500225
3
Zoom out
Zoom in
Previous page
1/158
Next page
User’s Guide
Notations Used in This Guide
Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
Please understand and respect these caution symbols in order to avoid injury to persons or property.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
General information indications
Attention
Indicates procedures which may result in damage or injury if sufficient care is not taken.
a
Indicates additional information and points which may be useful to know regarding a topic.
s Indicates a page where detailed information regarding a topic can be found.
g
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary"
section of the "Appendix".
s "Glossary" p.136
[Name] Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Menu Name Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Notations Used in This Guide ........................ 2
Introduction
Projector Features .......................................... 7
List of Functions by Model........................................7
Quick and Easy Set up, Projection, and Storage..........................8
Easy writing on a whiteboard or blackboard using the pattern function........8
Connecting with a USB cable and projecting (USB Display)................8
Detecting projector movements and automatically correcting image distortion
.........................................................8
Useful Functions for Projecting Images................................8
Increasing projection content in wide (WXGA) screen (EB-915W/EB-910W/EB-96W
only) .....................................................8
Connecting to a network and projecting images from the computer's screen
.........................................................8
Easy connection to a computer with Quick Wireless.....................9
Making the most of the remote control.............................9
Enlarge and project your files with the Document Camera .................9
Enhanced security functions ..................................... 9
Part Names and Functions .................................. 10
Front/Top...................................................10
Rear .......................................................11
Base...................................................... 12
Control Panel................................................13
Remote Control...............................................14
Replacing the remote control batteries............................. 16
Remote control operating range.................................17
Preparing the Projector
Installing the Projector ..................................... 19
Installation Methods ...........................................19
Installation methods.........................................19
Screen Size and Approximate Projection Distance.......................20
Connecting Equipment ..................................... 22
Connecting a Computer .........................................22
Connecting Image Sources.......................................23
Connecting USB Devices .........................................25
Connecting External Equipment...................................26
Connecting a LAN Cable (EB-925/EB-915W/EB-905/EB-96W/EB-95 only) . . . . . . . . 27
Installing the Wireless LAN Unit .................................... 28
Basic Usage
Projecting Images ......................................... 30
From Installation to Projection .....................................30
Automatically Detect Input Signals and Change the Projected Image (Source Search)
..........................................................31
Switching to the Target Image by Remote Control.......................32
Projecting with USB Display......................................32
System requirements .........................................32
Connecting for the first time....................................33
Uninstalling...............................................34
Adjusting Projected Images ................................ 36
Correcting Keystone Distortion....................................36
Correcting automatically (Auto V-Keystone).........................36
Correcting manually (manual H/V-Keystone).........................36
Correcting manually (Quick Corner) ...............................37
Adjusting the Image Size........................................39
Adjusting the Image Position.....................................39
Adjusting the Horizontal Tilt......................................39
Correcting the Focus...........................................40
Adjusting the Volume..........................................40
Selecting the Projection Quality (Selecting Color Mode)...................40
Setting Auto Iris..............................................41
Changing the Aspect Ratio of the Projected Image ......................42
Changing methods..........................................42
Changing the aspect mode (EB-915W/EB-910W/EB-96W only).............42
Changing the aspect mode (EB-925/EB-905/EB-900/EB-95 only) . ...........43
Contents
3
Useful Functions
Projection Functions ....................................... 46
Projecting Without a Computer (Slideshow)...........................46
Specifications for files that can be projected using Slideshow..............46
Slideshow examples.........................................46
Slideshow operating methods ...................................46
Projecting the selected image...................................48
Projecting image files in a folder in sequence (Slideshow)................49
Image file display settings and Slideshow operation settings..............50
Hiding the Image and Sound Temporarily (A/V Mute).....................51
Freezing the Image (Freeze)......................................51
Pointer Function (Pointer)........................................52
Enlarging Part of the Image (E-Zoom)................................ 53
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . . . 54
Saving a User's Logo ...........................................55
Saving User Pattern............................................57
Security Functions ......................................... 59
Managing Users (Password Protect).................................59
Kinds of Password Protect ......................................59
Setting Password Protect......................................59
Entering the Password........................................60
Restricting Operation (Control Panel Lock)............................61
Anti-Theft Lock...............................................62
Installing the wire lock........................................62
Monitoring and Controlling ................................ 63
About EasyMP Monitor ..........................................63
Changing Settings Using a Web Browser (Web Control) ....................63
Projector setup.............................................63
Displaying the Web Control screen...............................64
Displaying the Web Remote screen...............................64
Using the Mail Notification Function to Report Problems................... 66
Reading Error Notification Mail..................................66
Management Using SNMP.......................................66
ESC/VP21 Commands...........................................67
Command list ..............................................67
Cable layouts.............................................. 67
About PJLink................................................68
About Crestron RoomView
®
...................................... 69
Operating a projector from your computer..........................69
Configuration Menu
Using the Configuration Menu .............................. 74
List of Functions ........................................... 75
Configuration Menu Table.......................................75
Network menu ............................................. 76
Image Menu.................................................77
Signal Menu................................................. 78
Settings Menu ................................................80
Extended Menu ............................................... 81
Network Menu...............................................83
Notes on operating the Network menu.............................84
Soft keyboard operations......................................84
Basic menu................................................85
Wireless LAN menu..........................................85
Security menu.............................................. 87
Wired LAN menu (EB-925/EB-915W/EB-905/EB-96W/EB-95 only) . . . . . . . . . . . . 88
Mail menu................................................89
Others menu..............................................90
Reset menu...............................................91
Info Menu (Display Only)........................................91
Reset Menu.................................................92
Troubleshooting
Using the Help ............................................. 94
Problem Solving ........................................... 95
Reading the Indicators .......................................... 95
When the Indicators Provide No Help................................98
Contents
4
Problems Relating to Images...................................... 99
No images appear...........................................99
Moving images are not displayed (only the moving image portion turns black)
........................................................100
Projection stops automatically..................................100
"Not supported" is displayed................................... 100
"No Signal" is displayed...................................... 100
Images are fuzzy, out of focus, or distorted......................... 101
Interference or distortion appear in images ......................... 102
The image is truncated (large) or small, or the aspect is not suitable........ 102
Image colors are not right.....................................103
Images appear dark ......................................... 104
Problems when Projection Starts.................................. 104
The projector does not turn on................................. 104
Other Problems ..............................................105
No sound can be heard or the sound is faint........................ 105
No sound can be heard from the microphone ....................... 105
The remote control does not work............................... 106
I want to change the language for messages and menus................ 106
Mail is not received even if an error occurs with the projector . . . . . . . . . . . . . 106
About Event ID ........................................... 108
Maintenance
Cleaning ................................................. 110
Cleaning the Projector's Surface...................................110
Cleaning the Lens............................................ 110
Cleaning the Air Filter ..........................................110
Replacing Consumables ................................... 112
Replacing the Lamp........................................... 112
Lamp replacement period.....................................112
How to replace the lamp......................................113
Resetting the lamp hours..................................... 115
Replacing the Air Filter......................................... 116
Air filter replacement period ................................... 116
How to replace the air filter .................................... 116
Appendix
Optional Accessories and Consumables .................... 118
Optional Accessories .......................................... 118
Consumables ............................................... 118
Screen Size and Projection Distance ........................ 119
Projection Distance (For EB-925/EB-905) . ............................ 119
Projection Distance (For EB-915W)................................. 120
Projection Distance (For EB-910W)................................. 121
Projection Distance (For EB-900).................................. 123
Projection Distance (For EB-96W).................................. 124
Projection Distance (For EB-95) ................................... 125
Supported Monitor Displays ............................... 127
Supported Resolutions......................................... 127
Computer signals (analog RGB)................................. 127
Component Video.......................................... 127
Composite video........................................... 127
Input signal from the HDMI port ................................ 127
Specifications ............................................ 129
Projector General Specifications ...................................129
Appearance .............................................. 134
Glossary ................................................. 136
General Notes ............................................ 138
About Notations............................................. 138
General Notice:.............................................. 138
Index .................................................... 156
Contents
5
Introduction
This chapter explains the projector's features and the part names.
List of Functions by Model
Available functions differ depending on the model being used. See the table below for a list of the functions available for each model.
Function EB-925 EB-915W EB-910W EB-905 EB-900 EB-96W EB-95
USB Display
*1
HDMI Connection
*2
Auto V-Keystone
WXGA Resolutions - -- -
Quick Wireless
Connection
*3
Wired LAN Connection - -
Wireless LAN
Connection
*4
Network Settings
Slideshow
*1 The USB display requires a commercially available USB cable.
*2 The HDMI connection requires a commercially available HDMI cable.
*3 The Quick Wireless Connection requires a Quick Wireless Connection USB Key.
*4
The wireless LAN connection requires a Wireless LAN unit.
Projector Features
7
Easy connection to a computer with Quick Wireless
By simply connecting the optional Quick
Wireless Connection USB Key to a computer,
you can project the computer's screen.
(Windows computers only)
Making the most of the remote control
You can use the remote control to perform operations such as enlarging
part of the image. You can also use the remote control as a pointer during
presentations or as a mouse for the computer.
s "Pointer Function (Pointer)" p.52
s "Enlarging Part of the Image (E-Zoom)" p.53
s "Using the Remote Control to Operate the Mouse Pointer (Wireless
Mouse)" p.54
Enlarge and project your files with the Document Camera
You can project paper documents and objects using the optional Document
Camera. Image focus is automatically adjusted using the auto focus
function. You can also enlarge images using digital zoom.
s "Optional Accessories" p.118
Enhanced security functions
Password Protect to restrict and manage users
By setting a Password you can restrict who can use the projector.
s "Managing Users (Password Protect)" p.59
Control Panel Lock restricts button operation on the control panel
You can use this to prevent people changing projector settings without
permission at events, in schools, and so on.
s "Restricting Operation (Control Panel Lock)" p.61
Equipped with various anti-theft devices
The projector is equipped with the following types of anti-theft security
devices.
Security slot
Security cable installation point
s
"Anti-Theft Lock" p.62
Projector Features
9
All of the features in this guide are explained using illustrations of EB-925
unless otherwise mentioned.
Front/Top
Name Function
A
Air exhaust vent
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands
near the air exhaust vent, and do not place objects
that may become warped or damaged by heat near
the vent.
B
Remote receiver
Receives signals from the remote control.
C
A/V mute slide knob
Slide the knob to open and close the A/V mute slide.
Name Function
D
Foot adjust lever
Press the foot lever to extend and retract the front foot.
s "Adjusting the Image Position" p.39
E
Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.39
F
A/V mute slide
Close when not using the projector to protect the lens. By
closing during projection you can hide the image and the
sound.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.51
G
Focus ring
Adjusts the image focus.
s "Correcting the Focus" p.40
H
Air intake vent
(air filter)
Takes in air to cool the projector internally.
s "Cleaning the Air Filter" p.110
I
Air filter cover open/
close switch
Opens and closes the air filter cover.
Open this cover when installing the optional wireless LAN
unit.
s "Replacing the Air Filter" p.116
J
Wireless LAN indicator
Displays the access status of the optional Wireless LAN
unit.
K
Zoom ring
Adjusts the image size.
s "Adjusting the Image Size" p.39
L
Control panel
Operates the projector.
s "Control Panel" p.13
M
Lamp cover
Open when replacing the projector's lamp.
s "Replacing the Lamp" p.112
N
Indicators
Indicates the projector's status.
s "Reading the Indicators" p.95
Part Names and Functions
10
Rear
Name Function
A
HDMI port
Inputs video signals from HDMI compatible video
equipment and computers. This projector is compatible
with
HDCP
g
.
s "Connecting Equipment" p.22
B
Power inlet
Connects the power cable to the projector.
s "From Installation to Projection" p.30
C
S-Video port
For S-video signals from video sources.
D
Video port
Inputs composite video signals from video sources.
E
Audio-L/R port
Inputs audio from equipment connected to the S-Video
port or the Video port.
F
Audio1 port
Inputs audio from equipment connected to the
Computer1 port.
G
Monitor Out port
Outputs analog RGB signals input from the Computer1
port to an external monitor. You cannot output signals
input from other ports or component video signals.
H
Audio Out port
Outputs audio from the currently projected image or the
Mic port to an external speaker.
I
Audio2 port
Inputs audio from equipment connected to the
Computer2 port.
Name Function
J
RS-232C port
When controlling the projector from a computer, connect
it to the computer with an RS-232C cable. This port is for
control use and should not normally be used.
s "ESC/VP21 Commands" p.67
K
Mic port
Inputs audio from the microphone.
L
Security slot
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s "Anti-Theft Lock" p.62
M
Speaker
Plays back audio.
N
Remote receiver
Receives signals from the remote control.
O
LAN port
(EB-925/EB-915W/
EB-905/EB-96W/EB-95
only)
Connects a LAN cable to connect to a network.
P
USB(TypeA) port
Connects a USB memory device or a digital camera, and
projects images as a Slideshow.
s
"Projecting Without a Computer (Slideshow)"
p.46
Connects the optional Document Camera.
Q
USB(TypeB) port
Connects the projector to a computer via a
commercially available USB cable, and projects the
images on the computer.
s "Projecting with USB Display" p.32
Connects the projector to a computer via the
commercially available USB cable to use the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
R
Computer2 port
Inputs image signals from a computer and component
video signals from other video sources.
S
Computer1 port
Part Names and Functions
11
Base
Name Function
A
Ceiling mount fixing
points (three points)
Attach the optional Ceiling Mount here when suspending
the projector from a ceiling.
s "Installing the Projector" p.19
s "Optional Accessories" p.118
B
Rear feet
When setup on a surface such as a desk, turn to extend and
retract to adjust the horizontal tilt.
s "Adjusting the Horizontal Tilt" p.39
C
Front adjustable foot
When setup on a surface such as a desk, extend the foot to
adjust the position of the image.
s "Adjusting the Image Position" p.39
Name Function
D
Security cable
installation point
Pass a commercially available wire lock through here and
lock it in place.
s "Installing the wire lock" p.62
Part Names and Functions
12
Control Panel
Name Function
A
[t] button
Turns the projector power on or off.
s "From Installation to Projection" p.30
B
[Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.31
C
[Enter] button
When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
If pressed while projecting analog RGB signals from the
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Display
Position.
Name Function
D
[w][v] buttons
Performs vertical keystone correction.
s "Correcting keystone distortion in vertical
directions" p.36
If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.74
s "Using the Help" p.94
E
[a][b] button
[a] Decreases the volume.
[b] Increases the volume.
s
"Adjusting the Volume" p.40
F
[Help] button
Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.94
G
[Esc] button
Stops the current function.
If pressed when the Configuration menu is displayed, it
moves to the previous menu level.
s "Using the Configuration Menu" p.74
H
[<][>] buttons
Performs horizontal keystone correction.
s "Correcting keystone distortion in horizontal
directions" p.37
If pressed when the Configuration menu or the Help
screen is displayed, these buttons select menu items and
setting values.
s "Using the Configuration Menu" p.74
s "Using the Help" p.94
I
[Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.74
Part Names and Functions
13
Remote Control
Name Function
A
[t] button
Turns the projector power on or off.
s "From Installation to Projection" p.30
B
[Computer] button
Each time you press the button, the input changes between
images from the Computer1 port and the Computer2
port.
C
[Video] button
Each time the button is pressed, the image cycles through
the S-Video, Video, and HDMI ports.
D
Numeric buttons
Enter the Password.
s "Setting Password Protect" p.59
Use this button to enter numbers in Network settings
from the Configuration menu.
E
[A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.51
F
[Freeze] button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.51
G
[Auto] button
If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can
automatically optimize Tracking, Sync., and Display
Position.
H
[Aspect] button
Each time the button is pressed, the aspect mode changes.
s "Changing the Aspect Ratio of the Projected Image "
p.42
I
[Page] buttons
[Up] [Down]
Changes pages in files such as PowerPoint files when using
the following projection methods.
When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
When using USB Display
s "Projecting with USB Display" p.32
When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next screen.
Part Names and Functions
14
Name Function
J
[E-Zoom] buttons
[
z
][
x
]
Enlarges or reduces the image without changing the
projection size.
s "Enlarging Part of the Image (E-Zoom)" p.53
K
[Menu] button
Displays and closes the Configuration menu.
s "Using the Configuration Menu" p.74
L
[ ][ ]
[
][ ] buttons
When the Configuration menu or the Help screen is
displayed, pressing these buttons selects menu items
and setting values.
s "Using the Configuration Menu" p.74
When projecting a Slideshow, pressing these buttons
displays the previous/next image, rotates the image, and
so on.
s "Slideshow operating methods" p.46
During Wireless Mouse function, the mouse pointer
moves in the direction of the button that was pushed.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
M
[Enter] button
When the Configuration menu or the Help screen is
displayed, it accepts and enters the current selection and
moves to the next level.
s "Using the Configuration Menu" p.74
Acts as a mouse's left button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
N
[Esc] button
Stops the current function.
If pressed when the Configuration menu is displayed, it
moves to the previous level.
s "Using the Configuration Menu" p.74
Acts as a mouse's right button when using the Wireless
Mouse function.
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
Name Function
O
[Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.40
P
[Pointer] button
Displays the on-screen pointer.
s "Pointer Function (Pointer)" p.52
Q
[Help] button
Displays and closes the Help screen which shows you how
to deal with problems if they occur.
s "Using the Help" p.94
R
[Color Mode] button
Each time the button is pressed, the Color Mode changes.
s "Selecting the Projection Quality (Selecting Color
Mode)" p.40
S
[Num] button
Hold down this button and press the numeric buttons to
enter passwords and numbers.
s "Setting Password Protect" p.59
T
[User] button
Select any frequently used item from the seven available
Configuration menu items, and assign it to this button. By
pressing the [User] button, the assigned menu item
selection/adjustment screen is displayed, allowing you to
make one-touch settings/adjustments.
s "Settings Menu" p.80
Power Consumption is assigned as the default setting.
U
[USB] button
Each time the button is pressed, it cycles through the
following images:
USB Display
Images from the device connected to the USB(TypeA)
port
V
[LAN] button
Changes to the image projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
W
[Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.31
Part Names and Functions
15
Name Function
X
Remote control light-
emitting area
Outputs remote control signals.
Replacing the remote control batteries
If delays in the responsiveness of the remote control occur or if it does not
operate after it has been used for some time, it probably means that the
batteries are becoming flat. When this happens, replace them with new
batteries. Have two AA size manganese or alkaline batteries ready. You
cannot use other batteries except for the AA size manganese or alkaline.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions
a
Remove the battery cover.
While pushing the battery compartment cover catch, lift the cover
up.
b
Replace the old batteries with new batteries.
Part Names and Functions
16
Caution
Check the positions of the (+) and (-) marks inside the battery holder to
ensure the batteries are inserted the correct way.
c
Replace the battery cover.
Press the battery compartment cover until it clicks into place.
Remote control operating range
Part Names and Functions
17
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installation Methods
The projector supports the following four different projection methods.
Install the projector according to the conditions of the installation location.
Project images from in front of
the screen. (Front projection)
Project images from behind a
translucent screen. (Rear projec-
tion)
Suspend the projector from the
ceiling and project images from
in front of a screen. (Front/Ceil-
ing projection)
Suspend the projector from the
ceiling and project images from
behind a translucent screen.
(Rear/Ceiling projection)
Warning
A special method of installation is required when suspending the projector
from a ceiling (ceiling mount). If it is not installed correctly, it could fall
causing an accident and injury.
If you use adhesives on the Ceiling mount fixing points to prevent the screws
from loosening, or if you use things such as lubricants or oils on the
projector, the projector case may crack causing it to fall from its ceiling
mount. This could cause serious injury to anyone under the ceiling mount
and could damage the projector.
When installing or adjusting the ceiling mount, do not use adhesives to
prevent the screws from loosening and do not use oils or lubricants and so
on.
Attention
Do not use the projector on its side. This may cause malfunctions to occur.
Do not cover the projector's air intake vent or air exhaust vent. If either of
the vents are covered, the internal temperature could rise and cause a fire.
a
An optional Ceiling mount is required when suspending the
projector from a ceiling.
s "Optional Accessories" p.118
You can change the setting as follows by pressing down the [A/V
Mute] button on the remote control for about five seconds.
FrontWFront/Ceiling
Set Rear or Rear/Ceiling from the Configuration menu.
s Extended - Projection p.81
Installation methods
Install the projector as follows.
Installing the Projector
19
Install the projector so that it is parallel to the screen.
If the projector is installed at an angle to the screen, keystone distortion
occurs in the projected image.
Place the projector on a level surface.
If the projector is tilted the projected image is also tilted.
a
See the following if you cannot install the projector parallel to the
screen.
s "Correcting Keystone Distortion" p.36
See the following if you cannot install the projector on a level
surface.
s "Adjusting the Horizontal Tilt" p.39
Screen Size and Approximate Projection Distance
Projection size is determined by the distance from the projector to the
screen. See the illustrations on the right to select the best position according
to the screen size. The illustrations show the approximate shortest distance
at maximum zoom. See the following for more information on the
projection distance.
s
"Screen Size and Projection Distance" p.119
a
When you correct keystone distortion, the projected image may be
reduced.
16:10 Screen Size
EB-915W
(110×67cm)
(170×110cm)
(220×130cm)
(320×200cm)
50”
80”
100”
150”
EB-910W
(110×67cm)
(170×110cm)
(220×130cm)
(320×200cm)
5m
50”
80”
100”
150”
Installing the Projector
20
EB-96W
(110×67cm)
(170×110cm)
(220×130cm)
(320×200cm)
50”
80”
100”
150”
4:3 Screen Size
EB-925/EB-905
EB-900
5m
50”
80”
100”
150”
EB-95
Installing the Projector
21
Illustrations in this section are of EB-925/EB-915W/EB-905/EB-96W/EB-95.
The port name, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A
When using the supplied computer cable
Connect the computer's display output port to the projector's Computer1 or Computer2 port.
B
When using a commercially available USB cable
Connect the computer's USB port to the projector's USB(TypeB) port.
C
When using a commercially available HDMI cable
Connect the computer's HDMI port to the projector's HDMI port.
Computer1/2
Audio1/2
USB TypeB
HDMI
a
You can use a commercially available USB cable to connect the projector to a computer to project images from the computer. This function is called USB
Display.
s "Projecting with USB Display" p.32
You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a
commercially available audio cable.
