Manual Enda ET2011 PID (page 2 of 4) (English)

659300

Zoom out

Zoom in

1/4

SET

C.s.lo.= Control set point lower limit.(for

selected output)

Adjustable between 0 and C.s.Hi.

C.s.Hi.= Control setpoint upper limit.(for

selected output)

Adjustable between C.s.Lo. and Upper scale

value.

a2.s.l= Alarm2 set value lower limit.

Adjustable between 0 and A2.S.H

parameter value.

a2.s.H= Alarm2 set value upper limit.

Adjustable between A2.S.L

parameter value and upper scale

value.

a2.Hy = Hysteresis of the Alarm2

output.

Adjustable between 1 and 50 °C.

A2.st. = The state of Alarm2 output.

Hi = If A2 output is above the set

value. (on)

lo = If A2 output is above the set

value (off).

A2.Er. = State of Alarm2 output in the

case of sensor failure.

on = A2 output is probe failure (on).

off= A2 output is probe failure (off).

A2.tp = Function of Alarm2 type.

Four kinds of functions can be

selected.

indE. = Independdnt alarm

(Independent)

dE. = Deviation

bAnd = Band alarm (Band)

bAn.i = Band with inhibition

inp.t. = Input type selection.

Pt.0 = PT100 Decimal,

Pt = PT100,

FE.cn.= J type,

nc.nA.= K type,

c.cn. = T type,

p10.r.= S type,

P13.r.= R type thermocouple selection.

This parameter varies when changing

some parameters.

Unit = The temperature unit.

°C = °C, °F= °F

(This parameter varies when

changing some parameters.)

C.o.sE = Control output selection

C-A2 = C/A2 (Relay) output selection

SSR = SSR output selection

F.kE.C. = Function key setting parameter

nonE = Function key is off.

C2.S.A. = The function key with 2.set value is used.

manu. = Manual mode can be achieved with the function key.

dSP.o. = Only the temperature display mode is entered with

function key.

C. Pb = Proportional band.(for selected

output)

Adjustable between %0.0 and %100.0.

C. Pb = %0.0,On-Off control is selected.

C. ti = Integral time.(for selected output)

Adjustable between 0 and 100.0 minutes.

C. ti = 0.0,integral impact is disable.

parameter is different from “0”,this

parameter appears.

C. Pb

C.Hys = Hysteresis of the output.(for

selected output)

Adjustable between 1 and 50 °C.

= 0,this parameter is active.C. Pb

C. td = Derivative time.(for selected output)

Asjustable between 0.00 and 25.00 minutes.

C. td = 0.0, derivative time is disabled.

parameter is different from”0”,this

parameter appears.

C. Pb

C. Ct. = Period time.(for selected output)

Adjustable between 1 and 250 second.

parameter is different is different

from“0”,this parameter appears.

C. Pb

C.p.st = The ratio of output power at the

setpoint.Adjustable between %0 and %100.

C.E.P.s. = The percentage of faulty sensor

selected output power.

Adjustable between %0 and %100.

C.typ. = Control output type

C.typ. = HEAt means heating control.

C.typ. = CooL means cooling control.

While the parameter names appear, if and

keys are pressed together, returns to the program mode.

S.Cod = Security menu access

code.

It should be 2011.

Cosc. = Parameters of CoN.o.

menu security access level code.

nonE = Invisible.

P.yEs = Modification can be done.

P. no = Only visible.

m.SEt. = The percentage of manual output parameter.

Adjustable between %0 and %100.

This parameter allows manual adjustment of the output

power when the manual output selection.

C. Pb.= 0, this parameter is not seen.

If co.SE parameter is different

from C-A2, this parameter is seen.

a.2.sc. = Parameters of al2.o.

menu security access level code.

nonE = Invisible.

P.yEs = Modification can be done.

P. no = Only visible.

Co.sc. = Parameters of Conf.

menu security access level code.

nonE = Invisible.

P.yEs = Modification can be done.

P. no = Only visible.

S.t.Sc. = Parameters of S.tun.

menu security access level code.

nonE = Invisible.

