632470

Entone Kamai 400 series Manual

5
Zoom out
Zoom in
Previous page
1/27
Next page
Kamai Hybrid TV Receiver User’s Guide
3
Copyright
2011 Entone, Inc. All rights reserved.
IEEE 802.11b or 802.11g operation of this product in the U.S.A. is firmware-limited to channels
1 through 11.
This device is intended only for OEM integrators under the following conditions:
1) The transmitter module may not be co-located with any other transmitter or antenna,
2) For all products market in US, OEM has to limit the operation channels
in CH1 to CH11 for 2.4G band by supplied firmware programming tool.
OEM shall not supply any tool or info to the end-user regarding to
Regulatory Domain change.
As long as 2 conditions above are met, further transmitter test will not be
required. However, the OEM integrator is still responsible for testing their
end-product for any additional compliance requirements required with this
module installed (for example, digital device emissions, PC peripheral
requirements, etc.).
IMPORTANT NOTE: In the event that these conditions can not be met (for example certain
laptop configurations or co-location with another transmitter), then the FCC authorization is no
longer considered valid and the FCC ID can not be used on the final product. In these
circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization.
End Product Labeling
The final end product must be labeled in a visible area with the following: “Contains TX FCC ID:
RRK-WMPN12A1”.
Manual Information To the End User
The OEM integrator has to be aware not to provide information to the end
user regarding how to install or remove this RF module in the user’s
manual of the end product which integrates this module.
The end user manual shall include all required regulatory
information/warning as show in this manual.
Entone products are designed and tested to meet IEC60065, the
standard for the Safety of Information Technology Equipment. This is the
international standard for these types of products to reduce the risk of
product damage and of personal injury. The standard protects against
the following hazards:
• Electric shock
• Hazardous voltage levels
• Fire — Overload, temperature, material flammability
• Energy — Circuit with high energy or potential as burn hazards
• Heat — Accessible part of the product at high temperatures
• Radiation
• Noise
Canada Certification Notice The Industry Canada label identifies certified
equipment. This certification means that the equipment meets certain
telecommunications network protective operations and safety
requirements as prescribed in the appropriate Terminal Equipment
Technical Requirements document(s). The department does not
guarantee the equipment will operate to the user’s satisfaction. This
equipment meets the applicable Industry Canada Terminal Equipment
Technical Specification. This is confirmed by the registration number. The
abbreviation, IC, before the registration number signifies that registration
was performed based on a Declaration of Conformity indicating that
Industry Canada technical specifications were met. It does not imply that
Industry Canada approved the equipment. The Ringer Equivalence
Number (REN) is 0.0. The Ringer Equivalence Number that is assigned
to each piece of terminal equipment provides an indication of the
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Entone Kamai 400 series at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Entone Kamai 400 series in the language / languages: English as an attachment in your email.

The manual is 0,51 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info