - Operation - Sleep Mode p.78
Is A/V Mute Timer set to On?
Press the [ ] button on the remote control or the [
t
] button on the control panel to turn on the projector. If you do not
want to use A/V Mute Timer, change the setting to Off.
s Extended - Operation - A/V Mute Timer p.78
The message "Not supported" is displayed
Check Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.75
Do the image signal resolution and the refresh rate correspond to the
mode?
(Only when projecting computer images)
Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from
the computer.
s "Supported Monitor Displays" p.144
The message "No Signal" is displayed
Check Remedy
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
Check that no cables are disconnected and that there are no poor contacts in the cables.
Is the correct port selected? Press the [Search] button or the [Source Search] button to change the image.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.38
Problem Solving
101
Check Remedy
Is the power for the computer or video source turned on? Turn the power on for the equipment.
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
If the image signals are only being output to the computer's LCD monitor or to the accessory monitor, you need to
change the output to an external destination as well as the computer's own monitor. For some computer models, when
the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key)
that changes the computer's image signal to external output may not work. Turn the power for the computer and the
projector off and then back on again.
s Computer's documentation
Images are fuzzy, out of focus, or distorted
Check Remedy
Is the focus adjusted correctly? Turn the focus ring to adjust the focus.
s "Correcting the Focus" p.24
Is the projector at the correct distance? Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.
s
"Screen Size and Projection Distance" p.138
Has condensation formed on the lens? If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature
changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the
projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and
wait for the condensation to disappear.
Interference or distortion appear in images
Check Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.75
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
s "Connecting Equipment" p.28
Is an extension cable being used? If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to
check if the cables you are using may be causing the problem.
Problem Solving
102
Check Remedy
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.144
s Computer's documentation
Are the
Sync.
g
and Tracking
g
settings adjusted correctly?
(Only when projecting computer images)
Press the [Auto] button on the remote control or the [
] button on the control panel to perform automatic adjustment.
If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments
from the Configuration menu.
s
Signal - Tracking, Sync. p.75
Is the Resolution set to anything other than Auto?
(Only when projecting on a split screen)
The image may be collapsed if the Resolution on the Configuration menu and the resolution of the projected image are
not the same.
If the image is collapsed, set the Resolution to Auto.
s Signal - Resolution p.75
The image is truncated (large) or small, the aspect is not suitable, or the image has been reversed
Check Remedy
Have the Screen Type and Screen Position been set correctly? Make the appropriate Screen Type and Screen Position settings for the screen being used.
s "Screen Settings" p.19
Is the aspect adjusted correctly? Press [Aspect] button, and then select the aspect according to the input signal.
s "Changing the Aspect Ratio of the Projected Image " p.45
Is a wide panel computer image being projected?
(Only when projecting computer images)
Change the setting according to the signal for the connected equipment.
s Signal - Resolution p.75
Is the image still being enlarged by E-Zoom? Press the [Esc] button on the remote control to cancel E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.57
Is the image position adjusted correctly? (Only when projecting analog RGB signals input from the Computer port)
Press the [Auto] button on the remote control or the [
] button on the control panel to adjust the position.
You can also adjust the position from the Configuration menu.
s
Signal - Position p.75
Is the computer set for dual display?
(Only when projecting computer images)
If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the
computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
s Computer video driver documentation
Problem Solving
103
Check Remedy
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.144
s Computer's documentation
Is the image direction correct? Make the correct settings in Projection from the Configuration menu.
s "Installation Requirements" p.18
Image colors are not right
Check Remedy
Do the input signal settings match the signals from the connected
device?
Change the following settings according to the signal for the connected equipment.
When the image is from a device connected to the Computer port or the BNC port
s Signal - Input Signal p.75
When the image is from a device connected to the Video port or the S-Video port
s Signal - Video Signal p.75
Is the image brightness adjusted correctly? Adjust the Brightness setting from the Configuration menu.
s Image - Brightness p.74
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
Check that no cables are disconnected and that there are no poor contacts in the cables.
s "Connecting Equipment" p.28
Is the
contrast
g
adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.74
Is the color adjustment set correctly? Adjust the Gamma, RGB, or RGBCMY setting from the Configuration menu.
s Image - Advanced p.74
s
"Adjusting the Image" p.48
Are the color saturation and tint adjusted correctly?
(Only when projecting images from a video source)
Adjust the Color Saturation and Tint settings from the Configuration menu.
s Image - Color Saturation, Tint p.74
Problem Solving
104
Images appear dark
Check Remedy
Is the image brightness set correctly? Check the Brightness and Power Consumption settings from the Configuration menu.
s Image - Brightness p.74
s
Settings - Power Consumption p.77
Is the
contrast
g
adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.74
Is it time to replace the lamp? When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When
this happens, replace the lamp with a new lamp.
s "Replacing the Lamp" p.115
Has the projector been left unattended without an image signal being
input?
If no operations are performed on the projector while no image signal is being input, the lamp is automatically dimmed
to prevent electricity being wasted. When an image signal is input or an operation is performed on the projector, the
projector returns to the previous brightness setting.
Is Sleep Mode set to On? If no operations are performed on the projector for approximately five minutes while no image signal is being input, the
lamp is automatically dimmed to prevent electricity being wasted.
Problems when Projection Starts
The projector does not turn on
Check Remedy
Did you press the [
] button on the remote control or the [
t
]
button on the control panel?
Press the [ ] button on the remote control or the [
t
] button on the control panel to turn on the projector.
Are the indicators switched off? The power cord is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cord.
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cord is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this
does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
105
Check Remedy
Is the Control Panel Lock set to Full Lock?
Press the [
] button on the remote control. If you do not want to use Control Panel Lock, change the setting to
Off.
s "Control Panel Lock" p.67
Is the correct setting for the remote receiver selected? Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.77
Was the power cable plugged back in or was the breaker turned on
immediately after Direct Power Off?
When the operation to the left is performed when Direct Power On is set to On, the power may not turn back on. Press
the [
] button on the remote control or the [t] button on the control panel to turn on the projector.
Is the [ID] switch on the remote control set to On? When the switch is set to On, you can use the remote control to operate only a projector with a matching ID. Set the [ID]
switch to Off.
s "Setting the remote control ID" p.25
Are the lamp cover and lamps installed correctly? If the lamp or lamp cover is installed incorrectly, the projector cannot be turned on. Check how it is installed.
s "How to replace the lamp" p.115
Other Problems
No sound can be heard or the sound is faint
Check Remedy
Check that the audio/video cable is securely attached to both the
projector and audio source.
Disconnect the cable from the Audio port, and then reconnect the cable.
Is the projector volume set to the minimum? Adjust the volume so that sound can be heard.
s Settings - Volumep.77
s
"Adjusting the Volume" p.39
Is the volume for the computer or from the image source set to the
minimum?
Adjust the volume so that sound can be heard.
Is A/V Mute active? Press the [A/V Mute] button to release A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.56
Is the audio cable's specification "No resistance"? When using a commercially available audio cable, make sure it is labeled "No resistance".
Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Problem Solving
106
Check Remedy
Is the correct audio input selected? Check the Audio Settings from the configuration menu.
s Extended - A/V Settings - Audio Settings p.78
The remote control does not work
Check Remedy
Is the remote control light-emitting area pointing towards the
remote receiver on the projector during operation?
Point the remote control towards the remote receiver.
s "Remote control operating range" p.15
Is the remote control too far from the projector? The operating range for the remote control is about 15 m.
s "Remote control operating range" p.15
Is direct sunlight or strong light from fluorescent lamps shining onto
the remote receiver?
Set the projector up in a location where strong light does not shine onto the remote receiver.