Connecting Equipment
22
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A
When using a commercially available video or S-video cable
Connect the video or S-video output port on the image source to the projector's Video or S-Video port.
B
When using the optional component video cable
s "Optional Accessories" p.118
Connect the component output port on the image source to the projector's Computer1 or Computer2 port.
C
When using a commercially available HDMI cable
Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.
Computer1/2
Video
S-Video
S-VIDEO
Audio(L-R)
Audio1/2
HDMI
Connecting Equipment
23
Attention
If the input source is on when you connect it to the projector, it could cause a malfunction.
If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
a
If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a
commercially available audio cable.
Connecting Equipment
24
Connecting USB Devices
You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB(TypeA) port on the projector.
When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.
s
"Slideshow examples" p.46
If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search]
button on the control panel, to switch to images from the Document Camera.
s
"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.31
Attention
If you use a USB hub, the connection may not operate correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.
Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.
Connecting Equipment
25
Removing USB devices
After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from
the projector.
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker. You can also output microphone audio from the projector's speaker by
connecting a microphone.
A
When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B
When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
C
When outputting microphone audio
Connect the microphone to the projector's Mic port. When using a condenser microphone, set Plug-in Power to On.
s Extended - Plug-in Power p.81
Monitor Out
Audio Out
Mic
Connecting Equipment
26
a
If you set Standby Mode to Communication On, you can perform the following operations even if the projector is in standby mode.
- Outputting images to an external monitor
- Outputting microphone audio from the projector's speaker (only when Standby Microphone is set to On).
s
Extended - Standby Mode p.81
s Extended - Standby Microphone p.81
Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video
signals.
Setting gauges for functions such as Keystone, Configuration Menu, or Help screens are not output to the external monitor.
When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external
output.
Connecting a LAN Cable (EB-925/EB-915W/EB-905/EB-96W/EB-95 only)
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN
cable.
a
To prevent malfunctions, use a category 5 shielded LAN cable.
Connecting Equipment
27
Installing the Wireless LAN Unit
a
Open the air filter cover.
Slide the air filter cover open/close switch, and open the air filter
cover.
b
Remove the stopper for the Wireless LAN unit.
c
Install the Wireless LAN unit.
d
Fix the stopper in place with the screw.
e
Close the air filter cover.
Connecting Equipment
28
Basic Usage
This chapter explains how to project and adjust images.
From Installation to Projection
This section explains the procedure for connecting the projector to a
computer with the computer cable and projecting images.
b
1
2
3
ON
6
5
4
a
Connect the projector to an electrical outlet with the power cable.
b
Connect the projector to the computer with the computer cable.
c
Turn on the projector.
d
Slide open the A/V mute slide.
e
Turn on your computer.
f
Change the computer's screen output.
When using a laptop computer, you need to change the screen
output from the computer.
Hold down the Fn key (function key), and press the b key.
a
The method for changing differs depending on the computer
being used. See the documentation supplied with the computer.
If the image is not projected, you can change the projected image using one
of the following methods.
Press the [Source Search] button on the control panel or the remote
control.
s
"Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.31
Press the button for the target port on the remote control.
s "Switching to the Target Image by Remote Control" p.32
a
After projecting the image, adjust the image if necessary.
s "Correcting Keystone Distortion" p.36
s "Correcting the Focus" p.40
Projecting Images
30
Automatically Detect Input Signals and Change
the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently
receiving an image.
Because only images from ports receiving an image are projected, you can
quickly project the image you want.
Using the remote control Using the control panel
When two or more image sources are connected, press the [Source Search]
button until the target image is projected.
When your video equipment is connected, start playback before beginning
this operation.
a
The following screen is displayed while no image signals are input.
Projecting Images
31
Switching to the Target Image by Remote Control
You can change directly to the target image by pressing the following
buttons on the remote control.
Remote control
A
Each time the button is pressed, it cycles through the following images:
Computer1 port
Computer2 port
B
Each time the button is pressed, it cycles through the following images:
S-Video port
Video port
HDMI port
C
Each time the button is pressed, it cycles through the following images:
USB Display
Images from the device connected to the USB(TypeA) port
D
Changes to the image projected with EasyMP Network Projection. When
projecting using the optional Quick Wireless Connection USB Key, this
button switches to that image.
Projecting with USB Display
You can use the commercially available USB cable to connect the projector
to a computer to project images from the computer.
To start USB Display, set USB Type B to USB Display from the
Configuration menu.
s Extended - USB Type B p.81
System requirements
For Windows
OS
Windows 2000 Service Pack 4
The following 32 bit operating systems:
Windows XP
Windows XP Service Pack 2 or later
Windows Vista
Windows Vista Service Pack 1 or later
Windows 7
The following 64 bit operating systems:
Windows 7
CPU
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Amount of
Memory
256 MB or more
Recommended: 512 MB or more
Hard Disk
Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1600x1200.
Display color in 16-bit color or greater
Projecting Images
32
For Mac OS
OS
Mac OS X 10.5.1 or later
Mac OS X 10.6.x
CPU
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
Amount of
Memory
512 MB or more
Hard Disk
Space
20 MB or more
Display
Resolution of no less than 640x480 and no higher than
1680x1200.
Display color in 16-bit color or greater
Connecting for the first time
The first time you connect the projector and the computer using the USB
cable, the driver needs to be installed. The procedure is different for
Windows and Mac OS.
a
You do not need to install the driver the next time you connect.
When inputting images from multiple sources, change the input
source to USB Display.
For Windows
a
Connect the computer's USB port to the projector's USB(TypeB)
port using a commercially available USB cable.
For Windows 2000
Double-click Computer, EPSON PJ_UD, and then
EMP_UDSE.EXE.
For Windows XP
Driver installation starts automatically.
For Windows Vista/Windows 7
When the dialog box is displayed, click Run EMP_UDSE.exe.
b
When the License Agreement screen is displayed, click Agree.
c
Computer images are projected.
It may take a while before computer images are projected. Until
computer images are projected, leave the equipment as it is and do
not disconnect the USB cable or turn off the power to the projector.
d
Disconnect the USB cable when you are finished.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware.
Projecting Images
33
a
If it is not installed automatically, double-click My Computer
- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
If nothing is projected for some reason, click All Programs -
EPSON Projector - Epson USB Display - Epson USB
Display Vx.xx on your computer.
When using a computer running Windows 2000 under user
authority, a Windows error message is displayed and you may
not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect
again.
For more details, contact your local dealer or the nearest
address provided in the following document.
s Epson Projector Contact List
For Mac OS
a
Connect the computer's USB port to the projector's USB(TypeB)
port using a commercially available USB cable.
The Setup folder of USB Display is displayed in the Finder.
b
Double-click the USB Display Installer icon.
c
Follow the on-screen instructions to install.
d
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed
in the Dock and menu bar.
e
Computer images are projected.
It may take a while before computer images are projected. Until
computer images are projected, leave the equipment as it is and do
not disconnect the USB cable or turn off the power to the projector.
f
When you finish projection, select Disconnect from the USB
Display icon menu on the menu bar or Dock, and then remove
the USB cable.
a
If the USB Display setup folder is not displayed automatically
in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
If nothing is projected for some reason, click the USB
Display icon in the Dock.
If there is no USB Display icon in the Dock, double-click
USB Display from the Applications folder.
If you select Exit from the USB Display icon menu on the
Dock, USB Display does not start automatically when you
connect the USB cable.
Uninstalling
For Windows 2000
a
Click Start, select Settings, and then click Control Panel.
b
Double-click Add/Remove Programs.
c
Click Change or Remove Programs.
d
Select Epson USB Display and click Change/Remove.
For Windows XP
a
Click Start, and then click Control Panel.
b
Double-click Add or Remove Programs.
c
Select Epson USB Display and click Remove.
For Windows Vista/Windows 7
a
Click Start, and then click Control Panel.
b
Click Uninstall a program under Programs.
Projecting Images
34
c
Select Epson USB Display and click Uninstall.
For Mac OS
a
Open the Applications folder, doucle-click USB Display, and then
double-click Tool.
b
Run USB Display UnInstaller.
Projecting Images
35
Correcting Keystone Distortion
You can correct keystone distortion using one of the following methods.
Correcting automatically (Auto V-Keystone)
Automatically corrects vertical keystone distortion.
Correcting manually (manual H/V-Keystone)
Manually correct distortion in the horizontal and vertical directions
independently.
Correcting manually (Quick Corner)
Manually correct the four corners independently.
a
When you correct keystone distortion, the projected image may be
reduced.
Correcting automatically (Auto V-Keystone)
When the projector detects any movement, for example when it is installed,
moved, or tilted, it automatically corrects vertical keystone distortion. This
function is called Auto V-Keystone.
When the projector remains still for about two seconds after it detects
movement, it displays a screen for adjustment and then automatically
corrects the projected image.
The following conditions are necessary to correct the projected image using
Auto V-Keystone.
Correction angle: approx. 30˚ up and down
a
Auto V-Keystone works only when Projection is set to Front from
the Configuration menu.
s Extended - Projection p.81
If you do not want to use Auto V-Keystone, set Auto V-Keystone to
Off.
s Settings - Keystone - H/V-Keystone - Auto V-Keystone
p.80.
Correcting manually (manual H/V-Keystone)
Manually correct distortion in the horizontal and vertical directions
independently. H/V-Keystone correction is ideal for fine-tuning keystone
distortion.
The following conditions are necessary to correct the projected image using
Auto H/V-Keystone.
Correction angle: approx 30˚ right and left/approx. 30˚ up and down
Correcting keystone distortion in vertical directions
Press the [ ][ ] buttons on the control panel.
Adjusting Projected Images
36
Correcting keystone distortion in horizontal directions
Press the [ ][ ] buttons on the control panel.
a
You can set manual H/V-Keystone from the Configuration menu.
s Settings - Keystone - H/V-Keystone p.80
Correcting manually (Quick Corner)
This allows you to manually correct each of the four corners of the
projected image separately.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.74
Using the remote control Using the control panel
b
Select Keystone from Settings.
c
Select Quick Corner, and then press the [Enter] button.
Adjusting Projected Images
37
d
Using the [ ], [ ], [ ], and [ ] buttons on the
remote control, or the [
], [ ], [ ], and [ ] buttons on the
control panel, select the corner to correct, and then press
the [Enter] button.
e
Using the [ ], [ ], [ ], and [ ] buttons on the
remote control, or the [
], [ ], [ ], and [ ] buttons on the
control panel, correct the position of the corner.
When you press the [Enter] button, the screen shown in step 4 is
displayed.
If the message "Cannot adjust any further." is displayed while
adjusting, you cannot adjust the shape any further in the direction
indicated by the gray triangle.
f
Repeat procedures 4 and 5 as needed to adjust any remaining
corners.
Adjusting Projected Images
38
g
When you are done, press the [Esc] button to exit the correction
menu.
Because Keystone was changed to Quick Corner, the corner
selection screen from step 3 is displayed when you press the [
],
[
], [ ], and [ ] buttons on the control panel next time.
Change Keystone to H/V-Keystone if you want to perform
horizontal and vertical correction using the [
], [ ], [ ], and
[
] buttons on the control panel.
s Settings - Keystone - H/V-Keystone p.80
a
If the [Esc] button is held down for about two seconds while
correcting with Quick Corner, the following screen is displayed.
Reset Quick Corner: Resets the result of Quick Corner
corrections.
Switch to H/V-Keystone: Switches the correction method to
H/V-Keystone.
s "Settings Menu" p.80
Adjusting the Image Size
Turn the zoom ring to adjust the size of the projected image.
T
W T
W
Adjusting the Image Position
Press the foot lever to extend and retract the front foot. You can adjust the
position of the image by tilting the projector up to 16 degrees.
a
The larger the angle of tilt, the harder it becomes to focus. Install the
projector so that it only needs to be tilted at a small angle.
Adjusting the Horizontal Tilt
Extend and retract the rear feet to adjust the projector's horizontal tilt.
Adjusting Projected Images
39
A
Extend the rear foot.
B
Retract the rear foot.
Correcting the Focus
You can correct the focus using the focus ring.
Adjusting the Volume
You can adjust the volume using one of the following methods.
Press the [Volume] button on the control panel or the remote control
to adjust the volume.
[
a] Decreases the volume.
[
b] Increases the volume.
Using the remote control Using the control panel
Adjust the volume from the Configuration menu.
s Settings - Volume p.80
Caution
Do not start at high volume.
A sudden excessive volume may cause loss of hearing. Always lower the volume
before powering off, so that you can power on and then gradually increase the
volume.
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality simply by selecting the
setting that best corresponds to your surroundings when projecting. The
brightness of the image varies depending on the mode selected.
Mode Application
Dynamic
Ideal for use in a bright room. This is the brightest
mode, and reproduces shadow tones well.
Adjusting Projected Images
40
Mode Application
Presentation
Ideal for making presentations using color materials
in a bright room.
Theatre
Ideal for watching films in a dark room. Gives
images a natural tone.
Photo
*1
Ideal for projecting still pictures, such as photos, in
a bright room. The images are vivid and brought
into contrast.
Sports
*2
Ideal for watching TV programmes in a bright
room. The images are vivid and brought to life.
sRGB
Ideal for images that conform to the
sRGB
g
color
standard.
Blackboard
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a
natural tint, just like when projecting onto a screen.
Whiteboard
Ideal for making presentations using a whiteboard.
*1
This selection is only available when the input signal is RGB or when the
source is USB Display, USB, or LAN.
*2 This selection is only available when the input signal is component video, or
when the source is Video.
Each time you press the [Color Mode] button, the Color Mode name is
displayed on the screen and the Color Mode changes.
Remote control
a
You can set Color Mode from the Configuration menu.
s Image - Color Mode p.77
Setting Auto Iris
By automatically setting the luminance according to the brightness of the
displayed image, it lets you enjoy deep and rich images.
a
Press the [Menu] button.
s "Using the Configuration Menu" p.74
Using the remote control Using the control panel
b
Select Auto Iris from Image.
Adjusting Projected Images
41
c
Select On.
The setting is stored for each Color Mode.
d
Press the [Menu] button to finish making settings.
a
Auto Iris can only be set when the Color Mode is Dynamic or
Theatre.
Changing the Aspect Ratio of the Projected
Image
You can change the Aspect Ratio
g
of the projected image to suit the type,
the ratio of height and width, and the resolution of the input signals.
Available Aspect Modes vary depending on the image signal currently being
projected.
Changing methods
Each time you press the [Aspect] button, the Aspect Mode name is
displayed on the screen and the aspect ratio changes.
Remote control
a
You can set the aspect ratio from the Configuration menu.
s Signal - Aspect p.78
Changing the aspect mode (EB-915W/EB-910W/EB-96W only)
Projecting images from video equipment or from the HDMI port
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order Normal or Auto, 16:9, Full, Zoom, and
Native.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
A
Normal or Auto
B
16:9
C
Full
D
Zoom
E
Native
Adjusting Projected Images
42
Projecting images from a computer
The following shows projection examples for each aspect mode.
Aspect Mode Input Signal
XGA 1024X768(4:3) WXGA 1280X800(16:10)
Normal
16:9
Full
Zoom
Native
a
If parts of the image are missing, set the Resolution setting to Wide
or Normal from the Configuration menu, according to the size of the
computer panel.
s Signal - Resolution p.78
Changing the aspect mode (EB-925/EB-905/EB-900/EB-95 only)
Projecting images from video equipment
Each time the [Aspect] button on the remote control is pressed, the aspect
mode changes in the order 4:3 and 16:9.
When inputting a 720p/1080i signal and the aspect mode is set to 4:3, a 4:3
zoom is applied (the right and left sides of the image are cut off).
Example: 720p signal input (resolution: 1280x720, aspect ratio: 16:9)
A
4:3
B
16:9
Projecting images from the HDMI port
Each time the Aspect button on the remote control is pressed, the aspect
mode changes in the order Auto, 4:3, and 16:9.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
Adjusting Projected Images
43
Useful Functions
This chapter explains useful tips for giving presentations, and the Security functions.
Projecting Without a Computer (Slideshow)
By connecting a USB storage device such as a USB memory or a USB hard
disk to the projector, you can project the files stored on the device without
using a computer. This function is called Slideshow.
a
You may not be able to use USB storage devices that incorporate
security functions.
You cannot correct keystone distortion while projecting a Slideshow,
even if you press the [
], [ ], [ ], and [ ] buttons on the
control panel.
Specifications for files that can be projected using Slideshow
Type File Type (Ex-
tension)
Notes
Image .jpg The following cannot be projected.
- CMYK color mode formats
- Progressive formats
- Images with a resolution greater than 8192x8192
Due to the characteristics of JPEG files, images may
not be projected clearly if the compression ratio is
too high.
.bmp Cannot project images with a resolution greater
than 1280x800.
.gif Cannot project images with a resolution greater
than 1280x800.
Cannot project animated GIFs.
.png Cannot project images with a resolution greater
than 1280x800.
a
When connecting and using a USB-compatible hard disk, make sure
you connect the AC adaptor supplied with the hard disk.
The projector does not support some file systems, so use media that
has been formatted in Windows.
Format the media in FAT16/32.
Slideshow examples
Projecting images stored on USB storage
s "Projecting the selected image" p.48
s "Projecting image files in a folder in sequence (Slideshow)" p.49
Slideshow operating methods
Although the following steps are explained based on the remote control,
you can perform the same operations from the control panel.
Starting Slideshow
a
Change the source to USB.
s "Switching to the Target Image by Remote Control" p.32
Projection Functions
46
b
Connect the USB storage device or digital camera to the projector.
s "Connecting USB Devices" p.25
Slideshow starts and the file list screen is displayed.
JPEG files are displayed as thumbnails (file contents are displayed
as small images).
Other files or folders are displayed as icons as shown in the
following table.
Icon File Icon File
JPEG files
*
BMP files
GIF files PNG files
* When it cannot be displayed as a thumbnail, it is displayed as an icon.
a
You can also insert a memory card into a USB card reader and then
connect the reader to the projector. However, some commercially
available USB card readers may not be compatible with the
projector.
If the following screen (Select Drive screen) is displayed, press the
[
], [ ], [ ], and [ ] buttons to select the drive
you want to use, and then press the [Enter] button.
To display the Select Drive screen, position the cursor on Select
Drive at the top of the file list screen, and then press the [Enter]
button.
Projecting images
a
Use the [ ], [ ], [ ], and [ ] buttons to select the
file or folder you want to project.
Projection Functions
47
a
If not all of the files and folders are displayed on the current
screen, press the [Down] button on the remote control, or
position the cursor on Next Page at the bottom of the screen
and press the [Enter] button.
To return to the previous screen, press the [Up] button on the
remote control, or position the cursor on Previous Page at the
top of the screen and press the [Enter] button.
b
Press the [Enter] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are
displayed. To return to the previous screen, position the cursor on
Back to Top and press the [Enter] button.
Rotating images
You can rotate the played images in 90˚ increments. The rotating function
is also available during Slideshow.
a
Play images, or run Slideshow.
b
While projecting, press the [ ] or [ ] button.
Stopping Slideshow
To close Slideshow, disconnect the USB device from the USB port on the
projector. For digital cameras, hard disks, and so on, turn off the power to
the device and then remove.
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed.
Slideshow may not operate correctly.
a
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.46
Projection Functions
48
b
Press the [ ], [ ], [ ], and [ ] buttons to select the
image file you want to project.
c
Press the [Enter] button.
The image is displayed.
a
Press the [ ][ ] buttons to move to the next or previous
image file.
d
Press the [Esc] button to return to the file list screen.
Projecting image files in a folder in sequence (Slideshow)
You can project the image files in a folder in sequence, one at a time. This
function is called Slideshow. Use the following procedure to run
Slideshow.
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No.
The default setting is 3 seconds.
s "Image file display settings and Slideshow operation settings"
p.50
a
Start Slideshow.
The file list screen is displayed.
s "Starting Slideshow" p.46
b
Use the [ ][ ][ ][ ] buttons to position the cursor
over the folder for the Slideshow that you want to run and press
the [Enter] button.
c
Select Slideshow at the bottom right of the file list screen, and
then press the [Enter] button.
Slideshow starts, and the image files in the folder are automatically
projected in sequence, one at a time.
When the last file is projected, the file list is displayed again
automatically. If you set Continuous Play to On in the Option
window, projection starts again from the beginning when it reaches
the end.
s "Image file display settings and Slideshow operation settings"
p.50
You can proceed to the next screen, return to the previous screen, or
stop playback while projecting a Slideshow.
Projection Functions
49
a
If Screen Switching Time on the Option screen is set to No, files do
not change automatically when you select Play Slideshow. Press the
[
] button, the [Enter] button, or the [Down] button on the remote
control to continue to the next file.
You can use the following functions when projecting an image file with
Slideshow.
Freeze
s "Freezing the Image (Freeze)" p.51
A/V Mute
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51
E-Zoom
s "Enlarging Part of the Image (E-Zoom)" p.53
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option
screen.
a
Press the [ ][ ][ ][ ] buttons to position the cursor
over the folder where you want to set display conditions and press
the [Esc] button. Select Option from the submenu displayed, then
press the [Enter] button.
b
When the following Option screen is displayed, set each of the
items.
Enable settings by positioning the cursor on the target item and
pressing the [Enter] button.
The following table shows the details for each item.
Display Order
You can select to display the files in Name Order or Date
Order.
Sort Order
You can select to sort the files In Ascending or In
Descending order.
Continuous
Play
You can set whether to repeat the Slideshow.
Screen Switch-
ing Time
You can set the time for a single file to be displayed in
Slideshow. You can set a time between No (0) to 60
Seconds. When you set No, auto play is disabled.
Effect
You can set the screen effects when changing slides.
c
When you have finished making settings, use the [ ],
[
], [ ], and [ ] buttons to position the cursor over OK
and press [Enter].
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel and press the [Enter] button.
Projection Functions
50
Hiding the Image and Sound Temporarily (A/V
Mute)
You can use this when you want to focus the audience's attention on what
you are saying, or if you do not want to show details such as when you are
changing between files during presentations from a computer.
Each time you press the [A/V Mute] button, or open/close the lens cover
A/V Mute turns on or off.
Remote control Projector
a
If you use this function when projecting moving images, the images
and sound continue to be played back by the source, and you cannot
return to the point where A/V Mute was activated.
