680520

Entrematic EasyLift 500 Manual

20
Zoom out
Zoom in
Previous page
1/56
Next page
20 / 56 MA120527=>2012-05 EasyLift 500 / Sesam 600
External Pulse Input
An external pulse signal (e.g. wall button) can be connected
to terminals 8 and 9.
Automatic closing
If the automatic closing is activated, the door may only
be operated with an additional safety device.
Dip switch (14)
Set force tolerance:
After correct installation and correctly performed
teach in run, there is no need to change the force
tolerance. It is then set to value 4 (table 1).
If the force tolerance is changed, the door may only be
operated with an additional safety device and must be
subjected to a closing force test in accordance with DIN EN
12445 and DIN EN 12453.
• Using Dip switch (14), S2, select for what speed the force
tolerance is to be set.
ON = normal speed
OFF = soft run (slow)
• Press the POWER button (10) once, the LED‘s 3 (3-6)
indicate the set value as follows:
Table 1
• Set force tolerance by pressing the POWER button (10).
• Save the setting by pressing the CANC button (12).
Interference frequencies
The wireless signals of other 433.92 MHz transmitters can
interfere with the door operator.
Troubleshooting: Reset (Chapter 18) and then perform work
step Teaching in the Door Operator (Chapter 15)
If the error occurs again, request customer service.
Causes of Errors/Remedies
Changing the Battery of the Remote
Transmitter
Open the housing cover. Remove the battery, fit a new one
and replace the housing cover.
Use only leak-proof batteries. Make sure the polarity
is correct. Dispose of used batteries in an
environmentally-friendly way.
Monthly
• Load switch-off (entrapment protection device)
• Emergency lock release
• Additional safety devices (if fitted)
Every 6 months
• Mounting of door operator on the ceiling and on the wall
20 Additional Connections
21 Extended Settings
S1
ON
..Close after 3 minutes
OFF
22 Troubleshooting
Description Possible cause/Remedy
Entrapment
protection device not
working.
Incorrect setting of door or
entrapment protection device /
Reset and teach in again
The operator is not
working at all.
None or wrong voltage supply / The
fuse of the motor control is defective
/ Check external terminals 7 and 8.
The operator is
defective.
The slides are not snapped-in
properly./The chain is not tensioned
correctly./The door thresholds are
frozen.
The operator
switches off during
motion.
Check that the door is running
smoothly and that the entrapment
protection device is working properly
/ Reset / Teach in the door operator
The operator cannot
be used via the
remote transmitter
(optional).
Wireless signal level too weak.
Interfering wireless signals from
other transmission sources exist.
Battery weak
23 Maintenance Intervals
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic EasyLift 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic EasyLift 500 in the language / languages: English, German, French, Swedish as an attachment in your email.

The manual is 5,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info