Is the correct setting for the Remote Receiver selected? Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.77
Are the batteries dead or have the batteries been inserted correctly? Make sure the batteries are inserted correctly or replace the batteries with new ones if necessary.
s "Replacing the remote control batteries" p.14
Are the remote control ID and the projector ID matched? Make sure the ID for the projector you want to operate and the ID for the remote control match. To operate all projectors
by remote control regardless of the ID setting, set the [ID] switch on the remote control to Off.
s "ID Settings" p.25
Does Remote Control Type match the remote control that you are
using?
Check the Remote Control Type on the configuration menu.
s Extended - Operation - Remote Control Type p.78
Is the optional remote control cable connected to the projector's
Remote port?
When the remote control cable is connected, the projector's remote receiver is disabled. When not using the remote
control cable set, disconnect it from the Remote port.
Is the remote control button lock set? When the remote control button lock is set, buttons except for those needed for basic remote control operations are
deactivated. Hold down the [Help] button to cancel the remote control button lock.
s "Remote control button lock" p.68
Problem Solving
107
Nothing appears on the external monitor
Check Remedy
Are images input from a port other than the Computer port or
BNC port?
Only RGB signals from the Computer port or the BNC port can be displayed on an external monitor.
Are you projecting a split screen? Only RGB signals projected on the left screen from the Computer port or the BNC port can be displayed on an
external monitor.
s "Projecting Two Images Simultaneously (Split Screen) " p.53
Is the projector in standby status? Check that Standby Mode, A/V Output, and Monitor Out from the Configuration menu are set correctly.
s Extended - Standby Mode p.78
s Extended - A/V Settings p.78
I want to change the language for messages and menus
Check Remedy
Change the Language setting. Adjust the Language setting from the Configuration menu.
s Extended - Languagep.78
Email is not received even if a problem occurs in the projector
Check Remedy
Is Standby Mode set to Communication On? To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from
the Configuration menu.
s Extended - Standby Mode p.78
Did a fatal abnormality occur and the projector come to a sudden
stop?
When the projector comes to a sudden stop, email cannot be sent.
If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact
List.
s Epson Projector Contact List
Is power being supplied to the projector? Check that your electrical outlet or power source is functioning correctly.
Is the Mail Notification function set correctly in the Configuration
menu?
An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
s "Mail menu" p.88
Problem Solving
108
"The battery that saves your clock settings is running low." is displayed
Check Remedy
The internal power supply that saves your clock settings is
running low.
Contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Cannot change settings using a Web browser
Check Remedy
Are the user ID and password correct? Enter "EPSONWEB" as the user ID. This cannot be changed. Enter the user ID even if the password setting is
disabled.
Enter the characters set for the Web Control Password as the password. The default password is "admin".
Problem Solving
109
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Event ID Cause Remedy
0432
0435
Failed to startup EasyMP Network Projection. Restart the projector.
0434
0481
0482
0485
Network communication is unstable. Check the network communication status, and reconnect after waiting for a
while.
0433 Cannot play transferred images. Restart EasyMP Network Projection.
0484 Communication was disconnected from the computer.
04FE EasyMP Network Projection ended unexpectedly. Check the status of network communications. Restart the projector.
04FF A system error occurred in the projector. Restart the projector.
0891 Cannot find an access point with the same SSID. Set the computer, the access point, and the projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Check that the wireless LAN security settings are correct.
s "Security menu " p.85
0893 The WEP/TKIP/AES encryption type does not match.
0894 Communication was disconnected because the projector connected to an
unauthorized access point.
Contact your network administrator for more information.
0898 Failed to acquire DHCP. Check the DHCP server to see if it is operating correctly and check the LAN
cable to see if it is connected correctly. If you are not using DHCP, turn off the
DHCP setting.
s"Network Menu" p.81
0899 Other communication errors If restarting the projector or EasyMP Network Projection does not solve the
problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
About Event ID
110
Maintenance
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Caution
When cleaning, unplug the power cable from the electric outlet. Otherwise, it
could cause an electric shock.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing
a small amount of neutral detergent, and then firmly wring the cloth dry
before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the
projector's surface. The quality of the case may change or become discolored.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the
lens.
Warning
Do not use sprays that contain flammable gas to remove dust and lint from the
lens. The projector may catch fire due to the high internal temperature of the
lamp.
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it
can easily become damaged.
Cleaning the Air Filter
When the following message is displayed and the filter indicator flashes
green, clean the air filter and the air intake vent.
"Time to clean the air filter. Clean or replace the air filter."
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter."
"The air filter is clogged. Clean or replace the air filter."
Attention
If dust collects on the air filter, it can cause the internal temperature of the
projector to rise, and this can lead to problems with operation and shorten
the optical engine's service life. Clean the air filter immediately when the
message is displayed.
Do not rinse the air filter in water. Do not use detergents or solvents.
When using a brush for cleaning, use one with long soft bristles, and brush it
lightly. If it is brushed too strongly, dust will be ground into the air filter and
cannot be removed.
Cleaning the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cable.
Cleaning
112
b
Open the air filter cover.
Slide the air filter cover operation knob, and open the air filter
cover.
c
Remove the air filter.
Grip the tab in the center of the air filter, and pull it straight out.
d
With the front (the side with tabs) of the air filter facing down, tap
the air filter four or five times to shake off the dust.
Turn it over and tap the other side in the same way.
Attention
If the air filter is hit too hard, it may become unusable due to
deformities and cracks.
e
Remove any dust remaining on the air filter by using a vacuum
cleaner from the front side.
Cleaning
113
f
Replace the air filter.
Press until it clicks into place.
g
Close the air filter cover.
a
If a message is frequently displayed, even after cleaning, it is time to
replace the air filter. Replace it with a new air filter.
s "Replacing the Air Filter" p.118
It is recommended that you clean these parts at least once every
three months. Clean them more often than this if using the projector
in a particularly dusty environment.
The indicators or messages regarding Air Filter Notice are displayed
only when Air Filter Notice is set to On from the Configuration
menu.
s Extended - Display - Air Filter Notice p.78
Cleaning
114
This section explains how to replace the lamp and the air filter.
Replacing the Lamp
Lamp replacement period
It is time to replace the lamp when:
The following message is displayed.
"It is time to replace your lamp. Please contact your Epson projector
reseller or visit www.epson.com to purchase."
The message is displayed for 30 seconds.
The lamp indicator flashes orange.
The projected image gets darker or starts to deteriorate.
Attention
The lamp replacement message is set to appear after the following time
periods in order to maintain the initial brightness and quality of the projected
images.
When using Power Consumption continually at Normal: About 3900 hours
When using Power Consumption continually at ECO: About 4900 hours
s Settings - Power Consumption p.77
If you continue to use the lamp after the replacement period has passed, the
possibility that the lamp may explode increases. When the lamp replacement
message appears, replace the lamp with a new one as soon as possible, even if
it is still working.
Do not repeatedly turn off the power and immediately back on. Turning the
power on and off frequently may shorten the lamp's operating life.
Depending on the characteristics of the lamp and the way it has been used,
the lamp may become darker or stop working before the lamp warning
message appears. You should always have a spare lamp unit ready in case it is
needed.
We recommend the use of genuine EPSON spare lamps. The use of non-
genuine lamps may affect projection quality and safety. Any damage or
malfunction caused by the use of non-genuine lamps may not covered by
Epson's warranty.
a
We recommend that you clean the air filter whenever you replace
the lamp.
s "Cleaning the Air Filter" p.112
Replace the air filter if it is discolored or if a message appears even
after cleaning the air filter.
s "Replacing the Air Filter" p.118
How to replace the lamp
The lamp can be replaced even when the projector is suspended from a
ceiling.
