680521
18
Zoom out
Zoom in
Previous page
1/56
Next page
18 / 56 MA120527=>2012-05 EasyLift 500 / Sesam 600
Installation must be performed by qualified service
technicians.
Work on the electrical installation must only be carried out by
authorised specialist personnel.
The load capacity and suitability of the supporting
construction of the building in which the door operator is to be
installed must be inspected and approved by an expert.
The door operator must be fully and securely attached at all
fastening points. All fastening materials must be selected
according to the nature of the supporting construction and
they must be able to withstand traction force of 900 N.
In the event of non-conformance with these
requirements, there is a risk of injury and material
damage caused by a falling operator or an uncontrolled
movement of the door.
When drilling the fastening holes, do not damage the building
structure or any electrical, water or other lines.
After lifting up the door operator to the ceiling, fasten it fully
with appropriate tools to prevent it from falling down.
Please observe appropriate industrial safety regulations and
keep children away during installation.
The door operator has the following safety devices. Do
not remove them or alter their functionality.
Automatic load switch-off during functions "OPEN" and
"CLOSE"
Connection for light barrier / safety edge / optosensor
Emergency lock release (see page 15 (N)
Checking Load Switch-off
The automatic load switch-off is a clamping and safety
mechanism that is designed to prevent accidents due to a
moving door.
Stop the door from outside with both hands at waist height.
When closing:
The door must stop automatically and reverse a little if it
comes into contact with an obstruction.
When opening:
The door must stop automatically if it comes into contact with
an obstruction.
Emergency Lock Release
Check as per the information provided on page 15 (N).
Additional Safety Devices
Check for proper functioning as per the manufacturer’s
instructions.
Signals of the indicator lamps 1 to 3
Please note: Check that the door is working properly
and running smoothly, and adjust if necessary. The
spring tension of the door must be set in such a way that it is
stable and can be opened and closed by hand smoothly and
without jolting.
Standard and appropriate shock-proof sockets approx. 10
- 50 cm near the fastening point at the head of the operator.
Only install the door operator in dry garages.
See instructions for installation from page 9.
Once installation is complete
connect the door to the door operator by: slowly opening
the door by hand until you hear the slide snap in.
Connect to the mains, LED 1 (red) flashes.
Teach in the door operator (see Chapter 15).
Teach in the remote transmitter (see Chapter 16).
Carry out a safety inspection (see Chapter 9).
7 Installation Precautions
8 Safety devices of the Door Operator
9 Safety Inspection
10 Controls and Indicators
1LED 1
2LED 2
3LED 3-6
10 POWER button
11 PROG button
12 CANC button
13 TEST button
3 Set force tolerance
1 + 2 Status during programming
11 Connections
4 Antenna
5+6 External switch
7-9 Light barrier
12 Installation Preparations
13 Installation
14 Commissioning
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Sesam 600 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Sesam 600 in the language / languages: English, German, French, Swedish as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info