660386
6
Zoom out
Zoom in
Previous page
1/15
Next page
• 6 •
10. CONTROL PANEL
LED Indicators (All Models)
CHECK (red) LED lit: Indicates that the battery is not properly connected to the charger.
CHECK (red) LED ashing: Indicates that the charger is in abort mode.
CHARGING (yellow) LED lit: Indicates that the charger has detected a battery and
is charging it.
CHARGED (green) LED lit: Indicates that the battery is fully charged and the
charger is in maintain mode.
NOTE: See the Operating Instructions section for a complete description of the
charger modes.
Display Button (Models OMAX-12A-1B, OMAX-25A-1B)
Press this button to set the digital display to show one of the following.
Battery % – The display shows an estimate of the percent of charge of the battery
connected to the charger battery clamps.
Voltage – The display shows the voltage at the battery clamps in DC volts.
Display Button (Models OMAX-50A-1B, OMAX-40AS-3B, OMAX-50AS-3B)
Press this button to set the digital display to show one of the following.
Percent: The display shows an estimate of the percent of charge of the battery
connected to the charger battery clamps.
Volts: The display shows the voltage at the battery clamps in DC volts.
Amps: The display shows charge current provided by the charger in DC amps.
Charge Button (Models OMAX-6A-1B, OMAX-12A-1B, OMAX-25A-1B)
Press this button to set the charger to one of the following settings.
On: Indicates the charger is in charge mode.
Off: Indicates the charger is in test mode.
Output Button (Model OMAX-50A-1B)
Press this button to set the charger to one of the following settings.
On: Indicates the charger is in charge mode.
Off: Indicates the charger is in test mode.
Bank Button (Models OMAX-40AS-3B, OMAX-50AS-3B)
Press this button to set the charger to one of the following settings for each bank.
Charge: Indicates that bank is in charge mode.
Test: Indicates that bank is in test mode.
11. OPERATING INSTRUCTIONS
This battery charger must be properly assembled in accordance with the
assembly instructions before it is used.
Charging
1. Make sure that you have an Odyssey
®
battery.
2. Ensure that all of the charger components are in place and in good working
condition, for example, the plastic boots on the battery clips.
3. Connect the battery following the precautions listed in sections 6 and 7.
4. Connect the AC power following the precautions listed in section 8. Make sure to
place the charger on a dry, non-ammable surface like metal or concrete.
5. Select the appropriate settings for your battery.
6. To disconnect, reverse the procedure.
NOTE: Do not connect one OMAX-40AS-3B or OMAX-50AS-3B sequencing charger
to two or more batteries connected in a series. If the positive terminal of one battery is
connected to the negative terminal of another battery, then they are connected in a series
and must not be connected to the same OMAX-40AS-3B or OMAX-50AS-3B charger.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enersys ODYSSEY Ultimizer Omax Batteries at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enersys ODYSSEY Ultimizer Omax Batteries in the language / languages: English as an attachment in your email.

The manual is 1,05 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info