729077
29
Zoom out
Zoom in
Previous page
1/38
Next page
57
Broadcast through PBX
1. DuraFon PRO and DuraWalkie both have the broadcast function,
each can broadcast another handset without going through the
base station, as long as the handsets are connecting. However,
when setting up the multi-base, the broadcast feature may not be
available due to the coverage range. In that case, you can use the
function of “Broadcast through PBX
” to broadcast.
2. From an administrator handset (Handset 10 or 11), press
MENU
(Right) soft key.
3.
Press number
9
, this will enter administration
menu.
4.
Press number
2
, handset enters Line setting menu.
a.
Enter Base ID(00~07) to access base.
b.
Press
1
to enter Broadcast setting
i. Press or to select L3 or L4 (the status of setting
will be displayed on LCD)
ii. Press CHANGE to enter the setting mode, and the base ID
will be displayed on LCD.
iii. Press On (Left soft key) to enable the broadcast function.
Press Off (Right soft key) to disable the broadcast function.
iv. After setting broadcast, press On (Left soft key) to enable
the AA. Press Off (Right soft key) to disable the AA. This AA
will prompt a greeting message to enter a two-digit
number (“01” ~ “07” for Group ID: “10” ~ “99” for Handset
ID: “00” for all).
Re: L3 and L4 can be setting as two broadcast lines, repeated
a
bove items for setting 2
nd
broadcast line.
5. When calling through the line 3 or 4, the caller will be prompt ed
by the greeting message to enter a two-digit extension number
( “01” ~ “07”
for Group ID: “10” ~ “99” for Handset ID: “00” for all).
a. The greeting message : “Please enter broadcast ID or wait for
a tone to page all
b. If there is no entry after 5 seconds, the broadcast will be
enable
d
to all handsets.
58
Note
1. Line 3 and/or 4 can be reserved for broadcast function.
2. When enable the broadcast function, each line (either Line 3 or 4)
will take two time slots for one single call.
3. When configuring a base with a single broadcast port (e.g. line 3),
the feasible simultaneous call will be line 1, line 2 and line 3, the
line 4 will not be able to make or receive call.
4. When configuring a base with dual broadcast ports, if line 3 and 4
are making broadcast, at the same time, the line 1 and line 2 are no
longer to make or receive calls.
5. Broadcast is limited to 30 seconds.
Repeater Operation
1. Due to the range performance of handset to handset calls
(intercom or broadcast) isn’t as good as line calls, in order to get
better range performance for handset to handset calls, install a
specialty repeater base and make the digital two-way radio calls
via the repeater for optimal performance.
Re: the
Repeater
requires specialty base unit
.
2.
The procedure of repeaters registration is same as the multi-base
which can be performed by administrator handset (Handset 10
and 11)
.
3.
From an administrator handset (Handset 10 or 11), press MENU
7 to enter the “BC/INT Type” menu setting.
4.
Press or key to select “Repeater Mode”, then press
SAVE (Left soft key)to confirm the selection.
Re : When setting to “Repeater” mode, the handset to handset
calls will always via repeater.
5.
Enter the base number (00~07) which assigned the base to be a
repeater.
6.
The default of “BC/INT Type” is “P2P Mode”
.
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Engenius DuraFon PRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Engenius DuraFon PRO in the language / languages: English as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info