609394

Entrematic Ditec DOITOB IP2015 Manual

11
Zoom out
Zoom in
Previous page
1/30
Next page
GB
11
DOITOB - IP2015
1. TECHNICAL DATA
DOIT OB DOIT OBJ
Power supply 24 V= 24 V=
Absorption 3 A 3 A
Thrust 1500 N 1500 N
Max run 350 mm 350 mm
Openingtime 25 s / 90° 25 s / 90°
Service class 3 - FREQUENT 3 - FREQUENT
Intermittence S2 = 30 min
S3 = 50%
S2 = 30 min
S3 = 50%
Temperature -20° C / +55° C -20° C / +55° C
Degreeofprotection IP54 IP54
Control panel E2H E2HJ
Applications
m = leaf width
kg = leaf weight
Recommended
dimensions
Limit dimensions
2. REFERENCE TO ILLUSTRATIONS
The given operating and performance features can only be gua-
ranteed with the use of DITEC accessories and safety devices.
2.1 Standardinstallationreferences(g.1)
[1] Radio
[2] Flashing light
[3] Key selector
[4] Connect power supply to a type-approved omnipolar switch
with a contact opening gap of no less that 3 mm (not sup-
plied by us) protected against accidental and unauthorized
activation.
[5] Right geared motor
[6] Left geared motor
[7] Photocells
[8] Control panel
2.2 Geared motor references
[9] Release
[10] Housing
[11] Draft tube
[12] Tube cover
[13] Closing plug
[14] Tail bracket
[15] Head bracket
3. INSTALLATION
Unless otherwise specied, all measurements are expressed
in millimetres (mm).
3.1 Preliminary checks
Check that the structure is sufciently rugged and that the hinge
pivots are properly lubricated. Provide an opening and closing
stop.
3.2 Geared motor installation
- Check the installation measurements (g.3) on the basis
of the distance between the hinge of the door wing and the
corner of the pillar [C] and of the desired opening angle [D].
- The geared motor is supplied as standard with right-hand
opening. To convert it for left-hand opening, proceed as
indicated in g.5.
- Loosen the motor fastening screws.
- Extract the motor and the reducer cap and unthread the
motor cable.
- Rotate the reduction gear by 180°.
- With the reduction gear rotated, insert the motor and cap,
and insert the cable.
Attention: the motor must be assembled so that the cable
remains on the side opposite the release.
- Insert and x the motor fastening screws.
- Fix the tail bracket [14], respecting measurements [A] and
[B] on the basis of the desired opening angle [D].
On the tail bracket there are holes that facilitate the as-
sembly operation.
Note: the installation measurements indicated in the table of g.3
allow you to choose the values of [A] and [B] on the basis of the
desired opening angle and in relation to the on site spaces and
overall dimensions.
Increasing [A] decreases the coming up speed during opening.
Increasing [B] decreases the coming up speed during closing
and improves burglar-proong.
Reducing [B] increases the extent of gate opening.
Measurements [A] and [B] must in any case be compatible with
the useful travel of the piston so that; if [A] is increased, [B] must
be decreased and vice versa.
- Fix the piston to the rear bracket [14] with the pin [F] sup-
plied (g.6).
- Extend the haulage tube completely [11] to its maximum
length, then shorten it by approximately 20mm (g.3).
Attention: the stops must keep a 10mm margin of tube
stroke, in both the door wing closed and door wing open
positions.
- With the gate completely closed, position the front bracket
500 kg
400 kg
300 kg
200 kg
100 kg
m12345
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entrematic Ditec DOITOB IP2015 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entrematic Ditec DOITOB IP2015 in the language / languages: English, German, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 4,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info