Replacing Consumables
115
Warning
When replacing the lamp because it has stopped illuminating, there is a
possibility that the lamp may be broken. If replacing the lamp of a projector
which has been installed on the ceiling, you should always assume that the
lamp is cracked, and you should stand to the side of the lamp cover, not
underneath it. Remove the lamp cover gently. Be careful when removing the
lamp cover as shards of glass may fall out and could cause an injury. If any
shards of glass get into your eyes or mouth, contact your local physician
immediately.
Never disassemble or remodel the lamp. If a modified or disassembled lamp
is installed in the projector and used, it could cause a fire, electric shock, or
an accident.
Caution
Wait until the lamp has cooled down sufficiently before removing the lamp
cover. If the lamp is still hot, burns or other injuries may result. It takes about
one hour after the power has been turned off for the lamp to be cool enough.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cord.
b
Wait until the lamp has cooled down, then remove the projector's
lamp cover.
Loosen the Lamp cover fixing screw with the screwdriver supplied
with the new lamp unit or a cross-head screwdriver, and then
remove the lamp cover. Because there is a string attached to the
lamp cover to prevent it from falling, you can replace the lamp even
when the projector is installed on a ceiling without the lamp cover
falling down.
c
Loosen the two lamp fixing screws.
Replacing Consumables
116
d
Take out the old Lamp by pulling the handle.
If the Lamp is cracked, replace it with a new lamp, or contact your
local dealer for further advice.
s Epson Projector Contact List
e
Install the new lamp.
Insert the lamp along the guide rail in the correct direction so that it
fits in place and press it firmly to the back.
f
Tighten the two lamp fixing screws.
g
Replace the lamp cover.
Replacing Consumables
117
Attention
Make sure you install the lamp securely. If the lamp cover is removed, the
power turns off automatically as a safety precaution. If the lamp or the lamp
cover is not installed correctly, the power does not turn on.
This product includes a lamp component that contains mercury (Hg). Please
consult your local regulations regarding disposal or recycling. Do not dispose
of it with normal waste.
Resetting the lamp hours
The projector records how long the lamp is turned on and a message and
indicator notify you when it is time to replace the lamp. After replacing the
lamp, make sure you reset the Lamp Hours from the Configuration menu.
s
"Reset Menu" p.92
a
Only reset the Lamp Hours after the lamp has been replaced.
Otherwise the lamp replacement period is not indicated correctly.
Replacing the Air Filter
Air filter replacement period
If the message is displayed frequently even though the air filter has been
cleaned, replace the air filter.
How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cord.
b
Open the air filter cover.
Slide the air filter cover operation knob, and open the air filter
cover.
c
Remove the air filter.
Grip the tab in the center of the air filter, and pull it straight out.
Replacing Consumables
118
d
Install the new air filter.
Press until it clicks into place.
e
Close the air filter cover.
a
Dispose of used air filters properly in accordance with your local
regulations.
Material of the frame part: Polypropylene
Material of the filter part: Polypropylene
Replacing Consumables
119
There are many glass parts and precision components inside the projector.
To prevent damage due to impacts when transporting, handle the projector
as follows.
Moving Nearby
Check the following points, and move the projector carefully.
Turn off the power to the projector and disconnect all cables.
Attach the cover to the lens.
When Transporting
Preparing packaging
After checking the points in "Moving Nearby", prepare the following and
then pack up the projector.
Set the vertical lens shift to the lowest position.
s "Adjusting the Position of the Projected Image (Lens Shift)" p.22
Fit the protective lens pad that was used at the time of purchase.
Notes when packing and transporting
Enclose the projector securely in buffer material to protect it from shock,
and place it into a strong cardboard container. Be sure to notify the carrier
company that the contents are fragile.
Notes on Transportation
120
Panel Alignment
Adjusts the pixel color shift for the LCD panel. You can adjust the pixels
horizontally and vertically by 0.25 pixels within a range of ±1 pixel.
a
Image quality may decline after performing LCD alignment.
Images for pixels that extend beyond the edge of the projected
screen are not displayed.
a
Press the [Menu] button while projecting.
b
Select Display from Extended.
c
Select Panel Alignment, and then press the [ ] button.
d
Enable Panel Alignment.
(1)
Select Panel Alignment, and then press the [
] button.
(2)
Select On, and then press the [
] button.
(3) Press the [Esc] button to return to the previous screen.
e
Select the color you want to adjust.
(1)
Select Select Color, and then press the [
] button.
(2)
Select R (red) or B (blue), and then press the [
] button.
(3) Press the [Esc] button to return to the previous screen.
f
Select the grid color displayed when making adjustments from
Pattern Color.
(1)
Select Pattern Color, and then press the [
] button.
Image Maintenance
121
(2) Select a combination of R (red), G (green), and B (blue) for the grid color.
R/G/B: Displays a combination all three colors; red, green and blue. The
actual color of the grid is white.
R/G: This is available when R is selected from Select Color. Displays a
combination of two colors; red and green. The actual color of the grid is
yellow.
G/B: This is available when B is selected from Select Color. Displays a
combination of two colors; green and blue. The actual color of the grid is
cyan.
(3) Press the [Esc] button to return to the previous screen.
g
Select Start Adjustments, and then press the [ ] button. When
the message is displayed, press the [
] button again.
Adjustment starts. All four corners are adjusted in order starting at
the top left.
a
The image may become distorted while adjusting. The image is
restored once adjustments are complete.
h
Use the [ ], [ ], [ ], and [ ] buttons to make adjustments, and
then press the [
] button to move to the next adjustment point.
i
When you have adjusted all four corners, select Exit, and then
press the [
] button.
If you feel you still need to make adjustments after correcting all
four points, select Select intersection and adjust and then continue
making adjustments.
Color Uniformity
Adjusts the color tone for the whole screen.
a
The color tone may not be uniform even after performing color
uniformity.
When using EB-4750W/EB-4650/EB-4550, this function is not
available when Color Mode is set to Dynamic or Sports.
s "Selecting the Projection Quality (Selecting Color Mode)" p.44
a
Press the [Menu] button while projecting.
b
Select Display from Extended.
c
Select Color Uniformity, and then press the [ ] button.
The following screen is displayed.
Image Maintenance
122
Adjustment Level: There are multiple levels from white, through
gray, and up to black (for EB-4955WU/EB-4950WU/EB-4855WU/
EB-4850WU there are five levels, and for EB-4750W/EB-4650/
EB-4550 there are four levels). You can adjust each level individually.
Start Adjustments: Starts making color uniformity adjustments.
Reset: Resets all adjustments and settings for Color Uniformity to
their default values.
a
The image may become distorted while adjusting Color
Uniformity. The image is restored once adjustments are
complete.
d
Select Adjustment Level, and then press the [ ] button.
e
Use the [ ][ ] buttons to set the adjustment level.
f
Press the [Esc] button to return to the previous screen.
g
Select Start Adjustments, and then press the [ ] button.
h
Use the [ ], [ ], [ ], and [ ] buttons to select the area you
want to adjust, and then press the [
] button.
If you select the center, the whole screen is adjusted. Adjust the
outer areas first, and then adjust the whole screen.
i
Use the [ ][ ] buttons to select the color you want to adjust,
and then use the [
][ ] buttons to adjust.
Press the [
] button to weaken the color tone. Press the [ ] button
to strengthen the color tone.
Image Maintenance
123
j
Return to step 4 and adjust each level.
k
When you are done, press the [Menu] button.
Image Maintenance
124
Appendix
Using the Quick Wireless Connection USB Key
Connect the optional Quick Wireless Connection USB Key to the wireless
LAN unit installation section. Check the following points when connecting
a computer to the projector using wireless LAN.
The wireless LAN unit (ELPAP07) is connected to the projector.