Microphone audio is still output even when A/V Mute is turned
on.
You can select the screen displayed when the [A/V Mute] button is
pressed from the Configuration menu.
s Extended - Display - A/V Mute p.81
When the A/V mute slide is closed for approximately 30 minutes,
Lens Cover Timer activates and the power is automatically turned
off. If you do not want Lens Cover Timer to activate, set Lens Cover
Timer to Off.
s Extended - Operation - Lens Cover Timer p.81
The lamp is still lit during A/V Mute, so the lamp hours continue to
accumulate.
Freezing the Image (Freeze)
When Freeze is activated on moving images, the frozen image continues to
project on the screen, so you can project a moving image one frame at a
time like a still photo. Also, you can perform operations such as changing
between files during presentations from a computer without projecting any
images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
Projection Functions
51
a
Audio does not stop.
For moving images, the images continue to play back while the
screen is frozen, so it is not possible to resume projection from the
point where the screen was frozen.
If the [Freeze] button is pressed while the Configuration menu or
the Help screen is displayed, the menu or the Help screen that is
displayed is closed.
Freeze still works while E-Zoom is being used.
Pointer Function (Pointer)
This allows you to move a Pointer icon on the projected image, and helps
you draw attention to the area you are talking about.
a
Display the Pointer.
Each time you press the [Pointer] button, the pointer appears or
disappears.
Remote control
b
Move the Pointer icon ( ).
Remote control
When pressed in conjunction with the adjacent [ ], [ ],
[
], and [ ] buttons, the pointer can be moved diagonally.
a
You can select the shape of the pointer icon from the
Configuration menu.
s
Settings - Pointer Shape p.80
Projection Functions
52
Enlarging Part of the Image (E-Zoom)
This is useful when you want to expand images to see them in greater
detail, such as graphs and tables.
a
Start E-Zoom.
Press the [
z] button to display the Cross ( ).
Remote control
b
Move the Cross ( ) to the area of the image that you want to
enlarge.
Remote control
When pressed in conjunction with the adjacent [ ], [ ],
[
], and [ ] buttons, the pointer can be moved diagonally.
c
Enlarge.
Remote control
[z] button: Expands the area each time
it is pressed. You can expand quickly by
holding the button down.
[x] button: Reduces images that have
been enlarged.
[Esc] button: Cancels E-Zoom.
a
The enlargement ratio appears on the screen. The selected
area can be enlarged to between 1 to 4 times in 25
incremental steps.
During enlarged projection, press the [
], [ ],
[
], and [ ] buttons to scroll the image.
Projection Functions
53
Page Up/Down
[Up] button: Moves to the previous page.
[Down] button: Moves to the next page.
a
When pressed in conjunction with the adjacent [ ],
[
], [ ], and [ ] buttons, the pointer can be moved
diagonally.
If the mouse button settings are set to reverse on the computer, the
operation of the remote control buttons will also be reversed.
The Wireless Mouse function cannot be used while the following
functions are being used.
- While the Configuration menu is being displayed
- While a help menu is being displayed
- While the E-Zoom function is being used
- While a user's logo is being captured
- While a pointer function is being used
- While adjusting sound volume
- While USB Display is being operated
- While displaying a Test Pattern
- While Color Mode is being set
- While Color Mode name is being displayed
- While the Source name is being displayed
- While switching input source
- While Message Broadcasting is being displayed
- While patterns are being displayed
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
a
Once a User's Logo has been saved, the logo cannot be returned to the
factory default.
a
Project the image you want to save as the User's Logo, and then
press the [Menu] button.
s "Using the Configuration Menu" p.74
Using the remote control Using the control panel
b
Select User's Logo from Extended.
Projection Functions
55
a
When User's Logo Protect from Password Protect is set to
On, a message is displayed and the User's Logo cannot be
changed. You can make changes after setting User's Logo
Protect to Off.
s "Managing Users (Password Protect)" p.59
If User's Logo is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom are being performed, the function currently
being performed is cancelled.
c
When the message "Choose this image as the User's Logo?" is
displayed, select Yes.
a
When you press the [Enter] button on the remote control or
the control panel, the screen size may change depending on the
signal to match the actual resolution of the image signal.
d
Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control
panel.
Remote control
a
You can save at 400x300 dots in size.
e
When you press the [Enter] button and the message "Select this
image?" is displayed, select Yes.
Projection Functions
56
f
Select the zoom factor from the zoom setting screen.
g
When the message "Save this image as the User's Logo?" is
displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a
When a User's Logo is saved, the previous User's Logo is
erased.
It takes a while to save. Do not operate the projector or any
connected equipment while it is saving, otherwise
malfunctions may occur.
Saving User Pattern
You can save the image that is currently being projected as a User Pattern.
a
When a User Pattern is saved, the previous User Pattern is erased.
a
Project the image you want to use as the User Pattern, and then
press the [Menu] button.
s "Using the Configuration Menu" p.74
Using the remote control Using the control panel
b
Select Pattern from Settings.
c
Select User Pattern.
Projection Functions
57
The projector has the following enhanced security functions.
Password Protect
You can limit who can use the projector.
Control Panel Lock
You can prevent people changing the settings on the projector without
permission.
s "Restricting Operation (Control Panel Lock)" p.61
Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s "Anti-Theft Lock" p.62
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the password
cannot use the projector to project images even if the projector power is on.
Furthermore, the user's logo that is displayed when you turn on the
projector cannot be changed. This acts as an anti-theft device as the
projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
Kinds of Password Protect
The following three kinds of Password Protect settings can be made
according to how the projector is being used.
Power On Protect
When Power On Protect is On, you need to enter a preset password after
the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not
start.
User's Logo Protect
Even if someone tries to change the User's Logo set by the owner of the
projector, it cannot be changed. When User's Logo Protect is set to On,
the following setting changes for the User's Logo are prohibited.
Capturing a User's Logo
Setting Display Background, Startup Screen, or A/V Mute from
Display
s Extended - Display p.81
Network Protect
When Network Protect is set to On, changing the settings for Network is
prohibited.
s
"Network Menu" p.83
Setting Password Protect
Use the following procedure to set Password Protect.
a
During projection, hold down the [Freeze] button for about five
seconds.
The Password Protect setting menu is displayed.
Remote control
Security Functions
59
a
If Password Protect is already activated, you must enter the
password.
If the password is entered correctly, the Password Protect
setting menu is displayed.
s "Entering the Password" p.60
When the password is set, stick the supplied password protect
sticker in a visible position on the projector as a further theft
deterrent.
b
Select the type of Password Protect you want to set, and then
press the [Enter] button.
c
Select On, and then press the [Enter] button.
Press the [Esc] button, the screen displayed in step 2 is displayed
again.
d
Set the password.
(1) Select Password, and then press the [Enter] button.
(2) When the message "Change the password?" is displayed, select Yes and
then press the [Enter] button. The default password is set to "0000".
Change this to your own desired Password. If you select No, the screen
displayed in step 2 is displayed again.
(3) While holding down the [Num] button, enter a four digit number using
the numeric buttons. The number entered is displayed as "* * * *". When
you enter the fourth digit, the confirmation screen is displayed.
Remote control
(4) Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting
you to re-enter the password.
Entering the Password
When the password entry screen is displayed, enter the password using the
numeric buttons on the remote control.
While holding down the [Num] button, enter the password by pressing the
numeric buttons.
Security Functions
60
When you enter the correct password, Password Protect is temporarily
released.
Attention
If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five
minutes, and then the projector switches to standby mode. If this happens,
disconnect the power plug from the electrical outlet and then reinsert it and
turn the projector's power back on. The projector displays the password entry
screen again so that you can enter the correct password.
If you have forgotten the password, make a note of the "Request Code:
xxxxx" number that appears on the screen and contact the nearest address
provided in the Epson Projector Contact List.
s Epson Projector Contact List
If you continue to repeat the above operation and enter the wrong password
thirty times in succession, the following message is displayed and the
projector does not accept any more password entries. "The projector's
operation will be locked. Contact Epson as described in your documentation."
s Epson Projector Contact List
Restricting Operation (Control Panel Lock)
Perform one of the following to lock the operation buttons on the control
panel.
Full Lock
All of the buttons on the control panel are locked. You cannot perform
any operations from the control panel, including turning the power on or
off.
Partial Lock
All of the buttons on the control panel, except for the [
t] button, are
locked.
This is useful at events or shows when you want to deactivate all buttons
during projection or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
a
Press the [Menu] button while projecting.
s "Using the Configuration Menu" p.74
Using the remote control Using the control panel
b
Select Control Panel Lock from Settings.
c
Select either Full Lock or Partial Lock according to your purpose.
Security Functions
61
d
Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you
chose.
a
You can release the control panel lock by one of the following
two methods.
Select Off from Control Panel Lock.
s Settings - Control Panel Lock p.80
Press and hold down the [Enter] button on the control panel
for about seven seconds, a message is displayed and the lock
is released.
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security
devices.
Security slot
The security slot is compatible with the Microsaver Security System
manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
Security cable installation point
A commercially available theft-prevention wire lock can be passed
through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
Security Functions
62
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status
of multiple Epson projectors that are connected to a network at a computer
monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
The following provides brief descriptions of the monitoring and control
functions that can be carried out using EasyMP Monitor.
Registering projectors for monitoring and control
Projectors on the network can be searched for automatically, and you can
then select which projectors you want to register from the projectors that
are detected.
You can register target projectors by entering their IP addresses.
Registered projectors can also be assigned to groups so that they can
be monitored and controlled in groups.
Monitoring the status of registered projectors
You can check the power status (ON/OFF) for projectors and problems or
warnings that require attention by using the icons.
You can select groups of projectors or a single projector and then check
the cumulative lamp operating time or information such as input sources,
problems, and warnings for the projectors.
Controlling registered projectors
Projectors can be selected in groups or as single projectors, and you can
then carry out operations for the selected projectors such as turning the
power on and off and switching their input sources.
You can use Web Control functions to change the settings in the
projector's configuration menu.
If there are certain control actions which are carried out regularly at
particular times or on particular days, you can use Timer Settings to
register timer settings.
Mail Notification settings
You can set e-mail addresses to which notifications are sent if a status
that requires attention, such as a problem, occurs with a registered
projector.
Sending messages to registered projectors
You can use the Message Broadcasting plugin for EasyMP Monitor to
send JPEG files to registered projectors.
Download the Message Broadcasting plugin from the Web site address
provided at the beginning of this chapter.
Changing Settings Using a Web Browser (Web
Control)
By using a Web browser of a computer connected to the projector on a
network, you can make settings and control the projector. This function
allows you to perform setup and control operations remotely. In addition,
since you can use the computer's keyboard, entering characters required for
the setup is easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. If using a
Mac OS, use Safari or Firefox.
a
If you set Standby Mode to Communication On, you can use a Web
browser to make settings and perform control even if the projector is
in standby mode (when the power is off).
s Extended - Standby Mode p.81
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in a Web browser.
Monitoring and Controlling
63
Items in the Configuration menu that cannot be set by a Web browser
Settings menu - Keystone - Quick Corner
Settings Menu - Pointer Shape
Settings Menu - Pattern
Settings Menu - User Button
Extended Menu - User's Logo
Extended Menu - Language
Extended Menu - Operation - High Altitude Mode
Extended Menu - Operation - Lens Cover Timer
Reset Menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s "Configuration Menu" p.73
Items that can only be set with a Web browser
SNMP Community Name
Monitor Password
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make network settings on the computer and projector and put them into
network connection status. Use Advanced when connecting via a Wireless
LAN.
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need
to make settings so that a proxy server is not used for a connection.
a
Start a Web browser on the computer.
b
Enter the IP address of the projector in the address input box of
the Web browser, and press the Enter key on the computer's
keyboard.
The Web Control screen is displayed.
When Web Control Password is set in the Network menu from the
projector's Configuration menu, the password entry screen is
displayed.
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control
operations with a Web browser.
a
Display the Web Control screen.
b
Click Web Remote.
c
The Web Remote screen is displayed.
Monitoring and Controlling
64
Name Function
A
[t] button
Turns the projector power on or off.
s "From Installation to Projection" p.30
B
[Computer] button
Each time the button is pressed, input changes between
images from the Computer1 port and the Computer2
port.
C
[Video] button
Each time the button is pressed, the image cycles through
Video, S-Video, and HDMI ports.
D
[Freeze] button
Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.51
E
[A/V Mute] button
Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.51
Name Function
F
[Page] buttons
[Up] [Down]
Changes pages in files such as PowerPoint files when using
the following projection methods.
When using the Wireless Mouse function
s "Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.54
When using USB Display
s "Projecting with USB Display" p.32
When connecting to a network
When projecting images using Slideshow, pressing these
buttons displays the previous/next screen.
G
[Source Search]
button
Changes to the next input source that is sending an image.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.31
H
[LAN] button
Changes to the image projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to
that image.
s
"Switching to the Target Image by Remote Control"
p.32
I
[USB] button
Each time the button is pressed, it cycles through the
following images:
USB Display
Images from the device connected to the USB(TypeA)
port
s "Switching to the Target Image by Remote Control"
p.32
J
[Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s "Adjusting the Volume" p.40
Monitoring and Controlling
65
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset
email addresses when a problem or warning occurs with a projector. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Mail - Mail Notification p.89
a
Up to a maximum of three notification destinations (addresses) can
be registered, and notification messages can be sent to all three
destinations at once.
If a projector develops a critical problem and suddenly stops
working, it may not be able to send a message notifying an operator
of the problem.
If you set Standby Mode to Communication On, you can control
the projector even if it is in standby mode (when the power is
off).
s Extended - Standby Mode p.81
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning
occurs in the projector, the following email will be sent.
Subject: EPSON Projector
Line 1: The projector name where the problem has occurred
Line 2: The IP address set for the projector where the problem has
occurred.
Line 3 and on: Details of the problem
The details of the problem are listed line by line. The main message
contents are listed below.
Internal error
Fan related error
Sensor error
Lamp timer failure
Lamp out
Internal temperature error
High-speed cooling in progress
Lamp replacement notification
No-signal
No Signal is input to the projector. Check the connection status or check
that the power for the signal source is turned on.
Auto Iris Error
Power Err. (Ballast)
See the following to deal with problems or warnings.
s "Reading the Indicators" p.95
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages
are sent to the specified computer when a problem or warning occurs. This
will enable the operator to be notified of problems with projectors even at
locations away from the projectors.
s Network - Others - SNMP p.90
Monitoring and Controlling
66
a
SNMP should be managed by a network administrator or someone
who is familiar with the network.
To use the SNMP function to monitor the projector, you need to
install the SNMP manager program on your computer.
The managing function using SNMP cannot be used via wireless
LAN in Quick connection mode.
Up to two destination IP addresses can be saved.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Command list
When the power ON command is transmitted to the projector, the power
turns on and it enters warm-up mode. When the projector's power has
turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and
returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is
output and a ":" is returned.
The main contents are listed below.
Item Command
Power ON/OFF On PWR ON
Off PWR OFF
Signal selection Computer1 Auto SOURCE 1F
RGB SOURCE 11
Component SOURCE 14
Computer2 Auto SOURCE 2F
Item Command
RGB SOURCE 21
Component SOURCE 24
HDMI SOURCE 30
Video SOURCE 41
S-Video SOURCE 42
USB Display SOURCE 51
USB SOURCE 52
LAN SOURCE 53
A/V Mute On/Off On MUTE ON
Off MUTE OFF
Add a Carriage Return (CR) code (0Dh) to the end of each command and
transmit.
For more details, contact your local dealer or the nearest address provided
in the Epson Projector Contact List.
s
Epson Projector Contact List
Cable layouts
Serial connection
Connector shape: D-Sub 9-pin (male)
Monitoring and Controlling
67
Projector input port name: RS-232C
<At the projector> <At the computer>
<At the projector> (PC serial cable) <At the computer>
Signal Name Function
GND Signal wire ground
TD Transmit data
RD Receive data
Communications protocol
Default baud rate setting: 9600 bps
Data length: 8 bit
Parity: None
Stop-bit: 1 bit
Flow control: None
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for
controlling network-compatible projector's as part of their efforts to
standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
It complies with all commands except for the following commands defined
by PJLink Class1, and agreement was confirmed by the PJLink standard
adaptability verification.
URL:http://pjlink.jbmia.or.jp/english/
Non-compatible commands
Function PJLink Command
Mute settings Image muting set AVMT 11
Audio muting set AVMT 21
Input names defined by PJLink and corresponding projector sources
Source PJLink Command
Computer1 INPT 11
Computer2 INPT 12
Video INPT 21
S-Video INPT 22
HDMI INPT 32
USB INPT 41
LAN INPT 52
USB Display INPT 53
Monitoring and Controlling
68
Manufacturer name displayed for "Manufacture name information query"
EPSON
Model name displayed for "Product name information query"
EB-925/C2080XN/PowerLite 1835
EB-915W/C2070WN/PowerLite 915W
EB-910W/C2050WN/PowerLite 910W
EB-905/C2060XN/PowerLite 905
EB-900/C2040XN/PowerLite 900
EB-96W/C2030WN/PowerLite 96W
EB-95/C2020XN/PowerLite 95
About Crestron RoomView
®
Crestron RoomView
®
is an integrated control system provided by
Crestron
®
. It can be used to monitor and control multiple devices
connected on a network.
The projector supports the control protocol, and can therefore be used in a
system built with Crestron RoomView
®
.
Visit the Crestron
®
Web site for details on Crestron RoomView
®
. (Only
English-language displays are supported.)
http://www.crestron.com
The following provides an overview of Crestron RoomView
®
.
Remote operation using a Web browser
You can operate a projector from your computer just like using a remote
control.
Monitoring and control with application software
You can use Crestron RoomView
®
Express or Crestron RoomView
®
Server Edition provided by Creston
®
to monitor devices in the system, to
communicate with the help desk, and to send emergency messages. See
the following Web site for details.
http://www.crestron.com/getroomview
This manual describes how to perform operations on your computer using
a Web browser.
a
You can only enter single-byte alphanumeric characters and symbols.
The following functions cannot be used while using Crestron
RoomView
®
.
s "Changing Settings Using a Web Browser (Web Control)"
p.63
Message Broadcasting (EasyMP Monitor plug-in)
Controling is possible if Standby Mode is set to Communication
On, even if the projector is in standby state (when the power is
off).
s Extended - Standby Mode p.81
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced
connection mode.
s "Wireless LAN menu" p.85
Set RoomView to On from the Network menu.
s Network - Others - RoomView p.90
Monitoring and Controlling
69
a
Start a Web browser on the computer.
b
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The operation window is displayed.
Using the operation window
A
You can perform the following operations when you click the buttons.
Button Function
Power Turns the projector power on or off.
Vol-/Vol+ Adjusts the volume.
Button Function
A/V Mute Turns the video and audio on or off.
s "Hiding the Image and Sound Temporarily (A/V
Mute)" p.51
B
Switch to the image from the selected input source. To display input sources that
are not shown in Source List, click (a) or (b) to scroll up or down.
You can change the source name if necessary.
C
You can perform the following operations when you click the buttons. To display
buttons that are not shown in Source List, click (c) or (d) to scroll left or right.
Button Function
Freeze Images are paused or unpaused.
s "Freezing the Image (Freeze)" p.51
Contrast Adjusts the difference between light and shade in the
images.
Brightness Adjusts the image brightness.
Color Adjusts the color saturation for the images.
Sharpness Adjusts the image sharpness.
Zoom
Click the [z] button to enlarge the image without
changing the projection size. Click the [x] button to
reduce an image that was enlarged with the [
z
] button.
Click the [
], [ ], [ ], or [ ] buttons to change the
position of an enlarged image.
s
"Enlarging Part of the Image (E-Zoom)" p.53
D
The [ ], [ ], [ ], or [ ] buttons perform the same operations as the
[
][ ][ ][ ] buttons on the remote control. You can perform
the following operations when you click the other buttons.
Monitoring and Controlling
70
Button Function
OK Performs the same operation as the [Enter] button on
the remote control.
s "Remote Control" p.14
Menu Displays and closes the Configuration menu.
Auto If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically
optimizes the image by adjusting the Tracking, Sync.,
and Position.
Search Switches to the image from the input port where video
signals are being input.
s "Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.31
Esc Performs the same operation as the [Esc] button on the
remote control.
s "Remote Control" p.14
E
You can perform the following operations when you click the tabs.
Tab Function
Contact IT Help Displays the Help Desk window. Used to send messages
to, and receive messages from, the administrator using
Crestron RoomView
®
Express.
Info Displays information on the projector that is currently
connected.
Tools Changes settings in the projector that is currently
connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the
operation window. You can use this window to change settings in the
projector that is currently connected.
A
Crestron Control
Make settings for Crestron
®
central controllers.
B
Projector
The following items can be set.
Item Function
Projector Name Enter a name to differentiate the projector that is
currently connected from other projectors on the
network. (The name can contain up to 15 single-byte
alphanumeric characters.)
Location Enter an installation location name for the projector
that is currently connected on the network. (The name
can contain up to 32 single-byte alphanumeric
characters and symbols.)
Assigned To Enter a user name for the projector. (The name can
contain up to 32 single-byte alphanumeric characters
and symbols.)
Monitoring and Controlling
71
Item Function
DHCP Select the Enabled check box to use DHCP. You cannot
enter an IP address if DHCP is enabled.
IP Address Enter the IP address to assign to the currently connected
projector.
Subnet Mask Enter a subnet mask for the currently connected
projector.
Default Gateway Enter the gateway address for the currently connected
projector.
Send Click this button to confirm the changes made to the
Projector.
C
Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item Function
New Password Enter the new password when changing the password to
open the Tools window. (The name can contain up to 26
single-byte alphanumeric characters.)
Confirm Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send Click this button to confirm the changes made to the
Admin Password.
D
User Password
Select the Enabled check box to require a password to open the operation window
on the computer.
The following items can be set.
Item Function
New Password Enter the new password when changing the password to
open the operation window. (The name can contain up
to 26 single-byte alphanumeric characters.)
Confirm Enter the same password as you entered in New
Password. If the passwords are not the same, an error is
displayed.
Send Click this button to confirm the changes made to the
User Password.
