617849
9
Zoom out
Zoom in
Previous page
1/72
Next page
7
Basic Operations
Procedure
1
Turn on the power for all equipment
connected to the projector.
For a video source, press the [Play] button at the
video source to start playback if necessary.
Check that the indicator on the projector has
stopped flashing and lights orange.
2
Press the [Power] button on either the
remote control or the projector's
control panel to turn on the power.
The indicator flashes green, and after a short
period projection starts.
Check that the indicator has stopped flashing
and lights green. (This takes approximately 20
seconds.)
3
If more than one signal source has been connected, use the remote control or
control panel buttons to select the port which the signal source that you
would like to use is connected to, while referring to the following table.
*1 The display disappears after 1 seconds.
*2 The signal set by "Input A" in the "Advanced" environment setting menu will be displayed.
*3 The signal set by "Input B" in the "Advanced" environment setting menu will be displayed.
Turning On the Power and Projecting Images
The buttons on the remote control and the projector's control panel cannot be operated
while the indicator is flashing green. Wait until it lights steadily.
The message "No-Signal." may appear depending on the projector's menu settings.
"Setting" - "No-Signal Msg." (p.30)
Port
Button to press
Display at top-right of
screen *
1
Projector Remote control
InputA
The input signal source
changes each time the
[Source] button is pressed.
If you do not press the
[Source] button again while
the signal name is appearing
in the top-right corner of the
screen, the signal source will
not change to the next source.
[A]
INPUT A (YCbCr
)
*2
INPUT A (YPbPr )
*2
InputB [B]
INPUT B (RGB)
*3
INPUT B (YCbCr)
*3
INPUT B (YPbPr)
*3
S-Video [S-Video] S Video
Video [Video] Video
D-RGB/ A-RGB DVI-I
[D-RGB] D-RGB
[A-RGB] A-RGB
If only one signal source has been connected, the signals from that source will be
projected without needing to press one of the above buttons.
If the "No-Signal." message does not disappear, check the connections again.
If a laptop computer or a computer with an LCD screen has been connected to the
projector, the images may not be projected straight away. After making the connections,
check the computer to make sure it has been set up to output signals.
The following table shows examples of how to toggle output settings. For details, refer to
the section of the documentation provided with your computer under a heading such as
"External output", "Connecting an external monitor" or similar.
Lights green
Remote control
NEC Panasonic Toshiba IBM Sony Fujitsu Macintosh
[Fn]+[F3] [Fn]+[F3] [Fn]+[F5] [Fn]+[F7] [Fn]+[F7] [Fn]+[F10]
After startup, change the
Control Panel adjustments
so that Mirroring is active.
Connecting the Power Cord
Turning On the Power and Projecting Images
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson EMP-TW100 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson EMP-TW100 in the language / languages: English as an attachment in your email.

The manual is 2,29 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info