492809
26
Zoom out
Zoom in
Previous page
1/26
Next page
URC 4 User’s Guide
Copyright
2012 Entone, Inc. All rights reserved
.
25
v2.5 for URC 4
Appendix B Other Features
Showing URC 4 Firmware Version
The URC 4 firmware version is in the format of x.y.z, where x, y and z is digit 0-9. Use the following
procedures to show the URC 4 firmware version:
1. Press STBand hold for 5s. The STB backlight will illuminate.
2. Press INFO” once.
3. The 3 digits of the firmware version (x, y and z as described above) will be displayed in the following
manner.
a. TheSTB” backlight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2, etc
until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink.
b. In between each digit, the STBbacklight will be off for 1 second.
c. For example, the following blink pattern shows a firmware version of 2.0.4.
. . .-.-.- ....
NOTE: In the programming mode if no key is received within 30s, the device mode key backlight will blink
rapidly for 7 times to indicate an error and then extinguish, and the programming mode will end.
In addition, the URC 4 Firmware version will also be shown on the sticker inside the battery compartment at
the back of the remote control.
Showing Programmed Device Code
You can display the 4-digit device code by the following procedures:
1. Press and hold TV or “AUX for 5 seconds. The TVorAUXbacklight will illuminate.
2. Press INFO” once.
3. The 4-digits device code will be displayed in the following manner.
a. TheTV”/AUXbacklight blinks to indicate the digit. One blink indicates 1, 2 blinks indicates 2,
etc until 9 blinks indicates 9. A 0 is indicates by a shot, long, short, long, short, long blink.
b. In between each digit, the TV”/AUXbacklight will be off for 1 second.
c. For example, the following blink pattern shows a device code of 0123.
.-.-.- . .. ...
NOTE: In the programming mode if no key is received within 30s, the device mode key backlight will blink rapidly for 7
times to indicate an error and then extinguish, and the programming mode will end.
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entone URC 4 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entone URC 4 in the language / languages: English as an attachment in your email.

The manual is 0,46 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info