ENDURO® EM315 35
Ref: EM315-UM-TKI-0323-Rev.B.
The slide switch (Fig. 8A) also acts as an “Emergency stop”.
The automatic engaging system:
To activate the automatic engaging system of the motor powered rollers on the tyre, press the two buttons for
engaging (Fig. 8L) or disengaging (Fig. 8M) for at least three seconds. The engaging icon (Fig. 8N) or
disengaging icon (Fig. 8O) will blink fast during these three seconds and every second there will be a beep. This
warns you that the system will be activated!
Engaging: After these three seconds the motor powered rollers will be pressed against the tyre, and the
engaging icon will illuminate constant. Now you can release the two buttons. When the motor powered rollers
are pressed on the tyre strongly enough you hear a short beep, the engaging icon will switch off and the
system is ready to use.
Disengaging: after these three seconds the motor powered rollers will be released from the tyre, and the
disengaging icon will illuminate constant. Now you can release the two buttons. When the motor powered
rollers are completely disengaged you hear a short beep, the disengaging icon will switch off and the system is
ready for transport.
The remote hand set switches off:
After 3 minutes, if no button is pressed: After 2 minutes the buzzer will beep for 5 times with a repetition
after 3 minutes. Than the system switches in the “stand-by” modes.
After 6 minutes, if one of the movement buttons is permanently held down: After 5 minutes the buzzer will
beep for 5 times with a repetition after 6 minutes. Than the system switches in the “stand-by” modes.
The screen goes off and the remote handset is in the “stand-by” modes which means that there always will be
used some current which causes the battery to go down. So always make sure the remote handset is turned off
by the slide switch.
To reactivate the remote handset, move slide switch to “Off” –O and then back to “On”-I after approximately 1
second.
Error messages via the remote handset:
Error messages of the ENDURO® EM315 will be communicated via the remote handset by the communication
icon (Fig. 8H), the error message icon’s (Fig. 8I, J, K) and a buzzer signal:
Communication icon (Fig. 8H) off, no buzzer: remote handset is turned off and also system is not activated
Communication icon (Fig. 8H) continue on, no buzzer: remote handset is turned on and system is activated
and ready to use.
Communication icon (Fig. 8H) is blinking, no buzzer: no communication between remote handset and
control unit. This could be because of too much distance between remote handset and control unit, or the
battery isolation switch for manoeuvring system is not turned on or that there is a distortion signal
disturbing the communication. As soon as connection is good again the communication icon will be
continue on and the system is ready to use.
Caravan battery voltage icon (Fig. 8K) is blinking in combination with buzzer (2 times blinking, break, 2
times blinking, break etc.): Battery voltage too low (<10 Volt). Battery needs to be recharged.
Caravan battery voltage icon (Fig. 8K) is blinking in combination with buzzer (4 times blinking, break, 4
times blinking, break etc.): Battery Voltage too high (over charged). Try to discharge the battery by
turning on a user (for example a lamp or water-pump).
Overload icon (Fig. 8I) is blinking in combination with buzzer (6 times blinking, break, 6 times blinking,
break etc.): Amp overload protection is activated. Wait about 60 seconds and try again.
Remote battery icon (Fig. 8J) is blinking, no buzzer: The 1.5 Volt batteries are nearly empty and need to
be replaced.
Changing batteries in the remote handset:
When the batteries are empty (Remote battery icon (Fig. 8J) is blinking), they need to be replaced.
Open the rear cover of the remote handset (Fig. 9).
Take out the dead/old batteries and dispose in the appropriate way.
Install a new replacement batteries (Fig. 9). Make sure to use leak proof AAA (1.5 Volt) batteries (No
claims under guarantee can be considered for damage caused by leaking batteries).
Close the rear cover again.
Dead and used batteries may leak and damage the remote handset! Remove the batteries if the remote
handset is not going to be used for an extended period.
