601366

Enduro EM305 Manual

35
Zoom out
Zoom in
Previous page
1/60
Next page
ENDURO
®
EM305 29
Ref: EM305-UM-TKI-0115-Rev.A.
Check the minimal installation dimensions of the manoeuvring system based on figure 14.
Only use adapters and accessories that are supplied or recommended by the manufacturer.
Check that the caravan is disconnected from the battery supply and the mains electrical supply.
Check that the tyres are not over worn and do have the same size and design (fitting to new or nearly new
tyres is the best option).
Make sure that the tyre-pressures are correct to the manufacturer’s recommendation.
Make sure the chassis is in good condition without any damage and is free from rust, dirt etc.
Stop work immediately if you are in doubt about the assembly or any procedures and consult one of our
engineers (Please refer to contact information on the last page of this manual).
Locate the battery isolation switch to be accessible at all times when parking and moving the caravan.
Do not remove, change or alter any parts of the chassis, axle, suspension or brake mechanism. Any drilling of
holes in the chassis is not allowed.
Do not install the unit if you are under the influence of drugs, alcohol or medication that could impair your
ability to use the equipment safely.
INSTALLATION - MECHANICAL COMPONENTS
FOR PROFESSIONAL INSTALLATION ONLY! These instructions are for general guidance.
Installation procedures may vary depending on caravan type.
Working under a vehicle without appropriate support is extremely dangerous!
Please refer to figure 13 for an overview of the whole assembly fully fitted.
Place the caravan on a hard, level surface. The use of a lifting ramp or an assembly pit is ideal for access and
personal safety.
Unpack all the components and check for the presence of all parts (see package contents list). Write down, on
the product warranty registration card, the 10-digit serial number (this is located on an aluminium plate on the
side of one of the motor units).
Clean the area of your chassis where you need to mount all components to ensure a good fitting.
Make sure the caravan is prepared for installation. Check before installation that important areas, such as
drains/spare tyre etc. do not cause any obstruction to the function of the caravan manoeuvring system.
Ensure both rollers are in the DISENGAGED position (Fig. 10), as the unit will not fit correctly otherwise (Note:
when fully disengaged, the pointer is positioned in the beginning of the yellow area).
Loosely assemble the left hand motor unit (1), right hand motor unit (2) and main cross bar (3) (Fig. 1). The
nuts (Fig. 1A), on the cross bar (3) to secure both motor units, must be no more than finger-tight at this stage.
Note: In principle, the unit should be fitted in front of the caravan road wheels, but if fitting in this position is
not possible because of obstacles or a too high hitch ball weight, it is permissible to fit it to the rear of the
wheels by rotating the whole assembly (Fig. 1) by 180° degrees.
Loosely fit the two clamping assemblies (7) to the chassis (Fig. 2 & 13) and attach. Use the bolts M10x60, nuts
M10 and washers M10 (8,17,18) and put them in the diagonal positioned holes of the aluminium chassis clamp
plates. Nuts must be no more than finger-tight.
Assemble the pre-mounted manoeuvring system on the aluminium chassis clamp plates by using the two U-
shaped brackets (9), bolts M10x50, nuts M10 and washers M10 (16,17,18). Nuts must be no more than finger-
tight.
Make sure that aluminium drive rollers of the motors are approximately on the same altitude as the centre
(axle) of the caravan wheel (0mm~40mm, see Fig. 10). As well make sure that between the top of the motor
housing and the floor of the caravan is minimal 20mm space to make sure the motors can move freely (see Fig.
10 & 15). To compensate a possible unevenness (and lower the motors), EN
DURO
®
has a set of distance plates
available. One set can compensate 15mm. In total three sets can be used so that an altitude of 45mm can be
compensated.
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro EM305 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro EM305 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 5,36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info