215219
24
Zoom out
Zoom in
Previous page
1/100
Next page
22-Projector Care
Appendices
Appendix.fm3/9/04
fLamp replacement period
It is time to change the lamp when the "Replace the lamp" message appears
in the bottom left hand corner of the screen at the commencement of
projection and remains for 30 seconds.
It is also time to change the lamp when the Warning indicator flashes red at
0.5 second intervals.
fReplacing the lamp
(Spare lamp: ELPLP29)
1
Turn off the projector and wait for the
cool-down period to end. (Approx. 20
seconds)
Remove the power cable and wait for the
lamp to cool down. (Approx. 1 hour)
2
Open the lamp cover.
Lift the lamp cover by putting your fingers in
the latches and lifting upwards.
3
Loosen the fixing screws holding the
lamp in place.
4
Remove the old lamp.
5
Install the new lamp.
Press the lamp until it clicks into place, then
tighten the two fixing screws.
6
Replace the lamp cover.
First insert the tabs, and then press down on
the opposite side until it clicks into place.
p
The time when the replacement message appears varies depending on the colour mode which has been used.
If Theatre Black has been used continuously: About 2900 hours
If other modes have been used continuously: About 1900 hours
When this message is displayed, please replace the lamp as quickly as possible.
The lamp may explode if you continue to use it beyond the lamp replacement period.
Some lamps may stop operating before the replacement message is displayed. It is recommended that you have a
replacement lamp ready in case this happens.
Replacement lamps can be purchased at your nearest dealer.
c
Wait until the lamp has cooled down sufficiently before opening the lamp cover. It takes a further one hour after the cool-
down period has finished for the lamp to be cool enough.
When the lamp is broken, replace it with a new lamp, or contact your dealer for further advice. If replacing the lamp
yourself, be careful to avoid pieces of broken glass.
USERS_E.BOOK Page 22 Tuesday, March 9, 2004 12:52 PM
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson emp tw10h lcd projector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson emp tw10h lcd projector in the language / languages: English as an attachment in your email.

The manual is 9,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson emp tw10h lcd projector

Epson emp tw10h lcd projector User Manual - English, German, French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info