Monitoring and Controlling
72
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you
can perform the same operations from the control panel. Check the guide
under the menu for the available buttons and their operations.
a
Display the Configuration menu screen.
b
Select a top menu item.
c
Select a submenu item.
d
Change settings.
e
Press the [Menu] button to finish making settings.
Using the Configuration Menu
74
Configuration Menu Table
Settable items vary depending on the model being used and the image
signal and source being projected.
Top Menu Name Submenu Name Items or Setting Values
Image menu
s p.77
Color Mode Dynamic, Presentation, Theatre,
Photo, sRGB, Blackboard, and
Whiteboard
Brightness -24 to 24
Contrast -24 to 24
Color Saturation -32 to 32
Tint -32 to 32
Sharpness -5 to 5
Abs. Color Temp. 5000K to 10000K
Color Adjustment R: -16 to 16
G: -16 to 16
B: -16 to 16
Auto Iris On and Off
Signal menu
s p.78
Auto Setup On and Off
Resolution Auto, Wide, and Normal
Tracking -
Sync. -
Position Up, Down, Left, and Right
Progressive Off, Video, and Film/Auto
Noise Reduction Off, NR1, and NR2
HDMI Video Range Auto, Normal, and Expanded
Input Signal Auto, RGB, and Component
Top Menu Name Submenu Name Items or Setting Values
Video Signal Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Aspect Normal, 4:3, 16:9, Full, Zoom,
and Native
Overscan Auto, Off, 4%, and 8%
Settings menu
s p.80
Keystone H/V-Keystone and Quick Corner
Control Panel Lock Full Lock, Partial Lock, and Off
Pointer Shape Pointer 1, 2, and 3
Power Consumption Normal and ECO
Volume 0 - 20
Mic Input Level 0 - 5
Remote Receiver Front/Rear, Front, Rear and Off
User Button Power Consumption, Info,
Progressive,Test Pattern,
Resolution, Mic Input Level, and
Pattern Display
Pattern Pattern Display, Pattern Type,
User Pattern, and Test Pattern
Extended menu
s p.81
Display Messages, Display Background,
Startup Screen, and A/V Mute
User's Logo -
Projection Front, Front/Ceiling, Rear, and
Rear/Ceiling
Operation Direct Power On, Sleep Mode,
Sleep Mode Timer, Lens Cover
Timer, and High Altitude Mode
Standby Mode Communication On and
Communication Off
Standby Microphone On and Off
List of Functions
75
Top Menu Name Submenu Name Items or Setting Values
Plug-in Power On and Off
USB Type B USB Display and Wireless
Mouse
Language 15 or 35 languages
*1
Info menu
s p.91
Lamp Hours -
Source -
Input Signal -
Resolution -
Video Signal -
Refresh Rate -
Sync Info -
Status -
Serial Number -
Event ID -
Reset menu
s p.92
Reset All -
Reset Lamp Hours -
*1 The number of supported languages differs depending on the region where the
projector is used.
Network menu
Top Menu Name Submenu Name Items or Setting Values
Basic menu
s p.85
Projector Name -
PJLink Password -
Web Control Password -
Projector Keyword On and Off
Wireless LAN menu
s p.85
Wireless LAN Power On and Off
Top Menu Name Submenu Name Items or Setting Values
Connection Mode Quick and Advanced
Channel 1ch, 6ch, and 11ch
Wireless LAN Sys. 802.11b/g and 802.11b/g/n
SSID Auto Setting On and Off
SSID -
IP Settings DHCP, IP Address, Subnet Mask,
and Gateway Address
SSID Display On and Off
IP Address Display On and Off
Security menu
s p.87
Security No, WEP, WPA-PSK, and WPA2-
PSK
WEP Encryption 128Bit and 64Bit
Format ASCII and HEX
Key ID 1, 2, 3, 4
Encryption Key 1, En-
cryption Key 2, Encryp-
tion Key 3, and Encryp-
tion Key 4
-
Authentication Type Open and Shared
PSK -
Wired LAN menu
(EB-925/EB-915W/
EB-905/EB-96W/
EB-95 only)
s p.88
IP Settings DHCP, IP Address, Subnet Mask,
and Gateway Address
IP Address Display On and Off
Mail menu
s p.89
Mail Notification On and Off
SMTP Server -
Port Number -
List of Functions
76
Top Menu Name Submenu Name Items or Setting Values
Address 1 Setting, Ad-
dress 2 Setting, and Ad-
dress 3 Setting
-
Others menu
s p.90
SNMP On and Off
Trap IP Address 1 and
Trap IP Address 2
-
Priority Gateway Wired LAN and Wireless LAN
AMX Device Discovery On and Off
RoomView On and Off
Image Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.31
Submenu Function
Color Mode
You can select the quality of the image to suit your surroundings.
s "Selecting the Projection Quality (Selecting Color Mode)"
p.40
Brightness
You can adjust the image brightness.
Contrast
You can adjust the difference between light and dark in the
images.
Color Saturation
You can adjust the color saturation for the images.
Tint
(Adjustment is only possible when NTSC signals are being input
if you use composite video/S-Video signals.)
You can adjust the image tint.
Sharpness
You can adjust the image sharpness.
List of Functions
77
Submenu Function
Abs. Color Temp.
(This item cannot be selected if Color Mode is set to
sRGB
g
.)
You can adjust the overall tint of the image. You can adjust tints
in 10 stages from 5000 K to 10000 K. The image is tinted blue
when a high value is selected and tinted red when a low value is
selected.
Color Adjust-
ment
(This item cannot be selected if Color Mode is set to
sRGB
g
.)
You can adjust the color strength for Red, Green, and Blue
individually.
Auto Iris
(This item can be set only if Color Mode is set to Dynamic or
Theatre.)
Set to On to adjust the iris to obtain the optimum light for images
being projected.
The setting is stored for each Color Mode.
s "Setting Auto Iris" p.41
Reset
You can reset all adjustment values for the Image menu to their
default settings. See the following to return all menu items to
their default settings.
s "Reset Menu" p.92
Signal Menu
Settable items vary depending on the image signal and source currently
being projected. Setting details are saved for each image signal.
You cannot make settings on the Signal menu when the source is USB
Display, USB, or LAN.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.31
Submenu Function
Auto Setup
Set to On to automatically adjust Tracking, Sync., and Position to
the optimum state when the input signal changes.
Resolution
Set to Auto to automatically identify the resolution of the input
signal. If images are not projected correctly when set to Auto, for
example if some of the image is missing, adjust to Wide for wide
screens, or set to Normal for 4:3 or 5:4 screens depending on the
connected computer.
Tracking
You can adjust computer images when vertical stripes appear in
the images.
Sync.
You can adjust computer images when flickering, fuzziness, or
interference appear in the images.
Position
You can adjust the display position up, down, left, and right when
a part of the image is missing so that the whole image is projected.
List of Functions
78
Submenu Function
Progressive
(This setting can only be adjusted when a component video or
RGB video with an interlaced signal (480i/576i/1080i) is input.
This cannot be set when a digital RGB signal is input.)
Interlace
g
(i) signal is converted to Progressive
g
(p). (IP
conversion)
Off: Ideal for images with a large amount of movement.
Video: Ideal for general video images.
Film/Auto: This is ideal for movie films, computer graphics, and
animation.
Noise Reduction
(This cannot be set when a digital RGB signal is input, or when an
interlace signal is being displayed when Progressive is set to
Off.)
Smoothes out rough images. There are two modes. Select your
favorite setting. It is recommended that this is set to Off when
viewing image sources in which noise is very low, such as for
DVDs.
HDMI Video
Range
When the projector's HDMI port is connected to a DVD player,
the projector's video range is set according to the DVD player's
video range setting.
Input Signal
You can select input signal from Computer port.
If set to Auto, the input signal is set automatically according to
the connected equipment.
If colors do not appear correctly when set to Auto, select the
appropriate signal according to the connected equipment.
Video Signal
You can select the input signal from the Video port. If this is set to
Auto, video signals are recognized automatically. If interference
appears in the image or a problem occurs such as no image is
being projected when set to Auto, select the appropriate signal
depending on the connected equipment.
Aspect
You can set the
aspect ratio
g
for projected images.
s "Changing the Aspect Ratio of the Projected Image " p.42
Submenu Function
Overscan
Changes the output image ratio (the range of the projected
image). You can set the cropping range to Off, 4%, or 8%. When
the source is HDMI, Auto is available. When Auto is selected, it
automatically changes to Off or 8% according to the input signal.
Reset
You can reset all adjustment values on the Signal menu to their
default settings, except for Input Signal.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
List of Functions
79
Settings Menu
Submenu Function
Keystone
You can correct keystone distortion.
When H/V-Keystone is selected:
Correcting manually
Adjust V-Keystone and H-Keystone to correct
horizontal and vertical keystone distortion.
Correcting automatically
Set Auto V-Keystone to On.
(This item cannot be selected if Projection is set to
Front/Ceiling, Rear, or Rear/Ceiling.)
s "Correcting automatically (Auto V-Keystone)" p.36
When Quick Corner is selected:
Select and correct the four corners of the projected image.
s "Correcting manually (Quick Corner)" p.37
Control Panel
Lock
You can use this to restrict operation of the projector's control
panel.
s "Restricting Operation (Control Panel Lock)" p.61
Submenu Function
Pointer Shape
You can select the shape of the pointer.
Pointer 1:
Pointer 2:
Pointer 3:
s "Pointer Function (Pointer)" p.52
Power Consump-
tion
You can set the lamp brightness to one of two settings.
Select ECO if the images being projected are too bright, such as
when projecting images in a dark room or onto a small screen.
When ECO is selected, the power consumption and the lamp's
operating life are changed as follows, and fan rotation noise
during projection is reduced.
Electrical consumption: about 20% decrease, lamp life: about 1.2
times longer
Volume
You can adjust the volume. Setting values are saved for each
source.
Mic Input Level
Adjust this if the microphone input level is low and the
microphone audio output from the projector's speaker is difficult
to hear, or if the input level is too high, resulting in a crackling
sound in audio from the microphone. When Mic Input Level is
turned down to 0, no microphone audio is output from the
speaker.
Remote Receiver
You can limit the reception of the operation signal from the
remote control.
When set to Off, you cannot perform any operations from the
remote control. If you want to make operations from the remote
control, hold down the [Menu] button on the remote control or
the control panel for at least 15 seconds to reset the setting to its
default value.
List of Functions
80
Submenu Function
User Button
You can select and assign an item from the Configuration menu
with the remote control's [User] button. Pressing the [User]
button directly displays the assigned menu item selection/
adjustment screen, allowing you to make one-touch changes to
settings/adjustments. You can assign one of the following items
to the [User] button.
Power Consumption, Info, Progressive,Test Pattern,
Resolution, Mic Input Level, and Pattern Display
Pattern
Pattern Display: Display a pattern.
Pattern Type: You can select from Patterns 1 to 4 or User
Pattern. Patterns 1 to 4 display projection lines such as ruled lines
or a grid.
Pattern 1:
Pattern 2:
Pattern 3:
Pattern 4:
User Pattern: Captures a user pattern.
s "Saving User Pattern" p.57
Test Pattern: When the projector is set up, a test pattern is
displayed so that you can adjust the projection status without
connecting equipment. While the test pattern is displayed, zoom,
focus adjustments, and keystone correction can be performed.
To cancel the test pattern, press the [Esc] button on the remote
control or the control panel.
Attention
If a pattern is displayed for a long time, a residual
image may be visible in projected images.
Submenu Function
Reset
You can reset all adjustment values on the Settings menu to their
default settings, except for User Button.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
Extended Menu
List of Functions
81
Submenu Function
Display
You can make settings related to the projector's display.
Messages: When set to Off, the following items will not be
displayed.
Item names when the Source, Color Mode, or Aspect Ratio
is changed, messages when no signal is being input, and
warnings such as High Temp Warning.
Display Background
*1
: You can set the screen background
to Black, Blue, or Logo when no image signal is available.
Startup Screen
*1
: Set to On to display the User's Logo
when projection starts.
A/V Mute
*1
: You can set the screen displayed when the
remote control's [A/V Mute] button is pressed to Black,
Blue, or Logo.
User's Logo
*1
You can change the user's logo that is displayed as a
background during Display Background, A/V Mute, and so
on.
s "Saving a User's Logo" p.55
Projection
Select from one of the following projection methods
depending on how the projector is installed.
Front, Front/Ceiling, Rear, and Rear/Ceiling
You can change the setting as follows by pressing down
the [A/V Mute] button on the remote control for about five
seconds.
Front
W
Front/Ceiling
Rear
W
Rear/Ceiling
s "Installation Methods" p.19
Submenu Function
Operation
Direct Power On: Set to On to turn on the projector
simply by plugging it in.
When the power cable is plugged in, note that the projector
turns on automatically in cases such as a power outage
being restored.
Sleep Mode: When set to On, this automatically stops
projection when no image signal is being input and no
operations are carried out.
Sleep Mode Timer: When Sleep Mode is set to On, you
can set the time before the projector automatically turns off
within a range of 1 to 30 minutes.
Lens Cover Timer: When set to On, this turns off the
power automatically 30 minutes after the A/V mute slide is
closed.
This is set to On by default.
High Altitude Mode: Set to On when using the projector
above an altitude of 1500 m.
Standby Mode
If you set Communication On, you can perform the
following operations even if the projector is in standby
mode.
Monitoring and controlling the projector over the
network.
s "Monitoring and Controlling" p.63
Outputting analog RGB signals from the Computer1 port
to an external monitor.
Outputting audio from the microphone to the projector's
speaker.
(Only when the Standby Microphone is set to On.)
s "Connecting Image Sources" p.23
Standby Micro-
phone
(This item can only be set when Standby Mode is set to
Communication On.)
When set to On, you can output audio from the
microphone from the projector's speaker even if the
projector is in standby mode.
*2
List of Functions
82
Submenu Function
Plug-in Power
When set to On you can use a microphone with Plug-in
Power support.
USB Type B
Set to USB Display when the projector and a computer are
connected by a USB cable and computer images are
projected.
s "Projecting with USB Display" p.32
Set to Wireless Mouse when the mouse pointer is to be
operated by the Remote Control.
s
"Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)" p.54
Language
You can set the language for messages and menus.
Reset
You can reset the adjustment values for Display
*1
and
Operation
*3
from the Extended menu to their default
settings.
See the following to return all menu items to their default
settings.
s "Reset Menu" p.92
*1When User's Logo Protect is set to On in Password Protect, settings related
to user's logo cannot be changed. You can make changes after setting User's
Logo Protect to Off.
s "Managing Users (Password Protect)" p.59
*2
Audio is not output from the microphone when Power On Protect from
Password Protect is set to On.
*3 Except for High Altitude Mode.
Network Menu
When Network Protect is set to On in Password Protect, a message is
displayed and the network settings cannot be changed. Turn Network
Protect Off and then configure the network.
s "Setting Password Protect" p.59
Submenu Function
Net. Info. - Wire-
less LAN
Displays the following network setting status information.
Connection Mode
Antenna Level
Projector Name
SSID
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
Region Code
*
Net. Info. -
Wired LAN
Displays the following network setting status information.
Projector Name
DHCP
IP Address
Subnet Mask
Gateway Address
MAC Address
List of Functions
83
Submenu Function
Network Config-
uration
The following menus are available for setting Network
items.
Basic, Wireless LAN, Security, Wired LAN, Mail, Others,
Reset, and Complete
* Displays available region information for the Wireless LAN unit being used.
For more details, contact your local dealer or the nearest address provided in
the Epson Projector Contact List.
s Epson Projector Contact List
a
By using a Web browser of a computer connected to the projector on
a network, you can set functions and control the projector. This
function is called Web Control. You can easily enter text using a
keyboard to make settings for Web Control such as security settings.
s "Changing Settings Using a Web Browser (Web Control)" p.63
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is
the same as making operations from the Configuration menu.
When done, make sure you go to the Complete menu, and select Yes, No,
or Cancel. When you select Yes or No, you are returned to the
Configuration menu.
Yes: Saves the settings and exits the Network menu.
No: Does not save the settings and exits the Network menu.
Cancel: Continues displaying the Network menu.
Soft keyboard operations
The Network menu contains items that require input of alphanumerics
during setup. In this case, the following software keyboard is displayed. Use
the [
], [ ], [ ], and [ ] buttons on the remote control or
the [
], [ ], [ ], and [ ] buttons on the control panel to move the
cursor to the desired key, and then press the [Enter] button to enter the
alphanumeric character. Enter figures by holding down the [Num] button
on the remote control, and pressing the numeric buttons. After inputting,
press Finish on the keyboard to confirm your input. Press Cancel on the
keyboard to cancel your input.
Each time the CAPS key is selected and the [Enter] button is pressed, it
sets and changes between upper case and lower case letters.
Each time the SYM1/2 key is selected and the [Enter] button is pressed,
it sets and changes the symbol keys for the section enclosed by the
frame.
List of Functions
84
Basic menu
Submenu Function
Projector Name
Displays the projector name used to identify the projector when
connected to a network.
When editing, you can enter up to 16 single-byte alphanumeric
characters.
PJLink Password
Set a password to use when you access the projector using
compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
Web Control
Password
Set a password to use when making settings and controlling the
projector using Web Control. Enter up to eight single-byte
alphanumeric characters. Web Control is a function that allows
you to set up and control the projector by using a Web browser on
a computer connected on a network.
s "Changing Settings Using a Web Browser (Web Control)"
p.63
Submenu Function
Projector Key-
word
When set to On, you have to enter the keyword when you try to
connect the projector to a computer via a network. As a result,
you can prevent presentations from being interrupted by
connections from other computers.
Normally this should be set to On.
s EasyMP Network Projection Operation Guide
Wireless LAN menu
Submenu Function
Wireless LAN
Power
Turn On when connecting the projector to the computer over
wireless LAN.
If you do not want to connect via wireless LAN, turn it Off to
prevent unauthorized access by others.
This is set to On by default.
List of Functions
85
Submenu Function
Connection
Mode
Set the connection mode when using EasyMP Network
Projection to connect the projector and computer.
This is set to Quick by default.
See the following manual for details on connection mode.
s EasyMP Network Projection Operation Guide
Channel
(This can only be set if Connection Mode is set to Quick.)
Select the frequency band used by the wireless LAN from 1ch,
6ch, or 11ch.
This is set to 11ch by default.
Wireless LAN
Sys.
Set the Wireless LAN system to either 802.11b/g or
802.11b/g/n.
The default value is 802.11b/g/n.
SSID Auto Set-
ting
(This can only be set if Connection Mode is set to Quick.)
Set to On to speed up the projector search.
Set to Off when connecting to multiple projectors at the same
time.
This is set to On by default.
SSID
(This can be set only if SSID Auto Setting is set to Off.)
Enter an
SSID
g
. When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Submenu Function
IP Settings
(This can only be set if Connection Mode is set to Advanced.)
You can make network settings.
DHCP: Set to On to make network settings using
DHCP
g
. If this
is set to On, you cannot set any more addresses.
IP Address: You can input the
IP address
g
assigned to the
projector. You can enter a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask: You can input the
subnet mask
g
for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address: You can input the IP address for the gateway
for the projector. You can enter a number from 0 to 255 in each
field of the address. However, the following
gateway addresses
g
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
SSID Display
To prevent the
SSID
g
from being displayed on the LAN Standby
screen, set this to Off.
IP Address Dis-
play
To prevent the
IP address
g
from being displayed on the LAN
Standby screen, set this to Off.
List of Functions
86
Security menu
Submenu Function
Security
Select the security type from the items that are displayed.
When setting up Security, follow the instructions from the
administrator of the network system you are about to access.
WEP Encryption
You can set the encryption for WEP encryption.
128Bit: Uses 128 (104) bit encoding.
64Bit: Uses 64 (40) bit encoding.
Format
You can set the input method for the WEP encryption key to
ASCII or HEX.
Key ID
Selects the WEP encryption ID key.
Submenu Function
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4
You can enter the key used for WEP encryption. Enter the key in
single-byte characters following instructions from the network
administrator for the network in which the projector
participates. The type and number of characters that can be
entered differs depending on the WEP Encryption and Format
settings.
128Bit - ASCII: Single-byte alphanumeric, 13 characters.
64Bit - ASCII: Single-byte alphanumeric, 5 characters.
128Bit - HEX: 0 to 9 and A to F, 26 characters
64Bit - HEX: 0 to 9 and A to F, 10 characters
Authentication
Type
Set the WEP authentication type.
Open: Uses open system authentication.
Shared: Uses shared key authentication.
PSK
(This can only be set when WPA-PSK or WPA2-PSK are
selected from Security.)
You can enter a Pre-Shared Key (encrypted key) in single-byte
alphanumeric characters. Enter at least 8 and up to 32 characters.
Type of security
When the optional wireless LAN unit is installed and being used in
Advanced connection mode, it is strongly recommended that you set
security. Select one of the following security methods.
WEP
Data is encrypted with a code key (WEP key). This mechanism prevents
communication unless the encrypted keys for the access point and the
projector match.
List of Functions
87
WPA
This is an encryption standard that improves security which is a weak
point of WEP. Although there are multiple kinds of WPA encryption
methods, this projector uses TKIP and AES.
WPA also includes user authentication functions. WPA authentication
provides two methods: using an authentication server, or authenticating
between a computer and an access point without using a server. This
projector supports the latter method, without a server.
a
For setting details, follow the directions from the network
administrator of your network.
Wired LAN menu (EB-925/EB-915W/EB-905/EB-96W/EB-95 only)
Submenu Function
IP Settings
You can make settings related to the following addresses.
DHCP
g
: Set to On to configure the network using DHCP. If this
is set to On, you cannot set any more addresses.
IP Address
g
: You can input the IP address assigned to the
projector. You can input a number from 0 to 255 in each field of
the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
Subnet Mask
g
: You can input the subnet mask for the projector.
You can input a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address
g
: You can input the IP address for the gateway
for the projector. You can input a number from 0 to 255 in each
field of the address. However, the following gateway addresses
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a
number from 0 to 255)
List of Functions
88
Submenu Function
IP Address Dis-
play
To prevent the IP address from being displayed on Network Info
in the Network Menu and on the LAN Standby screen, set this to
Off.
Mail menu
When this is set, you receive an email notification if a problem or warning
occurs in the projector.
s
"Using the Mail Notification Function to Report Problems" p.66
Submenu Function
Mail Notification
Set to On to send an email to the preset addresses when a problem
or warning occurs with a projector.