The projector is setup to connect to the network using wireless LAN.
s "Wireless LAN menu" p.84
a
Turn on the projector, and then press the [LAN] button on the
remote control.
The following screen is displayed.
b
Check that the SSID and IP address information are displayed, and
then remove the wireless LAN unit.
s "Installing the Wireless LAN Unit" p.34
c
Insert the Quick Wireless Connection USB Key in the wireless LAN
unit installation section.
d
When the message "Network information update complete.
Remove the Quick Wireless Connection USB Key Adapter." is
displayed, remove the Quick Wireless Connection USB Key.
After removing the Quick Wireless Connection USB Key, reattach
the wireless LAN unit.
e
Connect the Quick Wireless Connection USB Key to the computer.
From this point on, see the user's guide supplied with the Quick
Wireless Connection USB Key.
Network Functions
126
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status
of multiple Epson projectors that are connected to a network at a computer
monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
About Message Broadcasting
Message Broadcasting is plugin software for EasyMP Monitor.
Message Broadcasting can be used to send a message (JPEG file) to project
on all Epson projectors or specified projectors connected on the network.
The data can be sent manually, or sent automatically using Timer Settings
of EasyMP Monitor.
Download the Message Broadcasting software from the following website.
http://www.epson.com
Changing Settings Using a Web Browser (Web
Control)
By using the Web browser of a computer connected to the projector on a
network, you can make settings and control the projector. This function
allows you to perform setup and control operations remotely. In addition,
since you can use the computer's keyboard, entering characters required for
the setup is easier.
Use Internet Explorer 8.0 or later as the Web browser. If using a Mac OS
X, use Safari.
a
If you set Standby Mode to Communication On, you can use the
Web browser to make settings and perform control even if the
projector is in standby mode (when the power is off).
s Extended - Standby Mode p.78
Projector setup
In the Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
Items in the Configuration menu that cannot be set by the Web browser
Settings Menu - User Button
Extended Menu - Display - Menu Position, Panel Alignment, Color
Uniformity
Extended Menu - User's Logo
Extended Menu - Operation - High Altitude Mode
Extended Menu - Language
Reset Menu
The settings for items on each menu are the same as the projector's
Configuration menu.
s "Configuration Menu" p.70
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make sure the computer and projector are connected to the network.
Set Connection Mode to Advanced from the Configuration menu.
s Network - Wireless LAN - Connection Mode p.84
Monitoring and Controlling
127
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need
to make settings so that a proxy server is not used for a connection.
a
Start the Web browser on the computer.
b
Enter the IP address of the projector in the address input box of
the Web browser, and press the Enter key on the computer's
keyboard.
The Web Control screen is displayed.
When Web Control Password is set in the Network menu from the
projector's Configuration menu, the password entry screen is
displayed.
c
The user ID and password entry screen is displayed.
Enter "EPSONWEB" as the user ID.
The default password is "admin".
a
Enter the user ID even if the password setting is disabled.
You cannot change the user ID.
You can change the password in the Network menu from the
Configuration menu.
s Network - Basic - Web Control Password p.83
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset
email addresses when a problem or warning occurs with a projector. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Mail - Mail Notification p.88
a
Up to a maximum of three notification destinations (addresses) can
be registered, and notification messages can be sent to all three
destinations at once.
If a projector develops a critical problem and suddenly stops
working, it may not be able to send a message notifying an operator
of the problem.
If you set Standby Mode to Communication On, you can control
the projector even if it is in standby mode (when the power is
off).
s Extended - Standby Mode p.78
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning
occurs in the projector, the following email will be sent.
Mail sender: Address for Address 1
Subject: EPSON Projector
Line 1: The projector name where the problem has occurred
Line 2: The IP address set for the projector where the problem has
occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The main message
contents are listed below.
Clean Air Filter (Air Filter Notice)
Internal error
Fan related error
Sensor error
Monitoring and Controlling
128
Lamp timer failure
Lamp out
Internal temperature error
High-speed cooling in progress
Lamp replacement notification
Low Air Flow (Low Air Flow)
Low Air Flow Error (Filter Airflow Error)
No-signal
No Signal is input to the projector. Check the connection status or check
that the power for the signal source is turned on.
Auto Iris Error
Power Err. (Ballast)
See the following to deal with problems or warnings.
s "Reading the Indicators" p.95
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages
are sent to the specified computer when a problem or warning occurs. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Others - SNMP p.89
a
SNMP should be managed by a network administrator or someone
who is familiar with the network.
To use the SNMP function to monitor the projector, you need to
install the SNMP manager program on your computer.
Up to two destination IP addresses can be saved.
Displaying the Web Remote Screen
The Web Remote function allows you to perform projector remote control
operations with a Web browser.
a
Display the Web Control screen.
b
Click Web Remote.
c
The Web Remote screen is displayed.
Monitoring and Controlling
129
A
[ ] button
Turns the projector on.
B
Change input buttons
s "Switching to the Target Image by Remote Control" p.39
C
[Freeze] button
s "Freezing the Image (Freeze)" p.57
D
[A/V Mute] button
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.56
E
[Page] buttons
s "Remote Control" p.12
F
[Volume] buttons
G
[Source Search] button
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.38
H
[t] button
Turns the projector off.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Command list
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
The main contents are listed below.
Item Command
Power ON/OFF
On PWR ON
Off PWR OFF
Signal selection
Computer Auto SOURCE 1F
RGB SOURCE 11
Component SOURCE 14
BNC Auto SOURCE BF
RGB SOURCE B1
Component SOURCE B4
HDMI SOURCE 30
Video SOURCE 41
S-Video SOURCE 42
LAN SOURCE 53
DisplayPort SOURCE 70
Monitoring and Controlling
130
Item Command
A/V Mute On/Off
On MUTE ON
Off MUTE OFF
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
For more details, contact your local dealer or the nearest address provided
in the Epson Projector Contact List.
s Epson Projector Contact List
Cable layouts
Serial connection
Connector shape: D-Sub 9-pin (male)
Projector input port name: RS-232C
<At the projector> <At the computer>
<At the projector> (PC serial cable) <At the computer>
Signal Name Function
GND
Signal wire ground
TD
Transmit data
RD
Receive data
Communications protocol
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
Monitoring and Controlling
131
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
You need to make network settings before you can use PJLink. See the
following for more information on network settings.
s "Network Menu" p.81
It complies with all commands except for the following commands defined
by PJLink Class1, and agreement was confirmed by the PJLink standard
adaptability verification.
URL:http://pjlink.jbmia.or.jp/english/
Non-compatible commands
Function PJLink Command
Mute settings Image muting set AVMT 11
Audio muting set AVMT 21
Input names defined by PJLink and corresponding projector sources
Source PJLink Command
Computer INPT 11
BNC INPT 13
Video INPT 21
S-Video INPT 22
HDMI INPT 32
DisplayPort INPT 35
Source PJLink Command
LAN INPT 52
Manufacturer name displayed for "Manufacture name information query"
EPSON
Model name displayed for "Product name information query"
EPSON 4955/4950
EPSON 4855/4850
EPSON 4750
EPSON 4550
EPSON 4650
About Crestron RoomView
®
Crestron RoomView
®
is an integrated control system provided by
Crestron
®
. It can be used to monitor and control multiple devices
connected on a network.
The projector supports the control protocol, and can therefore be used in a
system built with Crestron RoomView
®
.
Visit the Crestron
®
Web site for details on Crestron RoomView
®
. (Only
English-language displays are supported.)
http://www.crestron.com
The following provides an overview of Crestron RoomView
®
.
Remote operation using a Web browser
You can operate a projector from your computer just like using a remote
control.
