214749
118
Zoom out
Zoom in
Previous page
1/165
Next page
117
Problem Solving
User’s Guide
Lamp cover is open error/
Lamp timer failure/
Lamp out
Take out the lamp and check if it is broken. Replacing the Lamp p.142
If the lamp is not broken, put it back in and then turn the power on. If the lamp still does not turn
on, replace it with a new lamp.
If this does not solve the problem, stop using the projector and disconnect the power cable from
the electrical outlet. Then contact your dealer or the nearest address provided in the "International
Warranty Conditions" section of the Safety Instructions/World-Wide Warranty Terms booklet.
If the lamp is broken.
Contact your local dealer for further advice.
(Projection cannot be carried out until the lamp is replaced.)
Check that the lamp and the lamp cover are securely installed. If the lamp or lamp cover is not
securely installed, the lamp will not switch on.
Internal temperature error
(overheating)
The lamp will turn off automatically and projection will stop. Wait for about 5 minutes without
operating the projector. After confirming that the projector enters Standby state, check the
following two points. When done the checking, press the [Power] button to turn the power back
on.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned
against a wall. p.16
If the air filters are blocked, clean or replace them. p.140
If the projector continues to overheat even after the above points have been checked, or if the
indicators show a problem when the power is turned back on, stop using the projector, disconnect
the power cable from the electrical outlet, and contact your dealer or the nearest address provided
in the "International Warranty Conditions" section of the Safety Instructions/World-Wide Warranty
Terms booklet.
High-speed cooling in progress (This is not an abnormality, However, if the temperature rises too high again, projection will stop
automatically.)
Check that the air filters and air exhaust vent are clear and that they are not up against a surface
such as a wall. p.16
If the air filter is blocked, clean it. p.140
Lamp replacement notification Replace the lamp with a new one. p.142
If you continue to use the lamp after it has passed the replacement period, the possibility that the
lamp may break will increase. Replace the lamp with a new one as soon as possible.
* The indicator status will vary depending on the projector status at the time.
: lit : flashing : off
Status Cause Remedy or Status
Red
Red
Red
Red
Red
Orange
Orange
118


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson emp 7950nl at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson emp 7950nl in the language / languages: English as an attachment in your email.

The manual is 9,34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info