Submenu Function
SMTP Server
You can input the
IP address
g
for the SMTP server for the
projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
Port Number
You can input the port number for the SMTP server. The default
value is 25. You can input numbers between 1 to 65535.
Address 1 Set-
ting/Address 2
Setting/Address
3 Setting
You can input the email address of the destination to send the
notification email to. You can register up to three destinations.
You can enter up to 32 single-byte alphanumeric characters for
the email addresses.
You can select the problems or warnings to be notified about by
email. When the selected problem or warning occurs in the
projector, an email is sent to the specified destination address
notifying that a problem or warning has occurred. You can select
multiple items from the displayed items.
List of Functions
89
Others menu
Submenu Function
SNMP
Set to On to monitor the projector using SNMP.
To monitor the projector, you need to install the SNMP manager
program on your computer. SNMP should be managed by a
network administrator.
The default value is Off.
Trap IP Address
1/Trap IP Ad-
dress 2
You can register up to two IP addresses for the SNMP trap
notification destination. You can enter a number from 0 to 255 in
each field of the address. However, the following IP addresses
cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x
is a number from 0 to 255)
Priority Gateway
(EB-925/
EB-915W/
EB-905/EB-96W/
EB-95 only)
You can set the priority gateway to a Wired LAN or Wireless
LAN.
Submenu Function
AMX Device Dis-
covery
When the projector is connected to a network, set this to On
when you want to enable the projector to be detected by
AMX
Device Discovery
g
. Set this to Off if you are not connected to an
environment controlled by a controller from AMX or AMX
Device Discovery.
RoomView
Set this to On only when monitoring or controlling the projector
over the network using Crestron RoomView
®
. Otherwise, set
this to Off.
s "About Crestron RoomView
®
" p.69
When this is set to On, the following functions are not available.
Web control
Message Broadcasting (EasyMP Monitor Plug-in)
List of Functions
90
Reset menu
Resets all of the network settings.
Submenu Function
Reset network
settings.
To reset all of the Network settings, select Yes.
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status
of the projector. Items that can be displayed vary depending on the source
currently being projected. Depending on the model used, some input
sources are not supported.
s "Automatically Detect Input Signals and Change the Projected Image
(Source Search)" p.31
Submenu Function
Lamp Hours
You can display the cumulative lamp operating time
*
.
When it reaches the lamp warning time, the characters are
displayed in yellow.
Source
You can display the source name for the connected
equipment currently being projected.
Input Signal
You can display the content of Input Signal set in the
Signal menu according to the source.
Resolution
You can display the resolution.
Video Signal
You can display the settings for Video Signal in the Signal
menu.
Refresh Rate
You can display the
refresh rate
g
.
Sync Info
You can display the image signal information.
This information may be needed if service is required.
List of Functions
91
Submenu Function
Status
This is information about errors that have occurred on the
projector.
This information may be needed if service is required.
Serial Number
Displays the projector's serial number.
Event ID
Displays the application error log.
s "About Event ID" p.108
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours
and above is displayed as "10H", "11H", and so on.
Reset Menu
Submenu Function
Reset All
You can reset all items in the Configuration menu to their default
settings.
The following items are not reset to their defaults: Input Signal,
User's Logo, all items for Network menus, Lamp Hours,
Language, Password, and User Button.
Submenu Function
Reset Lamp
Hours
Clears the cumulative lamp hours use time. Reset when you
replace the lamp.
List of Functions
92
Troubleshooting
This chapter explains how to identify problems and what to do if a problem is found.
If a problem occurs with the projector, the Help screen is displayed to assist
you by pressing the Help button. You can solve problems by answering the
questions.
a
Press the [Help] button.
The Help screen is displayed.
Using the remote control Using the control panel
b
Select a menu item.
Using the remote control Using the control panel
c
Confirm the selection.
Using the remote control Using the control panel
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit the Help.
a
See the following if the Help function does not provide a
solution to the problem.
s "Problem Solving" p.95
Using the Help
94
If you are having a problem with the projector, first check the projector's indicators and refer to "Reading the Indicators" below.
See the following if the indicators do not show clearly what the problem might be.
s "When the Indicators Provide No Help" p.98
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
A
Power indicator Indicates the operating status.
Standby condition
When the [t] button is pressed in this condition, projection starts.
Preparing for network monitoring or cool down in progress
All buttons are disabled while the indicator is flashing.
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [t] button is disabled during warm-up.
Projecting
B
Lamp indicator Indicates the projection lamp status.
C
Temp indicator Indicates the internal temperature status.
Problem Solving
95
Refer to the following table to see what the indicators mean and how to remedy problems that they indicate.
If all indicators are off, check that the power cable is connected correctly and that the power is being supplied normally.
Sometimes, when the power cable is unplugged, the
t indicator remains lit for a short period, but this is not a fault.
: Lit : Flashing : Off : Varies according to the projector status
Status Cause Remedy or Status
Internal Error Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
Fan Error
Sensor Error
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s
Epson Projector Contact List
High Temp Error
(overheating)
The lamp turns off automatically and projection stops. Wait for about five minutes. After about five minutes the projector switches to standby
mode, so check the following two points.
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.110, "Replacing the Air Filter" p.116
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.81
Lamp Error
Lamp Failure
Check the following two points.
Take out the lamp and check if it is cracked.
s "Replacing the Lamp" p.112
Clean the air filter.
s "Cleaning the Air Filter" p.110
Problem Solving
96
Status Cause Remedy or Status
If it is not cracked: Reinstall the lamp and turn on the power.
If the error continues: Replace the lamp with a new one and then turn on the power.
If the error continues: Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest
address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If it is cracked: Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until
the lamp is replaced.)
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s "Extended Menu" p.81
Auto Iris Error
Power Err.
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
High Temp Warning (This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
Check that the air filter and air exhaust vent are clear, and that the projector is not positioned against a wall.
If the air filter is clogged, clean or replace it.
s "Cleaning the Air Filter" p.110, "Replacing the Air Filter" p.116
Replace Lamp Replace it with a new lamp.
s "Replacing the Lamp" p.112
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may explode increases. Replace it with a
new lamp as soon as possible.
a
See the following if the projector is not operating properly, even though the indicators are all showing normal.
s "When the Indicators Provide No Help" p.98
If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or
the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
97
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a
solution, refer to the pages given for each problem.
Problems Relating to Images
No images appear
Projection does not start, the projection area is completely black,
or the projection area is completely blue.
s p.99
Moving images are not displayed
Moving images being projected from a computer appear black
and nothing is projected.
s p.100
Projection stops automatically s p.100
The message "Not supported" is displayed s p.100
The message "No Signal" is displayed s p.100
Interference or distortion appear in images s p.102
The image is truncated (large) or small, or the aspect ratio is not
suitable
Only part of the image is displayed, or the height and width
ratios of the image are not correct.
s p.102
Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
s p.103
Images appear dark s p.104
Problems when projection starts
The projector does not turn on s p.104
Other Problems
No sound can be heard or the sound is faint s p.105
No sound can be heard from the microphone s p.105
The remote control does not work s p.106
I want to change the language for messages and menus s p.106
Mail is not received even if an error occurs with the projector s p.106
Problem Solving
98
Problems Relating to Images
No images appear
Check Remedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cable is not connected correctly or power is not being supplied.
Connect the projector's power cable correctly.
s
"From Installation to Projection" p.30
Check that your electrical outlet or power source is functioning correctly.
Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51
Is the A/V mute slide closed? Open the A/V mute slide.
s "Front/Top" p.10
Are the Configuration menu settings correct? Reset all of the settings.
s Reset - Reset All p.92
When using USB Display, set USB Type B to USB Display.
s Extended - USB Type B p.81
Is the image to be projected completely black?
(Only when projecting computer images)
Some input images, such as screen savers, may be completely black.
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.78
Is the USB cable connected correctly?
(Only when projecting USB Display)
Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.
Is Windows Media Center displayed in full screen?
(Only when projecting using USB Display or network connection)
When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.
Reduce the screen size.
Is an application using the Windows DirectX function displayed?
(Only when projecting using USB Display or network connection)
Applications using the Windows DirectX function may not display images correctly.
Problem Solving
99
Moving images are not displayed (only the moving image portion turns black)
Check Remedy
Is the computer's image signal being output to the LCD and the
monitor?
(Only when projecting images from a laptop computer or a
computer with a built-in LCD screen)
Change the image signal from the computer to external output only. Check your computer's documentation, or contact
the computer's manufacturer.
Projection stops automatically
Check Remedy
Is Sleep Mode set to On? Press the [t] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off.
s Extended - Operation - Sleep Mode p.81
"Not supported" is displayed
Check Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.78
Do the image signal resolution and the refresh rate correspond to the
mode?
(Only when projecting computer images)
Refer to the computer's documentation for how to change the image signal resolution and the refresh rate output from
the computer.
s "Supported Monitor Displays" p.127
"No Signal" is displayed
Check Remedy
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
s "From Installation to Projection" p.30
Is the correct port selected? Change the image by pressing the [Source Search] button on the remote control or the control panel.
s "Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.31
Is the power for the computer or video source turned on? Turn the power on for the equipment.
Problem Solving
100
Interference or distortion appear in images
Check Remedy
Is the image signal format setting correct?
(Only when projecting images from a video source)
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal p.78
Are the cables connected correctly? Check that all the cables required for projection are securely connected.
s "Connecting Equipment" p.22
Is an extension cable being used? If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to
check if the cables you are using may be causing the problem.
Is the correct resolution selected?
(Only when projecting computer images)
Set the computer so that the signals being output are compatible with the projector.
s "Supported Monitor Displays" p.127
s Computer's documentation
Are the
Sync.
g
and Tracking
g
settings adjusted correctly?
(Only when projecting computer images)
Press the [Auto] button on the remote control or the [Enter] button on the control panel to perform automatic
adjustment. If the images are not adjusted correctly even after performing automatic adjustment, you can also make
adjustments from the Configuration menu.
s Signal - Tracking, Sync. p.78
Is Transfer layered window selected?
(Only when projecting USB Display)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then clear the
Transfer layered window checkbox.
The image is truncated (large) or small, or the aspect is not suitable
Check Remedy
Is a wide panel computer image being projected?
(Only when projecting computer images)
Change the setting according to the signal for the connected equipment.
s Signal - Resolution p.78
Is the image still being enlarged by E-Zoom? Press the [Esc] button on the remote control to cancel E-Zoom.
s "Enlarging Part of the Image (E-Zoom)" p.53
Is the image position adjusted correctly? (Only when projecting analog RGB signals input from the Computer1 or Computer2 port)
Press the [Auto] button on the remote control or the [Enter] button on the control panel to adjust the position.
You can also adjust the position from the Configuration menu.
s Signal - Position p.78
Problem Solving
102
Images appear dark
Check Remedy
Is the image brightness set correctly? Adjust the Brightness and Power Consumption settings from the Configuration menu.
s Image - Brightness p.77
s
Settings - Power Consumption p.80
Is the
contrast
g
adjusted correctly? Adjust the Contrast setting from the Configuration menu.
s Image - Contrast p.77
Is it time to replace the lamp? When the lamp is nearly ready for replacement, the images become darker and the color quality becomes poorer. When
this happens, replace the lamp with a new lamp.
s "Replacing the Lamp" p.112
Problems when Projection Starts
The projector does not turn on
Check Remedy
Did you press the [t] button? Press the [t] button to turn the power on.
Are the indicators switched off? The power cable is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cable.
s "From Installation to Projection" p.30
Check that your electrical outlet or power source is functioning correctly.
Do the indicators turn on and off when the power cable is touched? There is probably a poor contact in the power cable, or the power cable may be defective. Reinsert the power cable. If this
does not solve the problem, stop using the projector, disconnect the power cable from the electrical outlet, and contact
your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Is the Control Panel Lock set to Full Lock? Press the [t] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off.
s Settings - Control Panel Lock p.80
Is the correct setting for the remote receiver selected? Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver p.80
Problem Solving
104
Other Problems
No sound can be heard or the sound is faint
Check Remedy
Check that the audio/video cable is securely attached to both the
projector and audio source.
Disconnect the cable from the Audio port, and then reconnect the cable.
Is the volume adjusted to the minimum setting? Adjust the volume so that sound can be heard.
s Settings - Volume p.80
s
"Adjusting the Volume" p.40
Is the Mic Input Level set at the maximum? Lower the Mic Input Level.
s Settings - Mic Input Level p.80
Is A/V Mute active? Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s "Hiding the Image and Sound Temporarily (A/V Mute)" p.51
Is the audio cable's specification "No resistance"? When using a commercially available audio cable, make sure it is labeled "No resistance".
Is it connected with an HDMI cable? If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Is Output audio from the projector selected?
(Only when projecting USB Display)
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Output audio from the projector.
No sound can be heard from the microphone
Check Remedy
Is the microphone connected correctly? Disconnect the cable from the Mic port, and then reconnect the cable.
s "Connecting External Equipment" p.26
Is the Mic Input Volume turned down too low? Adjust the Mic Input Volume so that sound can be heard.
s Settings - Mic Input Level p.80
Is Plug-in Power set correctly? When using a condenser microphone, set Plug-in Power to On.
s Extended - Plug-in Power p.81
Problem Solving
105
Check Remedy
Is power being supplied to the projector? Check that your electrical outlet or power source is functioning correctly.
Is the Mail Notification function set correctly in the Configuration
menu?
An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
s "Mail menu" p.89
Problem Solving
107
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local
dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Event ID Cause Remedy
0432
0435
Failed to startup EasyMP Network Projection. Restart the projector.
0434
0482
0484
0485
Network communication is unstable. Check the network communication status, and reconnect after waiting for a
while.
0433 Cannot play transferred images. Restart EasyMP Network Projection.
0481 Communication was disconnected from the computer.
0483
04FE
EasyMP Network Projection ended unexpectedly. Check the network communication status, and then restart the projector.
0479
04FF
A system error occurred in the projector. Restart the projector.
0891 Cannot find an access point with the same SSID. Set the computer, the access point, and the projector to the same SSID.
0892 The WPA/WPA2 authentication type does not match. Check that the wireless LAN security settings are correct.
s Security p.87
0893 The WEP/TKIP/AES encryption type does not match.
0894 Communication was disconnected because the projector connected to an
unauthorized access point.
Contact your network administrator for more information.
0898 Failed to acquire DHCP. Check that the DHCP server is operating correctly. If you are not using DHCP,
turn off the DHCP setting.
s Wireless LAN - IP Settings p.85
0899 Other communication errors If restarting the projector or EasyMP Network Projection does not solve the
problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
About Event ID
108
You should clean the projector if it becomes dirty or if the quality of
projected images starts to deteriorate.
Attention
Turn off the projector's power before cleaning.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing
a small amount of neutral detergent, and then firmly wring the cloth dry
before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the
projector's surface. The quality of the case may change or become discolored.
Cleaning the Lens
Use a commercially available cloth for cleaning glasses to gently wipe the
lens.
Warning
Do not use sprays that contain flammable gas to remove dust and lint from the
lens. The projector may catch fire due to the high internal temperature of the
lamp.
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it
can easily become damaged.
Cleaning the Air Filter
Clean the air filter and the air intake vent when the following message is
displayed.
"The projector is overheating. Make sure nothing is blocking the air vent,
and clean or replace the air filter."
Attention
If dust collects on the air filter, it can cause the internal temperature of the
projector to rise, and this can lead to problems with operation and shorten
the optical engine's service life. Clean the air filter immediately when the
message is displayed.
Do not rinse the air filter in water. Do not use detergents or solvents.
Cleaning
110
a
If a message is frequently displayed, even after cleaning, it is time to
replace the air filter. Replace it with a new air filter.
s "Replacing the Air Filter" p.116
It is recommended that you clean these parts at least once every
three months. Clean them more often than this if using the projector
in a particularly dusty environment.
Cleaning
111
e
Install the new lamp.
Insert the new Lamp along the guide rail in the correct direction so
that it fits in place, push in firmly, and once it is fully inserted
tighten the two screws.
f
Replace the lamp cover.
Attention
Make sure you install the lamp securely. If the lamp cover is removed, the
power turns off automatically as a safety precaution. If the lamp or the lamp
cover is not installed correctly, the power does not turn on.
This product includes a lamp component that contains mercury (Hg). Please
consult your local regulations regarding disposal or recycling. Do not dispose
of it with normal waste.
Resetting the lamp hours
The projector records how long the lamp is turned on and a message and
indicator notify you when it is time to replace the lamp. After replacing the
lamp, make sure you reset the Lamp Hours from the Configuration menu.
s "Reset Menu" p.92
a
Only reset the Lamp Hours after the lamp has been replaced.
Otherwise the lamp replacement period is not indicated correctly.
Replacing Consumables
115
Replacing the Air Filter
Air filter replacement period
It is time to replace the air filter when:
There is a tear in the air filter.
The message is displayed even though the air filter has been cleaned.
How to replace the air filter
The air filter can be replaced even when the projector is suspended from a
ceiling.
a
After you turn off the projector's power and the confirmation
buzzer beeps twice, disconnect the power cable.
b
Open the air filter cover.
Slide the air filter cover open/close switch, and open the air filter
cover.
c
Remove the air filter.
Grip the tab in the center of the air filter, and pull it straight out.
d
Install the new air filter.
Press until it clicks into place.
e
Close the air filter cover.
a
Dispose of used air filters properly in accordance with your local
regulations.
Material of the frame part: Polypropylene
Material of the filter part: Polypropylene
Replacing Consumables
116
Appendix
The following optional accessories and consumables are available. Please
purchase these products as and when needed. The following list of optional
accessories and consumables is current as of: October 2010. Details of
accessories are subject to change without notice and availability may vary
depending on the country of purchase.
Optional Accessories
Interactive Unit ELPIU01
Use when operating the computer screen on the projection surface.
Document Camera ELPDC06/ELPDC11
Use when projecting images such as books, OHP documents, or slides.
Soft carrying case ELPKS64
Use this case to carry the projector by hand.
50" portable screen ELPSC06
A compact screen that can be carried easily. (Aspect Ratio
g
4:3)
60" portable screen ELPSC27
80" portable screen ELPSC28
100" screen ELPSC29
Portable roll-type screens. (aspect ratio 4:3)
70" portable screen ELPSC23
80" portable screen ELPSC24
90" portable screen ELPSC25
Portable roll-type screens. (aspect ratio 16:10)
53" portable screen ELPSC30
64" portable screen ELPSC31
Portable magnetic screens. (aspect ratio 4:3)
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
This is the same as the computer cable supplied with the projector.
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Use one of these longer cables if the computer cable supplied with the projector
is too short.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male
^3)
Use to connect a component video
g
source.
Wireless LAN unit ELPAP07
Use when connecting the projector to a computer wirelessly and projecting.
Quick Wireless Connection USB Key ELPAP08
Use when you want to quickly establish one-to-one connection between the
projector and a computer with Windows installed.
Ceiling pipe (450 mm)
*
ELPFP13
Ceiling pipe (700 mm)
*
ELPFP14
Use when installing the projector on a high ceiling.
Ceiling mount
*
ELPMB23
Use when installing the projector on a ceiling.
* Special expertise is required to suspend the projector from a ceiling. Contact
your local dealer or the nearest address provided in the Epson Projector
Contact List.
s Epson Projector Contact List
Consumables
Lamp unit ELPLP60/ELPLP61
Use as a replacement for used lamps.
Air Filter ELPAF29
Use as a replacement for used air filters.