Monitoring and Controlling
132
Monitoring and control with application software
You can use Crestron RoomView
®
Express or Crestron RoomView
®
Server Edition provided by Creston
®
to monitor devices in the system, to
communicate with the help desk, and to send emergency messages. See
the following Web site for details.
http://www.crestron.com/getroomview
This manual describes how to perform operations on your computer using
a Web browser.
a
You can only enter single-byte alphanumeric characters and symbols.
The following functions cannot be used while using Crestron
RoomView
®
.
s "Changing Settings Using a Web Browser (Web Control)"
p.127
Message Broadcasting (EasyMP Monitor plug-in)
If you set Standby Mode to Communication On, you can control
the projector even if it is in standby mode (when the power is
off).
s Extended - Standby Mode p.78
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
Make sure the computer and projector are connected to the network.
Set Crestron RoomView to On from the Network menu.
s Network - Others - Crestron RoomView p.89
a
Start the Web browser on the computer.
b
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The operation window is displayed.
Using the operation window
A
You can perform the following operations when you click the buttons.
Button Function
Power Turns the projector power on or off.
Vol-/Vol+ Adjusts the volume.
Monitoring and Controlling
133
Button Function
A/V Mute Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.56
B
Switch to the image from the selected input source. To display input sources that
are not shown in Source List, click (a) or (b) to scroll up or down. The current
video signal input source is displayed in blue.
You can change the source name if necessary.
C
You can perform the following operations when you click the buttons. To display
buttons that are not shown in Source List, click (c) or (d) to scroll left or right.
Button Function
Freeze Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.57
Contrast Adjusts the difference between light and shade in the
images.
Brightness Adjusts the image brightness.
Color Adjusts the color saturation for the images.
Sharpness Adjusts the image sharpness.
Zoom
Click the [z] button to enlarge the image without
changing the projection size. Click the [x] button to
reduce an image that was enlarged with the [
z
] button.
Click the [
], [ ], [ ], or [ ] buttons to change the
position of an enlarged image.
s "Enlarging Part of the Image (E-Zoom)" p.57
D
The [ ], [ ], [ ], and [ ] buttons perform the same operations as the [ ],
[
], [ ], and [ ] buttons on the remote control. You can perform the
following operations when you click the other buttons.
Button Function
OK
Performs the same operation as the [
] button on the
remote control.
s "Remote Control" p.12
Menu Displays and closes the Configuration menu.
Auto If clicked while projecting analog RGB signals from the
Computer port, you can automatically optimize
Tracking, Sync., and Position.
Search Changes to the next input source that is sending an
image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.38
Esc Performs the same operation as the [Esc] button on the
remote control.
s "Remote Control" p.12
E
You can perform the following operations when you click the tabs.
Tab Function
Contact IT Help Displays the Help Desk window. Used to send messages
to, and receive messages from, the administrator using
Crestron RoomView
®
Express.
Info Displays information on the projector that is currently
connected.
Tools Changes settings in the projector that is currently
connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the
operation window. You can use this window to change settings in the
projector that is currently connected.
Monitoring and Controlling
134
A
Crestron Control
Make settings for Crestron
®
central controllers.
B
Projector
The following items can be set.
Item Function
Projector Name Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (The name can contain up to 15 single-byte
alphanumeric characters.)
Location Enter an installation location name for the projector
that is currently connected on the network. (The name
can contain up to 32 single-byte alphanumeric
characters and symbols.)
Assigned To Enter a user name for the projector. (The name can
contain up to 32 single-byte alphanumeric characters
and symbols.)
Item Function
DHCP Select the Enabled check box to use DHCP. You cannot
enter an IP address if DHCP is enabled.
IP Address Enter the IP address to assign to the currently connected
projector.
Subnet Mask Enter a subnet mask for the currently connected
projector.
Default Gateway Enter the gateway address for the currently connected
projector.
Send Click this button to confirm the changes made to the
Projector.
C
Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item Function
New Password Enter the new password when changing the password to
open the Tools window. (The name can contain up to 26
single-byte alphanumeric characters.)
Confirm Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send Click this button to confirm the changes made to the
Admin Password.
D
User Password
Select the Enabled check box to require a password to open the operation window
on the computer.
The following items can be set.
Monitoring and Controlling
135
Item Function
New Password Enter the new password when changing the password to
open the operation window. (The name can contain up
to 26 single-byte alphanumeric characters.)
Confirm Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send Click this button to confirm the changes made to the
User Password.
Monitoring and Controlling
136
The following optional accessories and consumables are available. Please
purchase these products as and when needed. The following list of optional
accessories and consumables is current as of: April 2013. Details of
accessories are subject to change without notice and availability may vary
depending on the country of purchase.
Optional Accessories
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable supplied with the projector
is too short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male
^3)
Use to connect a component video
g
source.
Remote control cable set ELPKC28
(10 m 2 piece set)
Use this to guarantee operation from the remote control from a distance.
Wireless mouse receiver ELPST16
Use this to use the projector's remote control to control the mouse pointer on
the computer or to page up and down.
Wireless LAN unit ELPAP07
Use when connecting the projector to a computer wirelessly and projecting.
Quick Wireless Connection USB Key ELPAP09
Use when you want to quickly establish one-to-one connection between the
projector and a computer with Windows installed.
Polarizer ELPPL01
Attach to this projector when stacking two projectors and projecting 3D images.
(EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only)
Passive 3D Glasses (standard five piece set) ELPGS02A
Passive 3D Glasses (five piece set for children) ELPGS02B
Passive polarized 3D glasses. Use these when viewing 3D images with the
projectors.
(EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only)
Document Camera ELPDC11
Use when projecting images such as books, OHP documents, or slides.
Ceiling pipe (450 mm)
*
ELPFP13
Ceiling pipe (700 mm)
*
ELPFP14
Use when installing the projector on a high ceiling.
Ceiling mount
*
ELPMB22
Use when installing the projector on a ceiling.
Slim Ceiling Mount
*
ELPMB30
Clearly shows the ceiling mount joints.
* Special expertise is required to suspend the projector from a ceiling. Contact
your local dealer or the nearest address provided in the Epson Projector
Contact List.
s Epson Projector Contact List
Consumables
Lamp unit ELPLP77
Use as a replacement for used lamps.
Air filter ELPAF45
Use as a replacement for used air filters.
Optional Accessories and Consumables
137
Projection Distance (For EB-4955WU/EB-4950WU/
EB-4855WU/EB-4850WU)
A
Projection distance
B
is the distance from the center of the lens to the base of the screen. This
changes depending on the setting for vertical lens shift.
C
Center of lens
Unit: cm
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
50" 102x76 154 - 280 0 - +76
60" 122x91 185 - 337 0 - +91
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
80" 163x122 249 - 450 0 - +122
100" 203x152 312 - 564 0 - +152
120" 244x183 376 - 677 0 - +183
150" 305x229 471 - 848 0 - +229
200" 406x305 630 - 1132 0 - +305
250" 508x381 788 - 1415 0 - +381
Unit: cm
16:9 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
50" 111x62 139 - 254 -3 - +66
60" 133x75 168 - 305 -4 - +79
80" 177x100 226 - 408 -6 - +105
100" 221x125 283 - 511 -7 - +131
120" 266x149 341 - 615 -8 - +153
150" 332x187 427 - 769 -10 - +197
200" 443x249 571 - 1027 -14 - +263
250" 553x311 715 - 1285 -17 - +329
290" 642x361 830 - 1491 -20 - +381
Unit: cm
16:10 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
50" 108x67 135 - 247 0 - +67
Screen Size and Projection Distance
138
16:10 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
60" 130x81 163 - 297 0 - +81
80" 172x108 219 - 397 0 - +108
100" 215x135 275 - 498 0 - +135
120" 258x162 331 - 598 0 - +162
150" 323x202 416 - 748 0 - +202
200" 431x269 556 - 999 0 - +269
250" 538x337 696 - 1250 0 - +337
300" 646x404 836 - 1501 0 - +404
Screen Size and Projection Distance
139
Projection Distance (For EB-4750W)
A
Projection distance
B
is the distance from the center of the lens to the base of the screen. This
changes depending on the setting for vertical lens shift.
C
Center of lens
Unit: cm
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 61x46 90 - 187 -9 - +55
50" 102x76 153 - 314 -16 - +92
60" 122x91 185 - 378 -19 - +110
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
80" 163x122 248 - 506 -25 - +147
100" 203x152 311 - 633 -31 - +184
120" 244x183 374 - 761 -38 - +221
150" 305x229 469 - 952 -47 - +276
200" 406x305 627 - 1271 -63 - +368
250" 508x381 785 - 1590 -79 - +460
Unit: cm
16:9 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 66x37 82 - 169 -11 - +48
50" 111x62 139 - 285 -18 - +80
60" 133x75 168 - 343 -21 - +96
80" 177x100 225 - 459 -28 - +128
100" 221x125 282 - 574 -35 - +160
120" 266x149 340 - 690 -43 - +192
150" 332x187 426 - 864 -53 - +240
200" 443x249 569 - 1153 -71 - +320
250" 553x311 712 - 1443 -89 - +400
Unit: cm
16:10 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 65x40 79 - 165 -8 - +49
Screen Size and Projection Distance
140
16:10 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
50" 108x67 135 - 277 -14 - +81
60" 130x81 163 - 334 -17 - +97
80" 172x108 219 - 446 -22 - +130
100" 215x135 274 - 559 -28 - +162
120" 258x162 330 - 671 -33 - +195
150" 323x202 414 - 840 -42 - +244
200" 431x269 553 - 1122 -56 - +325
250" 538x337 693 - 1404 -69 - +406
300" 646x404 832 - 1685 -83 - +487
Screen Size and Projection Distance
141
Projection Distance (For EB-4650/EB-4550)
A
Projection distance
B
is the distance from the center of the lens to the base of the screen. This
changes depending on the setting for vertical lens shift.
C
Center of lens
Unit: cm
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 61x46 74 - 155 -4 - +50
50" 102x76 127 - 261 -7 - +83
60" 122x91 153 - 315 -8 - +100
4:3 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
80" 163x122 206 - 421 -11 - +133
100" 203x152 258 - 527 -13 - +166
120" 244x183 311 - 633 -16 - +199
150" 305x229 390 - 793 -20 - +249
200" 406x305 521 - 1059 -27 - +332
250" 508x381 652 - 1324 -34 - +415
300" 610x457 784 - 1590 -40 - +498
Unit: cm
16:9 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 66x37 82 - 169 -11 - +48
50" 111x62 139 - 285 -18 - +80
60" 133x75 167 - 343 -21 - +96
80" 177x100 225 - 459 -28 - +128
100" 221x125 282 - 575 -35 - +160
120" 266x149 339 - 691 -43 - +192
150" 332x187 425 - 864 -53 - +240
200" 443x249 568 - 1154 -71 - +320
250" 553x311 711 - 1443 -89 - +400
Screen Size and Projection Distance
142
Unit: cm
16:10 Screen Size
AB
Minimum (Wide) to
Maximum (Tele)
Vertical Lens Shift
Top to Bottom
30" 65x40 79 - 165 -8 - +49
50" 108x67 135 - 277 -14 - +81
60" 130x81 163 - 334 -17 - +97
80" 172x108 218 - 446 -22 - +130
100" 215x135 274 - 559 -28 - +162
120" 258x162 330 - 672 -33 - +195
150" 323x202 413 - 841 -42 - +244
200" 431x269 553 - 1122 -56 - +325
250" 538x337 692 - 1404 -69 - +406
Screen Size and Projection Distance
143
Supported Resolutions
Computer signals (analog RGB)
Signal Refresh Rate (Hz) Resolution (Dots)
VGA 60/72/75/85 640x480
SVGA 56/60/72/75/85 800x600
XGA 60/70/75/85 1024x768
WXGA 60 1280x768
60 1366x768
60/75/85 1280x800
WXGA+ 60/75/85 1440x900
WXGA++ 60 1600x900
SXGA 70/75/85 1152x864
60/75/85 1280x1024
60/75/85 1280x960
SXGA+ 60/75 1400x1050
WSXGA+
*1
60 1680x1050
UXGA 60 1600x1200
WUXGA
*2
60 1920x1200
MAC13" 67 640x480
MAC16" 75 832x624
MAC19" 75 1024x768
59 1024x768
Signal Refresh Rate (Hz) Resolution (Dots)
MAC21" 75 1152x870
*1
Only compatible when Wide is selected as the Resolution from the
Configuration menu. (This is not available for EB-4650/EB-4550.)
*2
EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only. Only compatible
when VESA CVT-RB (Reduced Blanking) signal is input.
Even when signals other than those mentioned above are input, it is likely that the
image can be projected. However, not all functions may be supported.
Component Video
Signal Refresh Rate (Hz) Resolution (Dots)
SDTV (480i) 60 720x480
SDTV (576i) 50 720x576
SDTV (480p) 60 720x480
SDTV (576p) 50 720x576
HDTV (720p) 50/60 1280x720
HDTV (1080i) 50/60 1920x1080
HDTV (1080p)
*
50/60 1920x1080
* EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only
Composite video
Signal Refresh Rate (Hz) Resolution (Dots)
TV (NTSC) 60 720x480
TV (SECAM) 50 720x576
TV (PAL) 50/60 720x576
Supported Monitor Displays
144
Input signal from the HDMI port and DisplayPort (EB-4955WU/
EB-4950WU/EB-4855WU/EB-4850WU/EB-4750W)
Signal Refresh Rate (Hz) Resolution (Dots)
VGA 60 640x480
SVGA 60 800x600
XGA 60 1024x768
WXGA 60 1280x800
60 1280x768
*1
60 1366x768
WXGA+ 60 1440x900
WXGA++ 60 1600x900
WSXGA+ 60 1680x1050
SXGA
60 1280x960
60 1280x1024
SXGA+ 60 1400x1050
UXGA 60 1600x1200
WUXGA
*2
60 1920x1200
SDTV
(480i
*3
/480p)
60 720x480
SDTV
(576i
*3
/576p)
50 720x576
HDTV (720p) 50/60 1280x720
HDTV (1080i) 50/60 1920x1080
HDTV (1080p) 24
*3
/30
*3
/50/60 1920x1080
*1DisplayPort input only
*2 EB-4955WU/EB-4950WU/EB-4855WU/EB-4850WU only. Only compatible
when VESA CVT-RB (Reduced Blanking) signal is input.