P.yEs = Modification can be done.

Co.sc. = Parameters of Conf.

menu security access level code.

no = Parameter settings are not

change.

yEs = Parameter setting will be

restored.

2/4

C.s.Lo.

C.s.Hi.

C. pb

C. ti

C. td

C.p.st

C.Hys

C. Ct.

C.typ

s.s.t.s.

C.E.p.s.

Con.o.

AL2.o.

ConF.

S.tun.

SEcu.

S.Cod.

Co.sc.

m.SEt.

a.2.sc.

Cn.sc.

S.t.sc.

dEF.P.

inp.t.

Unit

fltr.

C.o.sE

offs.

s.t.Co.

F.k.E.C.

A2.S.L

A2.S.H

A2.HY

A2.tP

A2.St.

A2.Er.

SET

Programming mode

This parameter indicates the time to reach set point

value when the device is first energised.

Adjustable between 0 and 250 minutes.

If 0 is selected, soft start feature will be enable and the

device reaches set point value quickly.

Setting Pb = 0, soft start feature will be disabled.

Sst.S =Sofy starter timer set value

fLtr. = Coefficient of digital filter.

Filter for display value.

Adjustable between 1 and 200. If this parameter is 1,

digital filter runs most quick. If the parameter is 200,

the filter run most slow. The value of parameter should

be increased in interference.

oFfS. =

Offset value is added to the measurement value.

Adjusted between -100 and +100°C.The normal value is 0.

Offset value.

St.Cu = Self tune control parameter.

If both keys are pressed ,yEs

message is displayed on the screen

and selftune process is started

automatically.

If both keys are pressed, no

message is displayed on the screen

and selftune process is stopped.

SET

If key is pressed while holding key, the programming mode is enabled.

SET

Entering from the programming mode to the run mode:

If no key is pressed within 20 seconds during programming mode, the data is stored automatically and the run mode is entered.

Alternatively, the same function occurs first pressing key and key is pressing programming mode is entered.Then and keys are pressing

together, data is recorded and running mode is entered.

Modification Of Parameter Diagram

When holding key, the value of parameter flashes and using

keys the requested value can be adjusted.

If key is pressed and held 0.6 seconds, the value of the selected

parameter changes rapidly. If waited enough,the value increases 100 at each

step. After 1 second following the release of the key, initial condition is

returned.The same procedure is valid for the decrement key.

Chys

SET

SET SET

SET

C.s.lO.

inp.t.

A2.s.l

Co.sc.

C1.sE.

C.s.Hi.

Unit

A2.s.H

A2.Sc.

C2.SE.

C. PB

Fltr.

A2Hy.

Cn.Sc.

A2.SE.

C.HyS

C.o.SE.

A2.tp

S.t.Sc.

C. ti

offs.

a2.st.

dEf.P.

C. td

f.k.E.C.

a2.Er.

C. Ct.

m.sEt.

C.P.St.

C.EP.S.

S.s.t.S.

C.typ.

TC input

PT100 input

FE.cn.

C-A2

indE

P.yEs

400

P.yEs

400

P.yEs

500

4.0

1.00

nonE

HEat

-200

Pt.

-200

600

°C

600

DEFAULT PARAMETERS

Set parameters

Control output

parameters

Alarm2 output

parameters

Configuration

parameters

Self tune

parameters

Security

parameters

SET

ET2011-E-06-201408

When the self tune begins,

PIdt. message

and measurement value are shown

alternately.

After the completion of the self tune process,

st.Co. parameter is automatically changed to

no and the device returns to working mode.

If the measured temperature is higher than

90% of the set value at the beginning of the

self tune process, then tE.Hi. message is

shown alternately and the measured

temperature is waited to go below %60 of

the set value. After that, self tune operation

is started automatically.

If it is intended to abort the self tune

process, St.Co. parameter is changed to

no and key is pressed.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Enda ET2011 PID in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Enda ET2011 PID

Enda ET2011 PID User Manual - German - 4 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Enda ET2011 PID Manual

Product: