215219
18
Zoom out
Zoom in
Previous page
1/100
Next page
16-When You Suspect a Problem
Trouble.fm3/2/04
Troubleshooting
When You Suspect a Problem
First, check the indicators on the projector.
There are two indicators on the projector unit
which notify you of projector conditions.
Power indicator
lit flashing If the indicator is not lit, the power supply is not on.
Warning indicator
lit flashing Not lit under normal operating conditions.
Condition Cause/Remedy s
Orange
Standby state (Not abnormal)
The power cable should only be disconnected when the projector is in this state.
Press the [Power] button to start projection.
Quick
Reference
Guide
Orange
Cool-downg in progress (Not abnormal)
Please wait. The cool-down period lasts about 20 seconds.
The projector will beep twice to indicate that cool-down has completed.
You cannot operate the [Power] button during the cool-down period. Press the power button
again after cool-down has finished.
Green
Projection in progress (Not abnormal)
Green
Warming-up (Not abnormal)
Please wait. Warming up takes about 40 seconds. When warming up is complete, the
indicator changes to steady green.
Condition Cause/Remedy s
Red
High internal temperature (overheating)
The lamp turns off automatically and projection stops. Wait for about 5 minutes without operating
the projector. After about 5 minutes have passed, unplug the power cable and check the following:
Make sure the air filter and ventilation outlet are clear and that the projector is not positioned
against a wall.
If the air filter is dirty, it should be cleaned.
When the power cable is plugged back in, the projector will return to its previous state. Press the
[Power] button on the projector or on the remote control to turn it back on.
P.8
P.20
Red
(0.5 second
interval)
Lamp problem
Disconnect the power cable from the electrical outlet. Remove the lamp and check that it is not
broken. If the lamp is not broken, re-install it. Reconnect the power cable and press the [Power]
button on the projector or the remote control to turn it back on.
If the lamp is broken, please contact your dealer or the nearest address provided in the
"International Warranty Conditions" in the "Safety Instructions/World-Wide Warranty Terms"
guide (You will not be able to use the projector until the lamp is replaced).
Check that the lamp and lamp cover are securely installed. If the lamp or lamp cover are not
securely installed, the lamp will not switch on.
P.22
Red
(1 second
interval)
Internal problem
Stop using the projector, disconnect the power cable from the electrical outlet and contact your
dealer or the nearest address provided in the "International Warranty Conditions" in the "Safety
Instructions/World-Wide Warranty Terms" guide.
Orange
High-speed cooling in progress
(This is not abnormal, but, if the temperature rises too high again, projection will stop
automatically.)
Set up the projector in a place which is well ventilated and ensure the air filter and ventilation
outlet are clear.
Clean the air filter.
P.8
P.20
Power indicator
Warning indicator
USERS_E.BOOK Page 16 Tuesday, March 9, 2004 12:52 PM
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson emp tw10h lcd projector at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson emp tw10h lcd projector in the language / languages: English as an attachment in your email.

The manual is 9,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson emp tw10h lcd projector

Epson emp tw10h lcd projector User Manual - English, German, French - 100 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info