*3
HDMI input only
Input signal from the HDMI port and DisplayPort (EB-4650/
EB-4550)
Signal Refresh Rate (Hz) Resolution (Dots)
VGA 60 640x480
SVGA 60 800x600
XGA 60 1024x768
WXGA 60 1280x800
60 1280x768
*1
60 1366x768
WXGA+ 60 1440x900
WXGA++ 60 1600x900
SXGA
60 1280x960
60 1280x1024
SXGA+ 60 1400x1050
UXGA 60 1600x1200
SDTV
(480i
*2
/480p)
60 720x480
SDTV
(576i
*2
/576p)
50 720x576
HDTV (720p) 50/60 1280x720
HDTV (1080i) 50/60 1920x1080
HDTV (1080p) 24
*2
/30
*2
/50/60 1920x1080
*1 DisplayPort input only
*2 HDMI input only
Supported Monitor Displays
145
Projector General Specifications
Product name
EB-4955WU EB-4950WU EB-4855WU EB-4850WU EB-4750W EB-4650 EB-4550
Dimensions
472 (W) x 134 (H) x 320 (D) mm (not including raised section)
LCD panel size
0.76" Wide 0.59" Wide 0.63"
Display method
Polysilicon TFT active matrix
Resolution
2,304,000 pixels
WUXGA (1920 (W) x 1200 (H) dots) x 3
1,024,000 pixels
WXGA (1280 (W)
x 800 (H) dots) x
3
786,432 pixels
XGA (1024 (W) x 768 (H) dots) x 3
Focus adjustment
Manual
Zoom adjustment
Manual (1 - 1.8) Manual (1 - 2.0)
Lens shift
Manual (Vertical direction: Maximum approx. 50%, Horizontal direction:
Maximum approx. 10%)
Manual (Vertical
direction: Maxi‐
mum approx. 70%,
Horizontal direc‐
tion: Maximum ap‐
prox. 38%)
Manual (Vertical direction: Maximum
approx. 58%, Horizontal direction:
Maximum approx. 38%)
Lamp
UHE lamp, 280 W Model No.: ELPLP77 UHE lamp, 260 W Model No.: ELPLP77 UHE lamp, 280 W Model No.: ELPLP77 UHE lamp, 260 W
Model No.:
ELPLP77
Max. audio output
10 W monaural
Speaker
1
Power supply
100-240V AC±10% 50/60Hz 4.1 - 1.8A 100-240V AC±10% 50/60Hz 3.9 - 1.7A 100-240V AC±10% 50/60Hz 4.1 - 1.8A 100-240V AC±10%
50/60Hz 3.9 - 1.7A
Specifications
146
Power
con-
sump-
tion
100 to
120 V
area
Operating: 409 W
Standby power consumption
(Communication On): 4.3 W
Standby power consumption
(Communication Off): 0.38 W
Operating: 387 W
Standby power consumption
(Communication On): 4.3 W
Standby power consumption
(Communication Off): 0.38 W
Operating: 409 W
Standby power consumption
(Communication On): 4.3 W
Standby power consumption
(Communication Off): 0.31 W
Operating: 387 W
Standby power
consumption
(Communication
On): 4.3 W
Standby power
consumption
(Communication
Off): 0.31 W
220 to
240 V
area
Operating: 388 W
Standby power consumption
(Communication On): 4.6 W
Standby power consumption
(Communication Off): 0.47 W
Operating: 368 W
Standby power consumption
(Communication On): 4.6 W
Standby power consumption
(Communication Off): 0.47 W
Operating: 388 W
Standby power consumption
(Communication On): 4.6 W
Standby power consumption
(Communication Off): 0.39 W
Operating: 368 W
Standby power
consumption
(Communication
On): 4.6 W
Standby power
consumption
(Communication
Off): 0.39 W
Operating altitude
Altitude 0 to 3048m
Operating temper-
ature
0 to +45˚C
*
(No condensation)
Storage tempera-
ture
-10 to +60˚C (No condensation)
Mass
Approx. 6.6 kg Approx. 6.5 kg
* The operating temperature is 0 to +45˚C when Power Consumption is set to ECO or Temp Interlock is set, and 0 to +40˚C when it is set to Normal at an altitude of 0 to
1499 m.
The operating temperature is 0 to +40˚C when Power Consumption is set to ECO or Temp Interlock is set, and 0 to +35˚C when it is set to Normal at an altitude of 1500
to 3048 m.
s "Settings Menu" p.77
Product name
EB-4955WU EB-4950WU EB-4855WU EB-4850WU EB-4750W EB-4650 EB-4550
Connec-
tors
Computer Port 1
Mini D-Sub15-pin (female) blue
Audio1 port 1
Stereo mini jack (3.5Ф)
BNC port 1
5BNC (female)
Specifications
147
Audio2 port 1
Stereo mini jack (3.5Ф)
DisplayPort 1
DisplayPort
HDMI port 1
HDMI HDCP supported (Audio is only supported by PCM)
Audio3 port 1
Stereo mini jack (3.5Ф)
S-Video port 1
Mini DIN 4-pin
Video port 1
RCA pin jack
Audio-L/R port 1
RCA pin jack x 2 (L-R)
Audio Out port 1
Stereo mini jack (3.5Ф)
Monitor Out port 1
Mini D-Sub15-pin (female) black
LAN port 1
RJ-45
Service port
*
1
USB connector (Type B)
RS-232C port 1
Mini D-Sub 9-pin (male)
Remote port 1
Stereo mini jack (3.5Ф)
USB port (Only for
Wireless LAN unit)
*
1
USB connector (Type A)
* USB 2.0 is supported. However, USB ports are not guaranteed to operate all devices that support USB.
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Specifications
148
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
Located at: 3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
Tel: 562-981-3840
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue
to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Trade Name: EPSON
Type of Product: LCD Projector
Model: H543C/H544C/H545C/H546C/H563C/
H545M/H546M
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established
by the FCC for this equipment. It is the responsibility of the user to obtain
and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
Specifications
149
A
Center of lens
B
Distance from center of lens to suspension bracket fixing point
Units: mm
Appearance
150
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
Ad hoc mode
A method of wireless LAN connection that communicates with wireless LAN clients without using an access point.
AMX Device Discovery
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
Component Video
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
Composite video
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to
make them appear softer. Adjusting this particular property of an image is called contrast adjustment.
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP address
g
to equipment connected to a network.
DICOM
An acronym for Digital Imaging and Communications in Medicine. An international standard that defines image standards and a communications
protocol for medical images.
Gateway Address
This is a server (router) for communicating across a network (subnet) divided according to subnet mask
g
.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting
digital signals sent over DVI and HDMI ports. Because the HDMI port and DisplayPort on this projector supports HDCP, it can project digital images
protected by HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP
encryption.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
Vertical resolution of 720p or 1080i or greater (p =
Progressive
g
, i = Interlace
g
)
Screen
aspect ratio
g
of 16:9
Infrastructure mode
A method for wireless LAN connection in which devices communicate through access points.
Interlace
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
IP Address
A number to identify a computer connected to a network.
Glossary
151
Progressive
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount
of flicker in images decreases because the volume of information has doubled compared with an interlace system.
Refresh Rate
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be
scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh rate and is
expressed in hertz (Hz).
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV
g
High-
Definition Television.
SNMP
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
computers connected to a TCP/IP network.
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source
to sRGB.
Subnet Mask
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
Sync.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is not carried
out correctly, wide vertical stripes appear in the signal.
Trap IP Address
This is the IP address
g
for the destination computer used for error notification in SNMP.
Glossary
152
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as
transportation devices related to aviation, rail, marine, automotive etc.; disaster
prevention devices; various safety devices etc; or functional/precision devices etc, you
should use this product only after giving consideration to including fail-safes and
redundancies into your design to maintain safety and total system reliability. Because
this product was not intended for use in applications requiring extremely high
reliability/safety such as aerospace equipment, main communication equipment,
nuclear power control equipment, or medical equipment related to direct medical care
etc, please make your own judgment on this product’s suitability after a full evaluation.
Trademarks and Copyrights
Mac and Mac OS are trademarks of Apple Inc..
Microsoft, Windows, Windows Vista, PowerPoint, and Windows logo are trademarks
or registered trademarks of Microsoft Corporation in the United States and/or other
countries.
HDMI and High-Definition Multimedia Interface are the trademarks or registered
trademarks of HDMI Licensing LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
This product includes RSA BSAFE
software from RSA Security Inc. RSA is a
registered trademark of RSA Security Inc. BSAFE RSA Security Inc. is a registered trade
mark in the United States and other countries.