Optional Accessories and Consumables
118
Projection Distance (For EB-925/EB-905)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 83 - 136 -5
40" 81x61 111 - 182 -6
50" 100x76 140 - 229 -8
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 169 - 275 -10
80" 160x120 226 - 368 -13
100" 200x150 283 - 460 -16
150" 300x230 426 - 692 -24
200" 410x300 568 - 923 -32
250" 500x380 711 - 1155 -40
300" 610x457 854 - 1386 -48
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 91 - 149 +1
40" 89x50 122 - 199 +1
50" 110x62 153 - 249 +2
60" 130x75 184 - 300 +2
80" 180x100 246 - 401 +3
100" 220x120 308 - 502 +3
150" 330x190 464 - 754 +5
200" 440x250 619 - 1006 +7
250" 550x310 775 - 1258 +9
275" 609x343 853 - 1384 +10
Screen Size and Projection Distance
119
Projection Distance (For EB-915W)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 100 - 164 -1
40" 81x61 134 - 219 -2
50" 100x76 169 - 275 -2
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 203 - 331 -2
80" 160x120 271 - 442 -3
100" 200x150 340 - 553 -4
120" 244x183 408 - 664 -5
150" 300x230 511 - 831 -6
200" 410x300 682 - 1108 -8
250" 500x380 854 - 1386 -10
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 91 - 149 +1
40" 89x50 122 - 199 +1
50" 110x62 153 - 249 +2
60" 130x75 184 - 300 +2
80" 180x100 246 - 401 +3
100" 220x120 308 - 502 +3
150" 330x190 464 - 754 +5
200" 440x250 619 - 1006 +7
250" 550x310 775 - 1258 +9
275" 609x343 853 - 1384 +10
Screen Size and Projection Distance
120
Unit: cm
16:10 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 64x40 88 - 144 -1
40" 86x54 118 - 193 -1
50" 110x67 149 - 243 -2
60" 130x81 179 - 292 -2
80" 170x110 239 - 390 -3
100" 220x130 300 - 488 -3
150" 320x200 451 - 733 -5
200" 430x270 603 - 979 -7
250" 540x340 754 - 1224 -8
280" 605x377 845 - 1371 -9
Projection Distance (For EB-910W)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 76 - 91 -4
40" 81x61 102 - 122 -6
50" 100x76 127 - 153 -7
Screen Size and Projection Distance
121
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 153 - 184 -8
80" 160x120 205 - 246 -11
100" 200x150 256 - 308 -14
150" 300x230 385 - 462 -21
200" 410x300 514 - 617 -28
250" 500x380 643 - 771 -35
260" 520x400 668 - 802 -36
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 69 - 83 -2
40" 89x50 92 - 111 -2
50" 110x62 115 - 139 -3
60" 130x75 139 - 167 -3
70" 160x87 162 - 195 -4
80" 180x100 186 - 223 -5
100" 220x120 232 - 279 -6
150" 330x190 349 - 419 -8
200" 440x250 466 - 560 -11
250" 550x310 583 - 700 -14
280" 620x350 653 - 784 -16
Unit: cm
16:10 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 64x40 67 - 80 -4
40" 86x54 89 - 108 -5
50" 110x67 112 - 135 -6
60" 130x81 135 - 162 -7
80" 170x110 181 - 217 -10
100" 220x130 226 - 271 -12
150" 320x200 340 - 408 -18
200" 430x270 454 - 545 -24
250" 540x340 567 - 681 -31
300" 640x400 681 - 818 -37
Screen Size and Projection Distance
122
Projection Distance (For EB-900)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 72 - 86 -5
40" 81x61 96 - 116 -7
50" 100x76 120 - 145 -9
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 145 - 174 -10
80" 160x120 194 - 233 -14
100" 200x150 242 - 291 -17
150" 300x230 364 - 438 -26
200" 410x300 486 - 584 -34
250" 510x380 608 - 730 -43
300" 610x460 730 - 877 -51
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 78 - 94 +1
40" 89x50 105 - 126 +1
50" 110x62 131 - 158 +1
60" 130x75 158 - 190 +1
70" 160x87 185 - 222 +1
80" 180x100 211 - 254 +2
100" 220x120 264 - 317 +2
150" 330x190 397 - 477 +3
200" 440x250 530 - 636 +4
250" 550x310 663 - 796 +5
275" 610x340 729 - 875 +6
Screen Size and Projection Distance
123
Projection Distance (For EB-96W)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 94 - 113 -4
40" 81x61 126 - 152 -5
50" 100x76 158 - 190 -7
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 190 - 229 -8
70" 142x107 222 - 267 -10
80" 160x120 255 - 306 -11
100" 200x150 319 - 383 -14
150" 300x230 480 - 577 -20
200" 410x300 641 - 770 -27
280" 569x427 898 - 1079 -38
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
35" 78x44 99 - 120 -2
40" 89x50 114 - 137 -2
50" 110x62 143 - 172 -3
60" 130x75 172 - 208 -3
70" 160x87 202 - 243 -4
80" 180x100 231 - 278 -4
100" 220x120 289 - 348 -5
150" 330x190 435 - 523 -8
200" 440x250 582 - 699 -11
310" 686x386 903 - 1084 -17
Screen Size and Projection Distance
124
Unit: cm
16:10 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
35" 76x47 97 - 117 -4
40" 86x54 111 - 134 -5
50" 110x67 139 - 168 -6
60" 130x81 168 - 202 -7
80" 170x110 225 - 270 -10
100" 220x130 281 - 338 -12
150" 320x200 424 - 509 -18
200" 430x270 566 - 680 -24
320" 640x400 907 - 1089 -39
Projection Distance (For EB-95)
A
Projection distance
B
Distance from the center of the lens to the base of the screen
(or to the top of the screen, if suspended from a ceiling)
C
Center of lens
Unit: cm
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 61x46 89 - 107 -5
40" 81x61 119 - 143 -7
50" 100x76 150 - 180 -8
Screen Size and Projection Distance
125
4:3 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
60" 120x91 180 - 217 -10
80" 160x120 241 - 290 -14
100" 200x150 302 - 363 -17
150" 300x230 454 - 546 -25
200" 410x300 607 - 729 -34
250" 500x380 759 - 912 -42
300" 610x460 912 - 1095 -51
Unit: cm
16:9 Screen Size
A
B
Minimum (Wide) to Maximum
(Tele)
30" 66x37 97 - 117 +1
40" 89x50 130 - 156 +1
50" 110x62 163 - 196 +1
60" 130x75 196 - 236 +1
80" 180x100 263 - 316 +2
100" 220x120 329 - 396 +2
150" 330x190 495 - 595 +3
200" 440x250 661 - 794 +5
250" 550x310 827 - 994 +6
275" 620x350 910 - 1093 +6
Screen Size and Projection Distance
126
Supported Resolutions
Computer signals (analog RGB)
Signal Refresh Rate (Hz) Resolution (dots)
VGA 60/72/75/85 640x480
SVGA 56/60/72/75/85 800x600
XGA 60/70/75/85 1024x768
WXGA 60 1280x768
60 1360x768
60/75/85 1280x800
WXGA+ 60/75/85 1440x900
SXGA 70/75/85 1152x864
60/75/85 1280x1024
60/75/85 1280x960
SXGA+ 60/75 1400x1050
WSXGA+
*1, 2
60 1680x1050
UXGA 60 1600x1200
MAC13" 67 640x480
MAC16" 75 832x624
MAC19" 75 1024x768
59 1024x768
MAC21" 75 1152x870
*1
(EB-915W/EB-910W/EB-96W only)
*2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
Even when signals other than those mentioned above are input, it is likely that the
image can be projected. However, not all functions may be supported.
Component Video
Signal Refresh Rate (Hz) Resolution (dots)
SDTV (480i) 60 720x480
SDTV (576i) 50 720x576
SDTV (480p) 60 720x480
SDTV (576p) 50 720x576
HDTV (720p) 50/60 1280x720
HDTV (1080i) 50/60 1920x1080
Composite video
Signal Refresh Rate (Hz) Resolution (dots)
TV (NTSC) 60 720x480
TV (SECAM) 50 720x576
TV (PAL) 50/60 720x576
Input signal from the HDMI port
Signal Refresh Rate (Hz) Resolution (dots)
VGA 60 640x480
SVGA 60 800x600
XGA 60 1024x768
WXGA 60 1280x800
SXGA
60 1280x960
60 1280x1024
SXGA+ 60 1400x1050
UXGA 60 1600x1200
Supported Monitor Displays
127
Signal Refresh Rate (Hz) Resolution (dots)
SDTV (480i/480p) 60 720x480
SDTV (576i/576p) 50 720x576
HDTV (720p) 50/60 1280x720
HDTV (1080i) 50/60 1920x1080
HDTV (1080p) 24/30/50/60 1920x1080
Supported Monitor Displays
128
Projector General Specifications
Product name
EB-925 EB-915W EB-910W EB-905
Dimensions
345 (W) x 93 (H) x 263 (D) mm
LCD panel size
0.63" 0.59" Wide 0.59" Wide 0.63"
Display method
Polysilicon TFT active matrix
Resolution
786,432 pixels
XGA (1024 (W) x 768 (H)
dots)x 3
1,024,000 pixels
WXGA (1280 (W)x 800 (H)
dots)x 3
1,024,000 pixels
WXGA (1280 (W)x 800 (H)
dots)x 3
786,432 pixels
XGA (1024 (W) x 768 (H)
dots)x 3
Focus adjustment
Manual
Zoom adjustment
Manual (1 to 1.6) Manual (1 to 1.2) Manual (1 to 1.6)
Lamp
UHE lamp, 230 W Model No.: ELPLP61 UHE lamp, 200 W Model No.:
ELPLP60
Max. audio output
16 W
Speaker
1
Power supply
100-240 V AC ±10%, 50/60 Hz 3.6-1.6 A 100-240 V AC ±10%, 50/60 Hz
3.2-1.5 A
Power con-
sumption
100 to 120 V area
Operating: 355 W
Standby power consumption (Communication On): 8.9 W
Standby power consumption (Communication Off): 0.29 W
Operating: 313 W
Standby power consumption
(Communication On): 8.9 W
Standby power consumption
(Communication Off): 0.29 W
220 to 240 V area
Operating: 337 W
Standby power consumption (Communication On): 9.6 W
Standby power consumption (Communication Off): 0.39 W
Operating: 300 W
Standby power consumption
(Communication On): 9.6 W
Standby power consumption
(Communication Off): 0.39 W
Operating altitude
Altitude 0 to 2,286 m
Operating temperature
5 to +35°C (No condensation)
Storage temperature
-10 to +60°C (No condensation)
Specifications
129
Mass
Approx. 3.4 kg Approx. 3.2 kg Approx. 3.4 kg
Product name
EB-900 EB-96W EB-95
Dimensions
345 (W) x 93 (H) x 263 (D) mm
LCD panel size
0.55" 0.59" Wide 0.55"
Display method
Polysilicon TFT active matrix
Resolution
786,432 pixels
XGA (1024 (W) x 768 (H)
dots)x 3
1,024,000 pixels
WXGA (1280 (W)x 800 (H)
dots)x 3
786,432 pixels
XGA (1024 (W) x 768 (H)
dots)x 3
Focus adjustment
Manual
Zoom adjustment
Manual (1 to 1.2)
Lamp
UHE lamp, 200 W Model No.: ELPLP60
Max. audio output
16 W
Speaker
1
Power supply
100 to 240 V AC ±10%, 50/60
Hz 3.2 to 1.4 A
100 to 240 V AC ±10%, 50/60
Hz 3.2 to 1.5 A
100 to 240 V AC ±10%, 50/60
Hz 3.2 to 1.4 A
Power con-
sumption
100 to 120 V area
Operating: 312 W
Standby power consumption
(Communication On): 8.1 W
Standby power consumption
(Communication Off): 0.31 W
Operating: 313 W
Standby power consumption
(Communication On): 8.9 W
Standby power consumption
(Communication Off): 0.29 W
Operating: 312 W
Standby power consumption
(Communication On): 8.1 W
Standby power consumption
(Communication Off): 0.31 W
220 to 240 V area
Operating: 299 W
Standby power consumption
(Communication On): 8.8 W
Standby power consumption
(Communication Off): 0.40 W
Operating: 300 W
Standby power consumption
(Communication On): 9.6 W
Standby power consumption
(Communication Off): 0.39 W
Operating: 299 W
Standby power consumption
(Communication On): 8.8 W
Standby power consumption
(Communication Off): 0.40 W
Operating altitude
Altitude 0 to 2,286 m
Operating temperature
5 to +35°C (No condensation)
Storage temperature
-10 to +60°C (No condensation)
Specifications
130
Mass
Approx. 3.1 kg Approx. 3.3 kg Approx. 3.2 kg
Connectors Computer1 port 1
Mini D-Sub15-pin (female)
Computer2 port 1
Mini D-Sub15-pin (female)
Video port 1
RCA pin jack
S-Video port 1
Mini DIN 4-pin
Audio1 port 1
Stereo mini jack
Audio2 port 1
Stereo mini jack
Audio-L/R port 1
RCA pin jack x 2 (L-R)
Mic port 1
Stereo mini jack
Audio Out port 1
Stereo mini jack
Monitor Out port 1
Mini D-Sub15-pin (female)
HDMI port 1
HDMI (Audio is only supported by PCM)
USB(TypeA) port
*1
1
USB connector (Type A)
USB(TypeB) port
*1
1
USB connector (Type B)
USB port
(dedicated Wireless LAN unit)
1
USB connector (Type A)
LAN Port
*2
1
RJ-45
RS-232C port 1
Mini D-Sub 9-pin (male)
*1 Supports USB 2.0. However, USB ports are not guaranteed to operate all devices that support USB.
*2 EB-925/EB-915W/EB-905/EB-96W/EB-95 only.
Specifications
131
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 30˚ it could be damaged and cause an accident.
Specifications
132
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We: Epson America, Inc.
Located at: 3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
Tel: 562-290-5254
Declare under sole responsibility that the product identified herein,
complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital
device. Each product marketed, is identical to the representative unit tested
and found to be compliant with the standards. Records maintained continue
to reflect the equipment being produced can be expected to be within the
variation accepted, due to quantity production and testing on a statistical
basis as required by 47CFR 2.909. Operation is subject to the following two
conditions : (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that
may cause undesired operation.
Trade Name: EPSON
Type of Product: Projector
Model: H381C/H382C/H383C/H384C/H385C/H386C/
H387C/H388C/H389C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio or television
reception. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause interference to radio
and television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this
equipment will invalidate the FCC Certification or Declaration of this
device and may cause interference levels which exceed the limits established
by the FCC for this equipment. It is the responsibility of the user to obtain
and use a shielded equipment interface cable with this device. If this
equipment has more than one interface connector, do not leave cables
connected to unused interfaces. Changes or modifications not expressly
approved by the manufacturer could void the user's authority to operate the
equipment.
Specifications
133
EB-925/EB-915W/EB-905
A
Center of lens
B
Distance from center of lens to suspension bracket fixing point
Units: mm
Appearance
134
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
AMX Device Discovery
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
Aspect Ratio
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
Component Video
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
Composite video
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
Contrast
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to
make them appear softer. Adjusting this particular property of an image is called contrast adjustment.
DHCP
An abbreviation of Dynamic Host Configuration Protocol, this protocol automatically assigns an IP address
g
to equipment connected to a network.
Gateway Address
This is a server (router) for communicating across a network (subnet) divided according to subnet mask
g
.
HDCP
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting
digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.
HDTV
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
Vertical resolution of 720p or 1080i or greater (p =
Progressive
g
, i = Interlace
g
)
Screen
aspect ratio
g
of 16:9
Interlace
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
IP Address
A number to identify a computer connected to a network.
Progressive
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount
of flicker in images decreases because the volume of information has doubled compared with an interlace system.
SDTV
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV
g
High-
Definition Television.
SNMP
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and
computers connected to a TCP/IP network.
Glossary
136
sRGB
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by
computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source
to sRGB.
SSID
SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices that correspond
to SSID.
Subnet Mask
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
SVGA
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
S-Video
A method that separates the video signal into a luminance component (Y) and a color component (C).
SXGA
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
Sync.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
Tracking
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of
a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If Tracking is not carried
out correctly, wide vertical stripes appear in the signal.
Trap IP Address
This is the IP address
g
for the destination computer used for error notification in SNMP.
VGA
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
XGA
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
Glossary
137
All rights reserved. No part of this publication may be reproduced, stored in a retrieval
system, or transmitted in any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the
information contained herein. Neither is any liability assumed for damages resulting
from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this
product or third parties for damages, losses, costs, or expenses incurred by the
purchaser or third parties as a result of: accident, misuse, or abuse of this product or
unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and
maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising
from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
About Notations
Microsoft
®
Windows
®
98 operating system
Microsoft
®
Windows
®
Me operating system
Microsoft
®
Windows
®
2000 operating system
Microsoft
®
Windows
®
XP Professional operating system
Microsoft
®
Windows
®
XP Home Edition operating system
Microsoft
®
Windows Vista
®
operating system
Microsoft
®
Windows
®
7 operating system
In this guide, the operating systems above are referred to as "Windows 98",
"Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and
"Windows 7". Furthermore, the collective term Windows may be used to
refer to Windows 98, Windows Me, Windows 2000, Windows XP,
Windows Vista, and Windows 7, and multiple versions of Windows may be
referred to as, for example, Windows 98/Me/2000/XP/Vista, with the
Windows notation omitted.
Mac OS X 10.3.x
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.9", "Mac OS X 10.4.x", "Mac OS X 10.5.x", and "Mac OS X 10.6.x".
Furthermore, the collective term "Mac OS" is used to refer to them.
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corp.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo
are trademarks or registered trademarks of Microsoft Corporation in the United States
and/or other countries.
WPA
and WPA2
are registered trademarks of Wi-Fi Alliance.
HDMI and High-Definition Multimedia Interface are the trademarks or registered
trademarks of HDMI Licensing LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
Other product names used herein are also for identification purposes only and may be
trademarks of their respective owners. Epson disclaims any and all rights in those
marks.
©SEIKO EPSON CORPORATION 2010. All rights reserved.
General Notes
138
GNU GPL
This projector product includes the open source software programs which apply
the GNU General Public License Version 2 or later version ("GPL Programs").
We provide the source code of the GPL Programs until five (5) years after the
discontinuation of same model of this projector product.
If you desire to receive the source code of the GPL Programs, please see the
"EPSON Projector Contact List" in the User's Guide, and contact the customer
support of your region.
These GPL Programs are WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public License for more details.
The list of GPL Programs is as follows and the names of author are described in the
source code of the GPL Programs
The list of GPL Programs
busybox-1.13.4
iptables-1.4.4
libgcc1(gcc-4.3.3)
linux-2.6.27
patches
udhcp 0.9.8
uvc rev.219
wireless_tools 29
EPSON original drivers
The GNU General Public License Version 2 is as follows. You also can see the GNU
General Public License Version 2 at http://www.gnu.org/licenses/.
GNU GENERAL PUBLIC LICENSE
Version 2, June 1991
Copyright (C) 1989, 1991 Free Software Foundation, Inc., 51 Franklin Street, Fifth
Floor, Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute
verbatim copies of this license document, but changing it is not allowed.
Preamble
The licenses for most software are designed to take away your freedom to share and
change it. By contrast, the GNU General Public License is intended to guarantee your
freedom to share and change free software--to make sure the software is free for all its
users. This General Public License applies to most of the Free Software Foundation's
software and to any other program whose authors commit to using it. (Some other Free
Software Foundation software is covered by the GNU Lesser General Public License
instead.) You can apply it to your programs, too.
When we speak of free software, we are referring to freedom, not price. Our General
Public Licenses are designed to make sure that you have the freedom to distribute copies
of free software (and charge for this service if you wish), that you receive source code or
can get it if you want it, that you can change the software or use pieces of it in new free
programs; and that you know you can do these things.
To protect your rights, we need to make restrictions that forbid anyone to deny you
these rights or to ask you to surrender the rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the software, or if you modify it.
For example, if you distribute copies of such a program, whether gratis or for a fee, you
must give the recipients all the rights that you have. You must make sure that they, too,
receive or can get the source code. And you must show them these terms so they know
their rights.
We protect your rights with two steps: (1) copyright the software, and (2) offer you this
license which gives you legal permission to copy, distribute and/or modify the software.
Also, for each author's protection and ours, we want to make certain that everyone
understands that there is no warranty for this free software. If the software is modified
by someone else and passed on, we want its recipients to know that what they have is not
the original, so that any problems introduced by others will not reflect on the original
authors' reputations.
Finally, any free program is threatened constantly by software patents. We wish to avoid
the danger that redistributors of a free program will individually obtain patent licenses,
in effect making the program proprietary. To prevent this, we have made it clear that any
patent must be licensed for everyone's free use or not licensed at all.
The precise terms and conditions for copying, distribution and modification follow.
General Notes
139
GNU GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR COPYING,
DISTRIBUTION AND MODIFICATION
0. This License applies to any program or other work which contains a notice placed
by the copyright holder saying it may be distributed under the terms of this
General Public License. The "Program", below, refers to any such program or
work, and a "work based on the Program" means either the Program or any
derivative work under copyright law: that is to say, a work containing the Program
or a portion of it, either verbatim or with modifications and/or translated into
another language. (Hereinafter, translation is included without limitation in the
term "modification".) Each licensee is addressed as "you".
Activities other than copying, distribution and modification are not covered by
this License; they are outside its scope. The act of running the Program is not
restricted, and the output from the Program is covered only if its contents
constitute a work based on the Program (independent of having been made by
running the Program). Whether that is true depends on what the Program does.
1. You may copy and distribute verbatim copies of the Program's source code as you
receive it, in any medium, provided that you conspicuously and appropriately
publish on each copy an appropriate copyright notice and disclaimer of warranty;
keep intact all the notices that refer to this License and to the absence of any
warranty; and give any other recipients of the Program a copy of this License along
with the Program.
You may charge a fee for the physical act of transferring a copy, and you may at
your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Program or any portion of it, thus
forming a work based on the Program, and copy and distribute such modifications
or work under the terms of Section 1 above, provided that you also meet all of these
conditions:
a) You must cause the modified files to carry prominent notices stating that you
changed the files and the date of any change.
b) You must cause any work that you distribute or publish, that in whole or in
part contains or is derived from the Program or any part thereof, to be
licensed as a whole at no charge to all third parties under the terms of this
License.
c) If the modified program normally reads commands interactively when run,
you must cause it, when started running for such interactive use in the most
ordinary way, to print or display an announcement including an appropriate
copyright notice and a notice that there is no warranty (or else, saying that
you provide a warranty) and that users may redistribute the program under
these conditions, and telling the user how to view a copy of this License.
(Exception: if the Program itself is interactive but does not normally print
such an announcement, your work based on the Program is not required to
print an announcement.)
These requirements apply to the modified work as a whole. If identifiable sections
of that work are not derived from the Program, and can be reasonably considered
independent and separate works in themselves, then this License, and its terms, do
not apply to those sections when you distribute them as separate works. But when
you distribute the same sections as part of a whole which is a work based on the
Program, the distribution of the whole must be on the terms of this License, whose
permissions for other licensees extend to the entire whole, and thus to each and
every part regardless of who wrote it.
Thus, it is not the intent of this section to claim rights or contest your rights to work
written entirely by you; rather, the intent is to exercise the right to control the
distribution of derivative or collective works based on the Program.
In addition, mere aggregation of another work not based on the Program with the
Program (or with a work based on the Program) on a volume of a storage or
distribution medium does not bring the other work under the scope of this
License.
3. You may copy and distribute the Program (or a work based on it, under Section 2)
in object code or executable form under the terms of Sections 1 and 2 above
provided that you also do one of the following:
a) Accompany it with the complete corresponding machine-readable source
code, which must be distributed under the terms of Sections 1 and 2 above on
a medium customarily used for software interchange; or,
b) Accompany it with a written offer, valid for at least three years, to give any
third party, for a charge no more than your cost of physically performing
source distribution, a complete machine-readable copy of the corresponding
source code, to be distributed under the terms of Sections 1 and 2 above on a
medium customarily used for software interchange; or,
General Notes
140
c) Accompany it with the information you received as to the offer to distribute
corresponding source code. (This alternative is allowed only for
noncommercial distribution and only if you received the program in object
code or executable form with such an offer, in accord with Subsection b
above.)
The source code for a work means the preferred form of the work for making
modifications to it. For an executable work, complete source code means all the
source code for all modules it contains, plus any associated interface definition
files, plus the scripts used to control compilation and installation of the executable.
However, as a special exception, the source code distributed need not include
anything that is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating system on which
the executable runs, unless that component itself accompanies the executable.
If distribution of executable or object code is made by offering access to copy from
a designated place, then offering equivalent access to copy the source code from
the same place counts as distribution of the source code, even though third parties
are not compelled to copy the source along with the object code.
4. You may not copy, modify, sublicense, or distribute the Program except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense or distribute the Program is void, and will automatically terminate your
rights under this License. However, parties who have received copies, or rights,
from you under this License will not have their licenses terminated so long as such
parties remain in full compliance.
5. You are not required to accept this License, since you have not signed it. However,
nothing else grants you permission to modify or distribute the Program or its
derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Program (or any work based
on the Program), you indicate your acceptance of this License to do so, and all its
terms and conditions for copying, distributing or modifying the Program or works
based on it.
6. Each time you redistribute the Program (or any work based on the Program), the
recipient automatically receives a license from the original licensor to copy,
distribute or modify the Program subject to these terms and conditions. You may
not impose any further restrictions on the recipients' exercise of the rights granted
herein. You are not responsible for enforcing compliance by third parties to this
License.
7. If, as a consequence of a court judgment or allegation of patent infringement or for
any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not
distribute the Program at all. For example, if a patent license would not permit
royalty-free redistribution of the Program by all those who receive copies directly
or indirectly through you, then the only way you could satisfy both it and this
License would be to refrain entirely from distribution of the Program.
If any portion of this section is held invalid or unenforceable under any particular
circumstance, the balance of the section is intended to apply and the section as a
whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other
property right claims or to contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free software distribution system,
which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that
system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
8. If the distribution and/or use of the Program is restricted in certain countries
either by patents or by copyrighted interfaces, the original copyright holder who
places the Program under this License may add an explicit geographical
distribution limitation excluding those countries, so that distribution is permitted
only in or among countries not thus excluded. In such case, this License
incorporates the limitation as if written in the body of this License.
9. The Free Software Foundation may publish revised and/or new versions of the
General Public License from time to time. Such new versions will be similar in
spirit to the present version, but may differ in detail to address new problems or
concerns.
General Notes
141
Each version is given a distinguishing version number. If the Program specifies a
version number of this License which applies to it and "any later version", you have
the option of following the terms and conditions either of that version or of any
later version published by the Free Software Foundation. If the Program does not
specify a version number of this License, you may choose any version ever
published by the Free Software Foundation.
10. If you wish to incorporate parts of the Program into other free programs whose
distribution conditions are different, write to the author to ask for permission. For
software which is copyrighted by the Free Software Foundation, write to the Free
Software Foundation; we sometimes make exceptions for this. Our decision will be
guided by the two goals of preserving the free status of all derivatives of our free
software and of promoting the sharing and reuse of software generally.
NO WARRANTY
11. BECAUSE THE PROGRAM IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE PROGRAM, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
PROGRAM "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE PROGRAM IS WITH YOU. SHOULD THE
PROGRAM PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL
NECESSARY SERVICING, REPAIR OR CORRECTION.
12. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR REDISTRIBUTE THE PROGRAM AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE PROGRAM
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY
OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Programs
If you develop a new program, and you want it to be of the greatest possible use to the
public, the best way to achieve this is to make it free software which everyone can
redistribute and change under these terms.
To do so, attach the following notices to the program. It is safest to attach them to the
start of each source file to most effectively convey the exclusion of warranty; and each file
should have at least the "copyright" line and a pointer to where the full notice is found.
<one line to give the program's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This program is free software; you can redistribute it and/or modify it under the
terms of the GNU General Public License as published by the Free Software
Foundation; either version 2 of the License, or (at your option) any later version.
This program is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License
for more details.
You should have received a copy of the GNU General Public License along with this
program; if not, write to the Free Software Foundation, Inc., 51 Franklin Street,
Fifth Floor, Boston, MA 02110-1301 USA.
Also add information on how to contact you by electronic and paper mail.
If the program is interactive, make it output a short notice like this when it starts in an
interactive mode:
Gnomovision version 69, Copyright (C) year name of author Gnomovision comes
with ABSOLUTELY NO WARRANTY; for details type `show w'. This is free
software, and you are welcome to redistribute it under certain conditions; type
`show c' for details.
The hypothetical commands `show w' and `show c' should show the appropriate parts
of the General Public License. Of course, the commands you use may be called
something other than `show w' and `show c'; they could even be mouse-clicks or menu
items--whatever suits your program.
You should also get your employer (if you work as a programmer) or your school, if any,
to sign a "copyright disclaimer" for the program, if necessary. Here is a sample; alter the
names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the program
`Gnomovision' (which makes passes at compilers) written by James Hacker.
General Notes
142
<signature of Ty Coon>, 1 April 1989
Ty Coon, President of Vice
This General Public License does not permit incorporating your program into
proprietary programs. If your program is a subroutine library, you may consider it more
useful to permit linking proprietary applications with the library. If this is what you want
to do, use the GNU Lesser General Public License instead of this License.
GNU LGPL
This projector product includes the open source software programs which apply
the GNU Lesser General Public License Version 2 or later version ("LGPL
Programs").
We provide the source code of the LGPL Programs until five (5) years after the
discontinuation of same model of this projector product.
If you desire to receive the source code of the LGPL Programs, please see the
"EPSON Projector Contact List" in the User's Guide, and contact the customer
support of your region.
These LGPL Programs are WITHOUT ANY WARRANTY; without even the
implied warranty of MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. See the GNU General Public License for more details.
The list of LGPL Programs is as follows and the names of author are described in
the source code of the LGPL Programs.
LGPL Programs
glibc-2.8
SDL-1.2.13
SDL-Image
The GNU Lesser General Public License Version 2 is as follows. You also can see the
GNU Lesser General Public License Version 2 at http://www.gnu.org/licenses/.
GNU LESSER GENERAL PUBLIC LICENSE
Version 2.1, February 1999
Copyright (C) 1991, 1999 Free Software Foundation, Inc. 51 Franklin Street, Fifth Floor,
Boston, MA 02110-1301 USA Everyone is permitted to copy and distribute verbatim
copies of this license document, but changing it is not allowed.
[This is the first released version of the Lesser GPL. It also counts as the successor of the
GNU Library Public License, version 2, hence the version number 2.1.]
Preamble
The licenses for most software are designed to take away your freedom to share and
change it. By contrast, the GNU General Public Licenses are intended to guarantee your
freedom to share and change free software--to make sure the software is free for all its
users.
This license, the Lesser General Public License, applies to some specially designated
software packages--typically libraries--of the Free Software Foundation and other
authors who decide to use it. You can use it too, but we suggest you first think carefully
about whether this license or the ordinary General Public License is the better strategy to
use in any particular case, based on the explanations below.
When we speak of free software, we are referring to freedom of use, not price. Our
General Public Licenses are designed to make sure that you have the freedom to
distribute copies of free software (and charge for this service if you wish); that you
receive source code or can get it if you want it; that you can change the software and use
pieces of it in new free programs; and that you are informed that you can do these
things.
To protect your rights, we need to make restrictions that forbid distributors to deny you
these rights or to ask you to surrender these rights. These restrictions translate to certain
responsibilities for you if you distribute copies of the library or if you modify it.
For example, if you distribute copies of the library, whether gratis or for a fee, you must
give the recipients all the rights that we gave you. You must make sure that they, too,
receive or can get the source code. If you link other code with the library, you must
provide complete object files to the recipients, so that they can relink them with the
library after making changes to the library and recompiling it. And you must show them
these terms so they know their rights.
We protect your rights with a two-step method: (1) we copyright the library, and (2) we
offer you this license, which gives you legal permission to copy, distribute and/or
modify the library.
To protect each distributor, we want to make it very clear that there is no warranty for
the free library. Also, if the library is modified by someone else and passed on, the
recipients should know that what they have is not the original version, so that the
original author's reputation will not be affected by problems that might be introduced
by others.
General Notes
143
Finally, software patents pose a constant threat to the existence of any free program. We
wish to make sure that a company cannot effectively restrict the users of a free program
by obtaining a restrictive license from a patent holder. Therefore, we insist that any
patent license obtained for a version of the library must be consistent with the full
freedom of use specified in this license.
Most GNU software, including some libraries, is covered by the ordinary GNU General
Public License. This license, the GNU Lesser General Public License, applies to certain
designated libraries, and is quite different from the ordinary General Public License. We
use this license for certain libraries in order to permit linking those libraries into non-
free programs.
When a program is linked with a library, whether statically or using a shared library, the
combination of the two is legally speaking a combined work, a derivative of the original
library. The ordinary General Public License therefore permits such linking only if the
entire combination fits its criteria of freedom. The Lesser General Public License
permits more lax criteria for linking other code with the library.
We call this license the "Lesser" General Public License because it does Less to protect
the user's freedom than the ordinary General Public License. It also provides other free
software developers Less of an advantage over competing non-free programs. These
disadvantages are the reason we use the ordinary General Public License for many
libraries. However, the Lesser license provides advantages in certain special
circumstances.
For example, on rare occasions, there may be a special need to encourage the widest
possible use of a certain library, so that it becomes a de-facto standard. To achieve this,
non-free programs must be allowed to use the library. A more frequent case is that a free
library does the same job as widely used non-free libraries. In this case, there is little to
gain by limiting the free library to free software only, so we use the Lesser General Public
License.
In other cases, permission to use a particular library in non-free programs enables a
greater number of people to use a large body of free software. For example, permission
to use the GNU C Library in non-free programs enables many more people to use the
whole GNU operating system, as well as its variant, the GNU/Linux operating system.
Although the Lesser General Public License is Less protective of the users' freedom, it
does ensure that the user of a program that is linked with the Library has the freedom
and the wherewithal to run that program using a modified version of the Library.
The precise terms and conditions for copying, distribution and modification follow.
Pay close attention to the difference between a "work based on the library" and a "work
that uses the library". The former contains code derived from the library, whereas the
latter must be combined with the library in order to run.
GNU LESSER GENERAL PUBLIC LICENSE TERMS AND CONDITIONS FOR
COPYING, DISTRIBUTION AND MODIFICATION
0. This License Agreement applies to any software library or other program which
contains a notice placed by the copyright holder or other authorized party saying it
may be distributed under the terms of this Lesser General Public License (also
called "this License"). Each licensee is addressed as "you".
A "library" means a collection of software functions and/or data prepared so as to
be conveniently linked with application programs (which use some of those
functions and data) to form executables.
The "Library", below, refers to any such software library or work which has been
distributed under these terms. A "work based on the Library" means either the
Library or any derivative work under copyright law: that is to say, a work
containing the Library or a portion of it, either verbatim or with modifications
and/or translated straightforwardly into another language. (Hereinafter,
translation is included without limitation in the term "modification".)
"Source code" for a work means the preferred form of the work for making
modifications to it. For a library, complete source code means all the source code
for all modules it contains, plus any associated interface definition files, plus the
scripts used to control compilation and installation of the library.
Activities other than copying, distribution and modification are not covered by
this License; they are outside its scope. The act of running a program using the
Library is not restricted, and output from such a program is covered only if its
contents constitute a work based on the Library (independent of the use of the
Library in a tool for writing it). Whether that is true depends on what the Library
does and what the program that uses the Library does.
1. You may copy and distribute verbatim copies of the Library's complete source
code as you receive it, in any medium, provided that you conspicuously and
appropriately publish on each copy an appropriate copyright notice and
disclaimer of warranty; keep intact all the notices that refer to this License and to
the absence of any warranty; and distribute a copy of this License along with the
Library.
You may charge a fee for the physical act of transferring a copy, and you may at
your option offer warranty protection in exchange for a fee.
2. You may modify your copy or copies of the Library or any portion of it, thus
forming a work based on the Library, and copy and distribute such modifications
or work under the terms of Section 1 above, provided that you also meet all of these
conditions:
General Notes
144
If such an object file uses only numerical parameters, data structure layouts and
accessors, and small macros and small inline functions (ten lines or less in length),
then the use of the object file is unrestricted, regardless of whether it is legally a
derivative work. (Executables containing this object code plus portions of the
Library will still fall under Section 6.)
Otherwise, if the work is a derivative of the Library, you may distribute the object
code for the work under the terms of Section 6. Any executables containing that
work also fall under Section 6, whether or not they are linked directly with the
Library itself.
6. As an exception to the Sections above, you may also combine or link a "work that
uses the Library" with the Library to produce a work containing portions of the
Library, and distribute that work under terms of your choice, provided that the
terms permit modification of the work for the customer's own use and reverse
engineering for debugging such modifications.
You must give prominent notice with each copy of the work that the Library is used
in it and that the Library and its use are covered by this License. You must supply a
copy of this License. If the work during execution displays copyright notices, you
must include the copyright notice for the Library among them, as well as a
reference directing the user to the copy of this License. Also, you must do one of
these things:
a) Accompany the work with the complete corresponding machine-readable
source code for the Library including whatever changes were used in the work
(which must be distributed under Sections 1 and 2 above); and, if the work is
an executable linked with the Library, with the complete machine-readable
"work that uses the Library", as object code and/or source code, so that the
user can modify the Library and then relink to produce a modified executable
containing the modified Library. (It is understood that the user who changes
the contents of definitions files in the Library will not necessarily be able to
recompile the application to use the modified definitions.)
b) Use a suitable shared library mechanism for linking with the Library. A
suitable mechanism is one that (1) uses at run time a copy of the library
already present on the user's computer system, rather than copying library
functions into the executable, and (2) will operate properly with a modified
version of the library, if the user installs one, as long as the modified version is
interface-compatible with the version that the work was made with.
c) Accompany the work with a written offer, valid for at least three years, to give
the same user the materials specified in Subsection 6a, above, for a charge no
more than the cost of performing this distribution.
d) If distribution of the work is made by offering access to copy from a
designated place, offer equivalent access to copy the above specified materials
from the same place.
e) Verify that the user has already received a copy of these materials or that you
have already sent this user a copy.
For an executable, the required form of the "work that uses the Library" must
include any data and utility programs needed for reproducing the executable from
it. However, as a special exception, the materials to be distributed need not include
anything that is normally distributed (in either source or binary form) with the
major components (compiler, kernel, and so on) of the operating system on which
the executable runs, unless that component itself accompanies the executable.
It may happen that this requirement contradicts the license restrictions of other
proprietary libraries that do not normally accompany the operating system. Such a
contradiction means you cannot use both them and the Library together in an
executable that you distribute.
7. You may place library facilities that are a work based on the Library side-by-side in
a single library together with other library facilities not covered by this License,
and distribute such a combined library, provided that the separate distribution of
the work based on the Library and of the other library facilities is otherwise
permitted, and provided that you do these two things:
a) Accompany the combined library with a copy of the same work based on the
Library, uncombined with any other library facilities. This must be
distributed under the terms of the Sections above.
b) Give prominent notice with the combined library of the fact that part of it is a
work based on the Library, and explaining where to find the accompanying
uncombined form of the same work.
8. You may not copy, modify, sublicense, link with, or distribute the Library except as
expressly provided under this License. Any attempt otherwise to copy, modify,
sublicense, link with, or distribute the Library is void, and will automatically
terminate your rights under this License. However, parties who have received
copies, or rights, from you under this License will not have their licenses
terminated so long as such parties remain in full compliance.
General Notes
146
9. You are not required to accept this License, since you have not signed it. However,
nothing else grants you permission to modify or distribute the Library or its
derivative works. These actions are prohibited by law if you do not accept this
License. Therefore, by modifying or distributing the Library (or any work based on
the Library), you indicate your acceptance of this License to do so, and all its terms
and conditions for copying, distributing or modifying the Library or works based
on it.
10. Each time you redistribute the Library (or any work based on the Library), the
recipient automatically receives a license from the original licensor to copy,
distribute, link with or modify the Library subject to these terms and conditions.
You may not impose any further restrictions on the recipients' exercise of the
rights granted herein. You are not responsible for enforcing compliance by third
parties with this License.
11. If, as a consequence of a court judgment or allegation of patent infringement or for
any other reason (not limited to patent issues), conditions are imposed on you
(whether by court order, agreement or otherwise) that contradict the conditions of
this License, they do not excuse you from the conditions of this License. If you
cannot distribute so as to satisfy simultaneously your obligations under this
License and any other pertinent obligations, then as a consequence you may not
distribute the Library at all. For example, if a patent license would not permit
royalty-free redistribution of the Library by all those who receive copies directly or
indirectly through you, then the only way you could satisfy both it and this License
would be to refrain entirely from distribution of the Library.
If any portion of this section is held invalid or unenforceable under any particular
circumstance, the balance of the section is intended to apply, and the section as a
whole is intended to apply in other circumstances.
It is not the purpose of this section to induce you to infringe any patents or other
property right claims or to contest validity of any such claims; this section has the
sole purpose of protecting the integrity of the free software distribution system
which is implemented by public license practices. Many people have made
generous contributions to the wide range of software distributed through that
system in reliance on consistent application of that system; it is up to the author/
donor to decide if he or she is willing to distribute software through any other
system and a licensee cannot impose that choice.
This section is intended to make thoroughly clear what is believed to be a
consequence of the rest of this License.
12. If the distribution and/or use of the Library is restricted in certain countries either
by patents or by copyrighted interfaces, the original copyright holder who places
the Library under this License may add an explicit geographical distribution
limitation excluding those countries, so that distribution is permitted only in or
among countries not thus excluded. In such case, this License incorporates the
limitation as if written in the body of this License.
13. The Free Software Foundation may publish revised and/or new versions of the
Lesser General Public License from time to time. Such new versions will be similar
in spirit to the present version, but may differ in detail to address new problems or
concerns.
Each version is given a distinguishing version number. If the Library specifies a
version number of this License which applies to it and "any later version", you have
the option of following the terms and conditions either of that version or of any
later version published by the Free Software Foundation. If the Library does not
specify a license version number, you may choose any version ever published by
the Free Software Foundation.
14. If you wish to incorporate parts of the Library into other free programs whose
distribution conditions are incompatible with these, write to the author to ask for
permission. For software which is copyrighted by the Free Software Foundation,
write to the Free Software Foundation; we sometimes make exceptions for this.
Our decision will be guided by the two goals of preserving the free status of all
derivatives of our free software and of promoting the sharing and reuse of software
generally.
NO WARRANTY
15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO
WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY
APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING
THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE
LIBRARY "AS IS" WITHOUT WARRANTY OF ANY KIND, EITHER
EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND
PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY
PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY
SERVICING, REPAIR OR CORRECTION.
General Notes
147
16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO
IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY
WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS
PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING
ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES
ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY
(INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING
RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD
PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY
OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries
If you develop a new library, and you want it to be of the greatest possible use to the
public, we recommend making it free software that everyone can redistribute and
change. You can do so by permitting redistribution under these terms (or, alternatively,
under the terms of the ordinary General Public License).
To apply these terms, attach the following notices to the library. It is safest to attach them
to the start of each source file to most effectively convey the exclusion of warranty; and
each file should have at least the "copyright" line and a pointer to where the full notice is
found.
<one line to give the library's name and a brief idea of what it does.>
Copyright (C) <year> <name of author>
This library is free software; you can redistribute it and/or modify it under the
terms of the GNU Lesser General Public License as published by the Free Software
Foundation; either version 2.1 of the License, or (at your option) any later version.
This library is distributed in the hope that it will be useful, but WITHOUT ANY
WARRANTY; without even the implied warranty of MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public
License for more details.
You should have received a copy of the GNU Lesser General Public License along
with this library; if not, write to the Free Software Foundation, Inc., 51 Franklin
Street, Fifth Floor, Boston, MA 02110-1301 USA
Also add information on how to contact you by electronic and paper mail.
You should also get your employer (if you work as a programmer) or your school, if any,
to sign a "copyright disclaimer" for the library, if necessary. Here is a sample; alter the
names:
Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob' (a
library for tweaking knobs) written by James Random Hacker.
<signature of Ty Coon>, 1 April 1990
Ty Coon, President of Vice
That's all there is to it!
BSD License (Berkeley Software Distribution License)
This projector product includes the open source software program "University of
California, Berkeley License (Berkeley Software Distribution License)" which applies
the terms and conditions provided by owner of the copyright to the "BSD License".
The "BSD License" are WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of BSD License programs
busybox-1.13.4
License terms of conditions of each program which are provided by owner of the
copyright to the “BSD License” are as follows.
Copyright (c) The Regents of the University of California. All rights reserved.
This code is derived from software contributed to Berkeley by Kenneth Almquist.
Redistribution and use in source and binary forms, with or without modification, are
permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this list of
conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice, this
list of conditions and the following disclaimer in the documentation and/or other
materials provided with the distribution.
3. Neither the name of the University nor the names of its contributors may be used
to endorse or promote products derived from this software without specific prior
written permission.
General Notes
148
The Unix configuration script "configure" was produced with GNU Autoconf. It is
copyright by the Free Software Foundation but is freely distributable. The same holds
for its supporting scripts (config.guess, config.sub, ltconfig, ltmain.sh). Another
support script, install-sh, is copyright by M.I.T. but is also freely distributable.
It appears that the arithmetic coding option of the JPEG spec is covered by patents
owned by IBM, AT&T, and Mitsubishi. Hence arithmetic coding cannot legally be used
without obtaining one or more licenses. For this reason, support for arithmetic coding
has been removed from the free JPEG software. (Since arithmetic coding provides only a
marginal gain over the unpatented Huffman mode, it is unlikely that very many
implementations will support it.) So far as we are aware, there are no patent restrictions
on the remaining code.
The IJG distribution formerly included code to read and write GIF files. To avoid
entanglement with the Unisys LZW patent, GIF reading support has been removed
altogether, and the GIF writer has been simplified to produce "uncompressed GIFs".
This technique does not use the LZW algorithm; the resulting GIF files are larger than
usual, but are readable by all standard GIF decoders.
We are required to state that
"The Graphics Interchange Format(c) is the Copyright property of CompuServe
Incorporated. GIF(sm) is a Service Mark property of CompuServe Incorporated."
libpng
This projector product includes the open source software program "libpng" which
applies the terms and conditions provided by owner of the copyright to the "libpng".
The "libpng" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of libpng programs
libpng-1.2.7
License terms of conditions of each program which are provided by owner of the
copyright to the "libpng" are as follows.
For conditions of distribution and use, see copyright notice in png.h Copyright (c)
1998-2004 Glenn Randers-Pehrson (Version 0.96 Copyright (c) 1996, 1997 Andreas
Dilger) (Version 0.88 Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc.)
This copy of the libpng notices is provided for your convenience. In case of any
discrepancy between this copy and the notices in the file png.h that is included in the
libpng distribution, the latter shall prevail.
