598281

Enduro EM303A Manual

38
Zoom out
Zoom in
Previous page
1/56
Next page
enduro
®
EM303A 33
Ref: EM303A-UM-TKI-1211-Rev.A.
Red LED (Fig. 3D) is blinking (2Hz, 6 times blinking, break, 6 times blinking, break etc.): Amp overload
protection is activated. Wait about 60 seconds and try again.
In general all error messages will reset automatically after one minute. If this is not the case, reset the
electronics of the manoeuvring system by switching off the system via the isolation switch and the remote
control handset for at least 15 seconds and then turning it on again.
The Reset Button (Fig. 3A): The remote control handset and the control unit are synchronised with each other
in the factory. If the control unit or the remote control handset is replaced, they must be re-synchronised as
described below:
• Check the installation in accordance with the installation instructions and ensure that the drive rollers are
not applied. Check that the battery is properly connected, check the condition of the battery and that a
voltage of 12 V is present at the control unit.
• Please ensure that the battery isolation Switch is on.
• Press the reset button (Fig. 3A) on the control unit and hold down. The green LED (Fig. 3B) flashes slowly.
• Activate the remote control handset by sliding the slide switch to “On”-I (Fig. 5A). The green LED on the
control unit (Fig. 3B) starts to flash rapidly. The remote control handset and the control unit are now
synchronised to each other. Finally push the reset button (Fig. 3A) on the control unit again to complete
the re-synchronisation.
• After successful synchronisation, the green LED on the control unit (Fig. 3B) and on the remote control
handset (Fig. 5H) will illuminate continuously.
OPERATION - GETTING STARTED
Please make sure you read the safety instructions very carefully and make sure that you
follow these guidelines!
Make sure that the battery that supplies the system is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on. Also make sure
that the corner steady feet are fully raised.
Turn on the battery power isolation switch (29).
Activate the enduro
®
manoeuvring system by move slide switch to “On”-I on the remote control (Fig. 5A). The
green LED (Fig. 5H) on the remote control handset will illuminate and you will hear a short beep. The remote
control is ready for use.
Press at the same time, during at least three seconds, the two buttons for engaging the motor powered rollers
(Fig. 5I). The blue LED (Fig. 5H) will blink fast during these three seconds and every second there will be a
beep. This warns you that the system will be activated!
After these three seconds the motor powered rollers will be pressed against the tyre and the blue LED will
illuminate constant. Now you can release the two buttons. When the motor powered rollers are pressed on the
tyre strongly enough, the blue LED will switch off and is the system ready to manoeuvre. The colour of the
traction indicator label (Fig.11A) should be into the green area.
Before operating the manoeuvring system, release the handbrake.
Now you can choose the movements according the symbols shown on the remote control. Straight forward (Fig.
5B), straight reverse (Fig. 5C), left forward (Fig. 5D), left reverse (Fig. 5F), right forward (Fig. 5E), right
reverse (Fig. 5G). In addition, the ‘left forward’ and ‘right reverse’ buttons or ‘right forward’ and ‘left reverse’
buttons may be pressed at the same time to turn the caravan around on its own axis (without moving forward
or backward).
When you drive straight forwards or reverse (press button B or C), it is also possible to adjust the direction by
additional pressing button D or E (when driving forwards) or button F or G (when driving reverse).
Because of the “soft start” technology, the caravan will slowly speed up. Because of the “soft stop” technology,
the caravan will stop slowly. This allows you to manoeuvre your caravan even more accurately without any
shocks.
WARNING: When the buttons on the remote control handset are released, the caravan will
slowly stop after 0.5 second and continue to move about 6cm (depending on final speed).
When the buttons of the remote control handset are released when the system is still in the
“soft start” stage (slowly speed up), the caravan will stop immediately.
After the “soft start” stage the caravan moves according one fixed speed. The speed can increase a little when
going downhill and decrease a little when going uphill. TIP: The manoeuvring system is more efficient when
reversing the caravan up an incline.
… 38 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Enduro EM303A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Enduro EM303A in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info