WPA
and WPA2
are registered trademarks of the Wi-Fi Alliance.
The DisplayPort Certified Logo and DisplayPort Icons are Registered Trademarks of the
Video Electronics Standards Association (VESA).
The word DisplayPort is a Registered Trademark of VESA in various countries around
the world.
Other product names used herein are also for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2013. All rights reserved.
General Notes
153
3
3D Setup ........................................................ 76
A
A/V Mute ................................................ 11, 56
A/V Settings ................................................. 81
Abs. Color Temp. ........................................ 75
Air exhaust vent ............................................. 8
Air filter replacement period ................... 118
AMX Device Discovery .............................. 89
Aspect ...................................................... 45, 76
Audio Out port ............................................ 10
Audio1 port .................................................... 9
Audio2 port .................................................. 10
Audio3 port .................................................. 10
Audio-L/R port ............................................ 10
Auto Iris ........................................................ 75
Auto Setup .................................................... 76
B
Basic menu .................................................... 83
Beep ............................................................... 80
BNC port ....................................................... 10
Bonjour ......................................................... 90
Brightness ..................................................... 74
C
Ceiling ..................................................... 18, 79
Ceiling mount fixing points ....................... 11
Cleaning ...................................................... 112
Cleaning the air filter and air intake vent
........................................................................ 112
Cleaning the projector's surface .............. 112
Color adjustment ......................................... 75
Color Mode ............................................ 44, 74
Color Saturation .......................................... 74
Color Uniformity ....................................... 122
Computer port ............................................. 10
Configuration menu .................................... 71
Consumables .............................................. 137
Contrast ........................................................ 74
Control panel ............................................... 11
Control Panel Lock ...................................... 78
Crestron RoomView ........................... 90, 132
Cross .............................................................. 57
D
Date & Time ................................................. 80
DHCP ............................................................ 88
DICOM SIM ................................................. 44
Direct Power On .......................................... 80
Display ........................................................... 79
Display Background .................................... 79
DisplayPort ................................................... 10
DisplayPort EQ Setting ............................... 77
Distance ...................................................... 138
Document Camera .................................... 137
Dynamic ........................................................ 44
E
EasyMP Monitor ....................................... 127
Esc .................................................................. 12
ESC/VP21 ................................................... 130
Extended menu ............................................ 78
E-Zoom ......................................................... 57
F
Filter indicator ............................................. 95
Focus ring ....................................................... 8
Freeze ............................................................. 57
Front ........................................................ 18, 79
Front adjustable foot ................................... 11
Full Lock ....................................................... 67
G
Geometric Correction ................................. 77
H
H/V-Keystone .............................................. 77
HDMI port ................................................... 10
Help function ............................................... 94
High Altitude Mode .................................... 80
Horizontal lens shift dial .............................. 8
How to replace the air filter ..................... 118
How to replace the lamp ........................... 115
I
Image menu .................................................. 74
Image Processing ......................................... 77
Indicators ................................................ 95, 96
Info menu ..................................................... 91
Input Signal ............................................ 76, 91
Installation requirements ........................... 18
Inv Direction Button ................................... 80
L
Lamp cover ..................................................... 9
Lamp hours ................................................... 91
Index
154
Lamp indicator ............................................. 95
Lamp replacement period ........................ 115
Language ....................................................... 81
Lens shift ....................................................... 22
Lens shift dial lock ......................................... 8
M
Mail menu ..................................................... 88
Mail Notification ................................. 88, 128
Memory ......................................................... 78
Menu ............................................................. 12
Menu Position .............................................. 79
Message Broadcasting ......................... 90, 127
Messages ....................................................... 79
Monitor displays ........................................ 144
Monitor Out port ......................................... 10
Mosquito NR ................................................ 76
Multi-Projection .................................... 44, 81
Multi-screen ........................................... 50, 81
N
Network Configuration .............................. 82
Network information .................................. 82
Network menu ............................................. 81
Noise Reduction ........................................... 76
Notification email address 1/2/3 ............... 89
O
Operating temperature ............................. 147
Operation ...................................................... 80
Optional accessories .................................. 137
Overheating .................................................. 96
Overscan ....................................................... 77
P
Panel Alignment .......................................... 79
Part names and functions ............................. 8
Password protect .......................................... 65
Photo ............................................................. 44
PJLink .......................................................... 132
Port Number ................................................ 88
Position ......................................................... 76
Power Consumption ................................... 78
Power indicator ............................................ 95
Power inlet ...................................................... 9
Power On Protection .................................. 65
Presentation .................................................. 44
Priority Gateway .......................................... 89
Problem solving ........................................... 95
Progressive .................................................... 76
Projection ...................................................... 79
Projector ID .................................................. 25
Projector keyword ....................................... 84
Projector Name ............................................ 83
Projector setup ........................................... 127
Q
Quick Corner ............................................... 77
Quick Wireless Connection USB Key .... 126
R
Reading mail ............................................... 128
Rear .......................................................... 18, 79
Rear feet ........................................................ 11
Rear screen .................................................... 18
Refresh Rate .................................................. 91
Remote control ............................................ 12
Remote control button lock ....................... 68
Remote control ID ....................................... 25
Remote port .................................................. 10
Remote receiver ............................................. 8
Replacing batteries ....................................... 14
Reset All ........................................................ 92
Reset Memory .............................................. 92
Reset menu ................................................... 92
Resetting the lamp operating time
.................................................................. 92, 118
Resolution ............................................... 76, 91
RoomView .................................................. 133
RS-232C port ................................................ 10
S
Schedule ........................................................ 62
Schedule Settings ......................................... 81
Screen settings .............................................. 19
Screen Size .................................................... 54
Screen size ................................................... 138
Security menu .............................................. 85
Settings menu ............................................... 77
Sharpness ...................................................... 75
Signal menu .................................................. 75
Sleep Mode ................................................... 80
SMTP Server ................................................. 88
SNMP .......................................................... 129
SNMP menu ................................................. 89
Soft keyboard ................................................ 83
Source ...................................................... 53, 91
Source Search ......................................... 11, 38
Specifications ............................................. 146
Index
155
Split Screen ................................................... 77
Split Screen Setup ........................................ 53
Sports ............................................................. 44
sRGB .............................................................. 44
Standby Mode .............................................. 81
Startup Screen .............................................. 79
Startup Source Search ................................. 80
Status indicators ............................................. 8
Storage temperature .................................. 147
Supported monitor displays ..................... 144
S-Video port ................................................. 10
Swap Screens ................................................ 54
Sync Info ....................................................... 91
Sync. ............................................................... 76
T
Temp indicator ............................................ 95
Test Pattern ............................................ 21, 78
Theatre .......................................................... 44
Tint ................................................................ 75
Tracking ........................................................ 76
Trap IP Address 1/2 .................................... 89
U
User Button .................................................. 78
User's Logo ................................................... 58
User's Logo Protection ................................ 65
V
Vertical lens shift dial .................................... 8
Video port ..................................................... 10
Video Range ................................................. 76
Video Signal ........................................... 76, 91
Volume .......................................................... 78
Volume buttons ........................................... 11
W
Web browser .............................................. 127
Web Control ............................................... 127
Web Remote ............................................... 129
Wired LAN menu ........................................ 87
Wireless LAN menu .................................... 84
Wireless LAN Power ................................... 84
Z
Zoom ring ....................................................... 8
Index
156
152


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson Epson EB-4850WU at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson Epson EB-4850WU in the language / languages: English as an attachment in your email.

The manual is 15,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson Epson EB-4850WU

Epson Epson EB-4850WU Quick start guide - All languages - 20 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info