717996
9
Zoom out
Zoom in
Previous page
1/72
Next page
9
EN
SL
HR
BS
SR
Belt adjustment
Belt adjustment and tension performs two functions: adjustment for tension and centering. The running belt has been
adjusted properly at the factory. However transportation, uneven flooring or other unpredicted reasons could cause
the belt to shift off center resulting in the belt rubbing with the plastic side rail or end caps and possibly causing dam-
age. To adjust the belt back to its proper position please follow the directions below:
Walking belt has shifted to the left: First unplug the power cord from the surge protector. Using the hex key pro-
vided, turn the left rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 4 km/h (2.5 mph). You should see the belt start to correct itself, moving back
towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking
belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to
the Walking belt slipping” instructions.
Walking belt has shifted to the right: First unplug the power cord from the surge protector. Using the hex key pro-
vided, turn the right rear roller adjustment bolt 1/4 turn in the clockwise direction. Plug the power cord back into the
surge protector and run the treadmill at 4 km/h (2.5 mph). You should see the belt start to correct itself, moving back
towards the center. Repeat the above procedure until the walking belt is centered. It may be necessary to set walking
belt tension once you have completed this procedure if the belt feels like it is slipping while walking. Refer below to
the Walking belt slipping” instructions.
Walking belt is slipping: First unplug the power cord from the surge protector. Using the hex key provided, turn
both the left and right rear roller adjustment bolts the same distance, usually a 1/4 turn in the clockwise direction.
Plug the power cord back into the surge protector and run the treadmill at 4 km/h (2.5 mph). You should now walk on
the belt to determine if the belt is still slipping. Repeat the above procedure until the walking belt is not slipping. The
tension should be just tight enough not to slip.
WARNING! Do not over tighten rollers! This will cause premature roller bearing failure!
Right and left tension bolts are located at the rear of the treadmill.
9


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Energetics PR 9.9hrc at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Energetics PR 9.9hrc in the language / languages: English as an attachment in your email.

The manual is 8,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info