COPYRIGHT NOTICE, DISCLAIMER, and LICENSE:
If you modify libpng you may insert additional notices immediately following this
sentence.
libpng version 1.2.6, September 12, 2004, is Copyright (c) 2004 Glenn Randers-Pehrson,
and is distributed according to the same disclaimer and license as libpng-1.2.5 with the
following individual added to the list of Contributing Authors
Cosmin Truta
libpng versions 1.0.7, July 1, 2000, through 1.2.5 - October 3, 2002, are Copyright (c)
2000-2002 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-1.0.6 with the following individuals added to the list of
Contributing Authors
Simon-Pierre Cadieux
Eric S. Raymond
Gilles Vollant
and with the following additions to the disclaimer:
There is no warranty against interference with your enjoyment of the library or
against infringement. There is no warranty that our efforts or the library will fulfill
any of your particular purposes or needs. This library is provided with all faults,
and the entire risk of satisfactory quality, performance, accuracy, and effort is with
the user.
libpng versions 0.97, January 1998, through 1.0.6, March 20, 2000, are Copyright (c)
1998, 1999 Glenn Randers-Pehrson, and are distributed according to the same
disclaimer and license as libpng-0.96, with the following individuals added to the list of
Contributing Authors:
Tom Lane
Glenn Randers-Pehrson
Willem van Schaik
libpng versions 0.89, June 1996, through 0.96, May 1997, are Copyright (c) 1996, 1997
Andreas Dilger Distributed according to the same disclaimer and license as libpng-0.88,
with the following individuals added to the list of Contributing Authors:
John Bowler
Kevin Bracey
Sam Bushell
Magnus Holmgren
Greg Roelofs
Tom Tanner
General Notes
150
libpng versions 0.5, May 1995, through 0.88, January 1996, are Copyright (c) 1995, 1996
Guy Eric Schalnat, Group 42, Inc.
For the purposes of this copyright and license, "Contributing Authors" is defined as the
following set of individuals:
Andreas Dilger
Dave Martindale
Guy Eric Schalnat
Paul Schmidt
Tim Wegner
The PNG Reference Library is supplied "AS IS". The Contributing Authors and Group
42, Inc. disclaim all warranties, expressed or implied, including, without limitation, the
warranties of merchantability and of fitness for any purpose. The Contributing Authors
and Group 42, Inc. assume no liability for direct, indirect, incidental, special, exemplary,
or consequential damages, which may result from the use of the PNG Reference Library,
even if advised of the possibility of such damage.
Permission is hereby granted to use, copy, modify, and distribute this source code, or
portions hereof, for any purpose, without fee, subject to the following restrictions:
1. The origin of this source code must not be misrepresented.
2. Altered versions must be plainly marked as such and must not be misrepresented
as being the original source.
3. This Copyright notice may not be removed or altered from any source or altered
source distribution.
The Contributing Authors and Group 42, Inc. specifically permit, without fee, and
encourage the use of this source code as a component to supporting the PNG file format
in commercial products. If you use this source code in a product, acknowledgment is not
required but would be appreciated.
A "png_get_copyright" function is available, for convenient use in "about" boxes and the
like:
printf("%s",png_get_copyright(NULL));
Also, the PNG logo (in PNG format, of course) is supplied in the files "pngbar.png" and
"pngbar.jpg (88x31) and "pngnow.png" (98x31).
Libpng is OSI Certified Open Source Software. OSI Certified Open Source is a
certification mark of the Open Source Initiative.
Glenn Randers-Pehrson
glennrp@users.sourceforge.net
September 12, 2004
zlib
This projector product includes the open source software program "zlib" which applies
the terms and conditions provided by owner of the copyright to the "zlib".
The "zlib" are WITHOUT ANY WARRANTY; without even the implied warranty of
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of zlib programs
zlib-1.1.4
License terms of conditions of each program which are provided by owner of the
copyright to the “zlib” are as follows.
Copyright notice:
(C) 1995-1998 Jean-loup Gailly and Mark Adler
This software is provided 'as-is', without any express or implied warranty. In no
event will the authors be held liable for any damages arising from the use of this
software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim
that you wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is
not required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
Jean-loup Gailly
jloup@gzip.org
Mark Adler
madler@alumni.caltech.edu
If you use the zlib library in a product, we would appreciate *not* receiving lengthy legal
documents to sign. The sources are provided for free but without warranty of any kind.
The library has been entirely written by Jean-loup Gailly and Mark Adler; it does not
include third-party code.
General Notes
151
If you redistribute modified sources, we would appreciate that you include in the file
ChangeLog history information documenting your changes.
libmd5-rfc
This projector product includes the open source software program "libmd5-rfc" which
applies the terms and conditions provided by owner of the copyright to the "libmd5-
rfc".
The "libmd5-rfc" are WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of libmd5-rfc programs
libmd5-rfc
License terms of conditions of each program which are provided by owner of the
copyright to the "libmd5-rfc" are as follows.
Copyright (C) 1999, 2002 Aladdin Enterprises. All rights reserved.
This software is provided 'as-is', without any express or implied warranty. In no
event will the authors be held liable for any damages arising from the use of this
software.
Permission is granted to anyone to use this software for any purpose, including
commercial applications, and to alter it and redistribute it freely, subject to the
following restrictions:
1. The origin of this software must not be misrepresented; you must not claim
that you wrote the original software. If you use this software in a product, an
acknowledgment in the product documentation would be appreciated but is
not required.
2. Altered source versions must be plainly marked as such, and must not be
misrepresented as being the original software.
3. This notice may not be removed or altered from any source distribution.
L. Peter Deutsch ghost@aladdin.com
Independent implementation of MD5 (RFC 1321).
This code implements the MD5 Algorithm defined in RFC 1321, whose text is available
at
http://www.ietf.org/rfc/rfc1321.txt
The code is derived from the text of the RFC, including the test suite (section A.5) but
excluding the rest of Appendix A. It does not include any code or documentation that is
identified in the RFC as being copyrighted.
The original and principal author of md5.h is L. Peter Deutsch <ghost@aladdin.com>.
Other authors are noted in the change history that follows (in reverse chronological
order):
2002-04-13 lpd Removed support for non-ANSI compilers; removed
references to Ghostscript; clarified derivation from RFC 1321; now handles byte
order either statically or dynamically.
1999-11-04 lpd Edited comments slightly for automatic TOC extraction.
1999-10-18 lpd Fixed typo in header comment (ansi2knr rather than md5);
added conditionalization for C++ compilation from Martin Purschke
<purschke@bnl.gov>.
1999-05-03 lpd Original version.
mDNSResponder
This projector product includes the open source software program "mDNSResponder"
which applies the following license terms "Apache License Version 2.0, January 2004".
List of "mDNSResponder"
mDNSResponder-107.6 (only mDNSResponderPosix is used)
License terms “Apache License Version 2.0, January 2004" are as follows.
Apache License
Version 2.0, January 2004
http://www.apache.org/licenses/
TERMS AND CONDITIONS FOR USE, REPRODUCTION, AND DISTRIBUTION
1. Definitions.
"License" shall mean the terms and conditions for use, reproduction, and
distribution as defined by Sections 1 through 9 of this document.
"Licensor" shall mean the copyright owner or entity authorized by the copyright
owner that is granting the License.
"Legal Entity" shall mean the union of the acting entity and all other entities that
control, are controlled by, or are under common control with that entity. For the
purposes of this definition, "control" means (i) the power, direct or indirect, to
cause the direction or management of such entity, whether by contract or
otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding
shares, or (iii) beneficial ownership of such entity.
General Notes
152
"You" (or "Your") shall mean an individual or Legal Entity exercising permissions
granted by this License.
"Source" form shall mean the preferred form for making modifications, including
but not limited to software source code, documentation source, and configuration
files.
"Object" form shall mean any form resulting from mechanical transformation or
translation of a Source form, including but not limited to compiled object code,
generated documentation, and conversions to other media types.
"Work" shall mean the work of authorship, whether in Source or Object form,
made available under the License, as indicated by a copyright notice that is
included in or attached to the work (an example is provided in the Appendix
below).
"Derivative Works" shall mean any work, whether in Source or Object form, that is
based on (or derived from) the Work and for which the editorial revisions,
annotations, elaborations, or other modifications represent, as a whole, an
original work of authorship. For the purposes of this License, Derivative Works
shall not include works that remain separable from, or merely link (or bind by
name) to the interfaces of, the Work and Derivative Works thereof.
"Contribution" shall mean any work of authorship, including the original version
of the Work and any modifications or additions to that Work or Derivative Works
thereof, that is intentionally submitted to Licensor for inclusion in the Work by
the copyright owner or by an individual or Legal Entity authorized to submit on
behalf of the copyright owner. For the purposes of this definition, "submitted"
means any form of electronic, verbal, or written communication sent to the
Licensor or its representatives, including but not limited to communication on
electronic mailing lists, source code control systems, and issue tracking systems
that are managed by, or on behalf of, the Licensor for the purpose of discussing and
improving the Work, but excluding communication that is conspicuously marked
or otherwise designated in writing by the copyright owner as "Not a
Contribution."
"Contributor" shall mean Licensor and any individual or Legal Entity on behalf of
whom a Contribution has been received by Licensor and subsequently
incorporated within the Work.
2. Grant of Copyright License. Subject to the terms and conditions of this License,
each Contributor hereby grants to You a perpetual, worldwide, non-exclusive,
no-charge, royalty-free, irrevocable copyright license to reproduce, prepare
Derivative Works of, publicly display, publicly perform, sublicense, and distribute
the Work and such Derivative Works in Source or Object form.
3. Grant of Patent License. Subject to the terms and conditions of this License, each
Contributor hereby grants to You a perpetual, worldwide, non-exclusive, no-
charge, royalty-free, irrevocable (except as stated in this section) patent license to
make, have made, use, offer to sell, sell, import, and otherwise transfer the Work,
where such license applies only to those patent claims licensable by such
Contributor that are necessarily infringed by their Contribution(s) alone or by
combination of their Contribution(s) with the Work to which such
Contribution(s) was submitted. If You institute patent litigation against any entity
(including a cross-claim or counterclaim in a lawsuit) alleging that the Work or a
Contribution incorporated within the Work constitutes direct or contributory
patent infringement, then any patent licenses granted to You under this License
for that Work shall terminate as of the date such litigation is filed.
4. Redistribution. You may reproduce and distribute copies of the Work or
Derivative Works thereof in any medium, with or without modifications, and in
Source or Object form, provided that You meet the following conditions:
(a) You must give any other recipients of the Work or Derivative Works a copy
of this License; and
(b) You must cause any modified files to carry prominent notices stating that
You changed the files; and
(c) You must retain, in the Source form of any Derivative Works that You
distribute, all copyright, patent, trademark, and attribution notices from the
Source form of the Work, excluding those notices that do not pertain to any
part of the Derivative Works; and
(d) If the Work includes a "NOTICE" text file as part of its distribution, then any
Derivative Works that You distribute must include a readable copy of the
attribution notices contained within such NOTICE file, excluding those
notices that do not pertain to any part of the Derivative Works, in at least one
of the following places: within a NOTICE text file distributed as part of the
Derivative Works; within the Source form or documentation, if provided
along with the Derivative Works; or, within a display generated by the
Derivative Works, if and wherever such third-party notices normally appear.
The contents of the NOTICE file are for informational purposes only and do
not modify the License. You may add Your own attribution notices within
Derivative Works that You distribute, alongside or as an addendum to the
NOTICE text from the Work, provided that such additional attribution
notices cannot be construed as modifying the License.
General Notes
153
You may add Your own copyright statement to Your modifications and may
provide additional or different license terms and conditions for use, reproduction,
or distribution of Your modifications, or for any such Derivative Works as a
whole, provided Your use, reproduction, and distribution of the Work otherwise
complies with the conditions stated in this License.
5. Submission of Contributions. Unless You explicitly state otherwise, any
Contribution intentionally submitted for inclusion in the Work by You to the
Licensor shall be under the terms and conditions of this License, without any
additional terms or conditions.
Notwithstanding the above, nothing herein shall supersede or modify the terms of
any separate license agreement you may have executed with Licensor regarding
such Contributions.
6. Trademarks. This License does not grant permission to use the trade names,
trademarks, service marks, or product names of the Licensor, except as required
for reasonable and customary use in describing the origin of the Work and
reproducing the content of the NOTICE file.
7. Disclaimer of Warranty. Unless required by applicable law or agreed to in writing,
Licensor provides the Work (and each Contributor provides its Contributions) on
an "AS IS" BASIS, WITHOUT WARRANTIES OR CONDITIONS OF ANY
KIND, either express or implied, including, without limitation, any warranties or
conditions of TITLE, NON-INFRINGEMENT, MERCHANTABILITY, or
FITNESS FOR A PARTICULAR PURPOSE. You are solely responsible for
determining the appropriateness of using or redistributing the Work and assume
any risks associated with Your exercise of permissions under this License.
8. Limitation of Liability. In no event and under no legal theory, whether in tort
(including negligence), contract, or otherwise, unless required by applicable law
(such as deliberate and grossly negligent acts) or agreed to in writing, shall any
Contributor be liable to You for damages, including any direct, indirect, special,
incidental, or consequential damages of any character arising as a result of this
License or out of the use or inability to use the Work (including but not limited to
damages for loss of goodwill, work stoppage, computer failure or malfunction, or
any and all other commercial damages or losses), even if such Contributor has
been advised of the possibility of such damages.
9. Accepting Warranty or Additional Liability. While redistributing the Work or
Derivative Works thereof, You may choose to offer, and charge a fee for,
acceptance of support, warranty, indemnity, or other liability obligations and/or
rights consistent with this License. However, in accepting such obligations, You
may act only on Your own behalf and on Your sole responsibility, not on behalf of
any other Contributor, and only if You agree to indemnify, defend, and hold each
Contributor harmless for any liability incurred by, or claims asserted against, such
Contributor by reason of your accepting any such warranty or additional liability.
END OF TERMS AND CONDITIONS
APPENDIX: How to apply the Apache License to your work.
To apply the Apache License to your work, attach the following boilerplate notice,
with the fields enclosed by brackets "[]" replaced with your own identifying
information. (Don't include the brackets!) The text should be enclosed in the
appropriate comment syntax for the file format. We also recommend that a file or
class name and description of purpose be included on the same "printed page" as
the copyright notice for easier identification within third-party archives.
Copyright [yyyy][name of copyright owner]
Licensed under the Apache License, Version 2.0 (the "License");
you may not use this file except in compliance with the License.
You may obtain a copy of the License at
http://www.apache.org/licenses/LICENSE-2.0
Unless required by applicable law or agreed to in writing, software distributed under the
License is distributed on an "AS IS" BASIS, WITHOUT WARRANTIES OR
CONDITIONS OF ANY KIND, either express or implied.
See the License for the specific language governing permissions and limitations under
the License.
aes-src-29-04-09
This projector product includes the open source software program "aes-src-29-04-09"
which applies the terms and conditions provided by owner of the copyright to the "aes-
src-29-04-09".
The "aes-src-29-04-09" are WITHOUT ANY WARRANTY; without even the implied
warranty of MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
List of aes-src-29-04-09 programs
General Notes
154
aes-src-29-04-09
License terms of conditions of each program which are provided by owner of the
copyright to the “aes-src-29-04-09” are as follows.
Copyright (c) 1998-2008, Brian Gladman, Worcester, UK. All rights reserved.
LICENSE TERMS
The redistribution and use of this software (with or without changes) is allowed
without the payment of fees or royalties provided that:
1. source code distributions include the above copyright notice, this list of
conditions and the following disclaimer;
2. binary distributions include the above copyright notice, this list of
conditions and the following disclaimer in their documentation;
3. the name of the copyright holder is not used to endorse products built using
this software without specific written permission.
DISCLAIMER
This software is provided 'as is' with no explicit or implied warranties in respect of its
properties, including, but not limited to, correctness and/or fitness for purpose.
General Notes
155
A
A/V Mute ...................................................... 51
Abs. Color Temp. ........................................ 78
Air exhaust vent ........................................... 10
Air filter replacement period ................... 116
Aspect ...................................................... 42, 79
Auto H/V-Keystone .................................... 80
Auto Iris .................................................. 41, 78
Auto Setup .................................................... 78
B
Basic menu .................................................... 85
Blackboard .................................................... 41
Brightness ..................................................... 77
C
Ceiling ..................................................... 19, 82
Ceiling mount fixing points ....................... 12
Cleaning ...................................................... 110
Cleaning the air filter and air intake vent
........................................................................ 110
Cleaning the Projector's Surface .............. 110
Color Adjustment ........................................ 78
Color Mode ............................................ 40, 77
Color Saturation .......................................... 77
Computer Port ............................................. 11
Configuration menu .................................... 74
Connection mode ........................................ 86
Consumables .............................................. 118
Continuous ................................................... 50
Contrast ........................................................ 77
Control panel ............................................... 13
Control Panel Lock ............................... 61, 80
Crestron RoomView ................................... 69
Cross .............................................................. 53
D
Direct Power On .......................................... 82
Display ........................................................... 82
Display Background .................................... 82
Display order ................................................ 50
Display Settings ............................................ 50
Distance ...................................................... 119
Document Camera .................................... 118
Dynamic ........................................................ 40
E
EasyMP Monitor .......................................... 63
Email Address .............................................. 89
ESC/VP21 ..................................................... 67
Extended menu ............................................ 81
E-Zoom ......................................................... 53
F
Focus ring ..................................................... 10
Foot adjust lever ........................................... 10
Freeze ............................................................. 51
Front ........................................................ 19, 82
Front adjustable foot ................................... 10
Full Lock ....................................................... 61
G
Gateway Address ................................... 86, 88
H
HDMI port ................................................... 11
HDMI Video Range .................................... 79
Help function ............................................... 94
High Altitude Mode .................................... 82
How to replace the air filter ..................... 116
How to replace the lamp ........................... 113
I
Image menu .................................................. 77
Indicators ...................................................... 95
Info menu ..................................................... 91
Input Signal ............................................ 79, 91
IP Address ..................................................... 89
K
Keystone ........................................................ 80
L
Lamp cover ................................................... 10
Lamp hours ................................................... 91
Lamp indicator ............................................. 95
Lamp replacement period ........................ 112
Language ....................................................... 83
Lens Cover Timer ........................................ 82
M
Mail Notification ................................... 66, 89
Mail Notification menu .............................. 89
Message Broadcasting ................................. 63
Messages ....................................................... 82
Mic Input Level ............................................ 80
Index
156
Monitor Displays ....................................... 127
Mouse pointer .............................................. 54
N
Network Configuration .............................. 84
Network information .................................. 83
Network Menu ............................................. 83
Noise Reduction ........................................... 79
O
Operating temperature ..................... 129, 130
Operation ...................................................... 82
Optional accessories .................................. 118
Overheating .................................................. 96
P
Part Names and Functions ......................... 10
Password protect .......................................... 59
Password protect sticker ............................. 60
Pattern ........................................................... 81
Photo ............................................................. 41
PJLink ............................................................ 68
PJLink Password .......................................... 85
Plug-in Power ............................................... 83
Pointer ........................................................... 52
Pointer Shape ............................................... 80
Port Number ................................................ 89
Position ......................................................... 78
Power Consumption ................................... 80
Power indicator ............................................ 95
Power inlet .................................................... 11
Power On Protect ........................................ 59
Presentation ........................................... 41, 46
Problem Solving ........................................... 95
Progressive .................................................... 79
Projection ...................................................... 82
Projector keyword ....................................... 85
Projector Name ............................................ 85
Projector Setup ............................................. 63
Q
Quick Corner ............................................... 80
R
Reading Mail ................................................ 66
Rear .......................................................... 19, 82
Rear feet ........................................................ 12
Rear screen .................................................... 19
Refresh Rate .................................................. 91
Remote control ............................................ 14
Remote receiver ..................................... 10, 11
Replacing batteries ....................................... 16
Reset All ........................................................ 92
Reset menu ............................................. 91, 92
Resetting the lamp operating time
.................................................................. 92, 115
Resolution ..................................................... 91
RoomView .................................................... 69
Rotating images ........................................... 48
S
Screen size ................................................... 119
Screen switching time ................................. 50
Security menu .............................................. 87
Select Drive ................................................... 47
Settings menu ............................................... 80
Sharpness ...................................................... 77
Signal menu .................................................. 78
Sleep Mode ................................................... 82
Slideshow ................................................ 46, 49
SMTP Server ................................................. 89
SNMP ............................................................ 66
Soft keyboard ................................................ 84
Source ............................................................ 91
Source Search ......................................... 13, 31
Specifications ............................................. 129
Sports ............................................................. 41
sRGB .............................................................. 41
SSID ............................................................... 86
Standby Microphone ................................... 82
Standby Mode .............................................. 82
Startup Screen .............................................. 82
Storage temperature .......................... 129, 130
Subnet Mask ........................................... 86, 88
Supported Monitor Displays .................... 127
S-Video Port ................................................. 11
Sync Info ....................................................... 91
Sync. ............................................................... 78
T
Temp indicator ............................................ 95
Theatre .......................................................... 41
Tint ................................................................ 77
Tracking ........................................................ 78
U
USB Type B ................................................... 83
USB(TypeA) port ......................................... 11
USB(TypeB) port ......................................... 11
Index
157
User Button .................................................. 81
User Pattern .................................................. 57
User's Logo ................................................... 55
User's Logo Protect ...................................... 59
V
Video Port ..................................................... 11
Video Signal ........................................... 79, 91
Volume .......................................................... 80
Volume Button ............................................ 13
W
Web Browser ................................................ 63
Web Control ................................................. 64
Web Control Password ............................... 85
Web Remote ................................................. 64
Whiteboard ................................................... 41
Wired LAN Menu ........................................ 88
Wireless LAN indicator .............................. 10
Wireless LAN menu .................................... 85
Wireless LAN Power ................................... 85
Wireless LAN system .................................. 86
Wireless mouse function ............................ 54
Z
Zoom ring ..................................................... 10
Index
158
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Epson EB-910W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Epson EB-910W in the language / languages: English as an attachment in your email.

The manual is 12,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Epson EB-910W

Epson EB-910W User Manual - German - 166 pages

Epson EB-910W User Manual - Dutch - 164 pages

Epson EB-910W User Manual - French - 166 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info