473755

Emtec H510 Manual

4
Zoom out
Zoom in
Previous page
1/74
Next page
76
Setup
Battery Installation
1. On the back of the remote, push down on the tab and lift the cover off.
2. Match the batteries to the + and - marks inside the battery case, then insert 4 AAA Alkaline
batteries.
3. Press the battery cover back into place.
Make sure you use new batteries. You can have problems with learning codes if your
batteries are old.
Battery Saver
Your remote automatically turns off if the keys are depressed for more than 30 seconds. This
will save your batteries should your remote get stuck in a place where the keys remain
depressed (e.g., between the sofa cushions). Also, the screen turns off a short time after no
keys have been pressed for a while (or a short time after a key has been stuck for 30 seconds).
The duration before the screen turns off can be adjusted from about 2 seconds to about 35
seconds, from the Setup, Advanced, Options menu, see page 18
Permanent Memory
All the devices you set up, their codes, punchthrough settings, and all your favourites, etc.,
are stored in permanent memory while you are changing batteries so you will not lose any
codes or settings stored in the remote while you are changing batteries.
Using the Wizard
After you insert the batteries the Language screen (1) appears. Choose
the language you want by pressing on the side key next to the choosen
language.
The Setup Wizard screen (2) appears. You can exit the Wizard at any
time by pressing the HOME key (located just below the screen). Press
any key at screen (2) to continue and follow the instructions on the
screens.
Pressing OK at screen (3) takes you to the next screen (4). Pressing
the Left navigation key (Back key) on the remote at screen (4) takes
you to screen (5) that has 10 yellow arrows. This is an exception to
the rule because we’re teaching you how to use the remote. But
pressing Back again at this point does take you “back.”
(2)
(3)
(4)
(5)
(1)
Try pressing the Back key a few times to go back through the Wizard
and then follow the instructions on the screens again to familiarize
yourself with how to step through the screens and go back. You can
go back and forth through the Wizard but once you’ve set up your
devices and quit to save the settings, you won’t see the Wizard again
unless you do a Master Reset.
To do a Master Reset: Press the HOME key, then select Setup,
then select Advanced, then select Clear Settings, then select Master
Clear. Note this will erase everything you have set up in the remote.
Pressing any of the 10 Side Keys (K1 thru K10) at screen (5)
takes you to the screen where you set up your first device (TV).
See next page.
Setting Up Your Devices
How to set up a TV
After you’ve been through the Wizard for the first time, the screen
(1) shown to the right appears. This is the start of the Wizard to set
up your devices (TV being the first one). Manually turn on the
device(s) to be set up (TV, VCR, etc.).
If you know your brand of TV, select Yes which results in a faster
search for your TV’s code. (Selecting No searches the complete
library of TV codes, rather than just the codes for your brand of
TV).
Pressing the Side Key next to Yes at screen (1) takes you to a screen
(2) where the most common brands are shown next to the Side Keys.
If your brand isn’t shown you can press the Side Key adjacent to
Next to show more brands, (shown alphabetically) or press the Side
Key adjacent to Back to go back to the previous screen of brands.
Note, on the very first screen of brands, the Side Key adjacent to
Back takes you to the last screen of brands (so you can go back
through the list instead of forward through it if you prefer). In this
case we selected Sony.
Screen (3) tells you to point the remote directly at your TV and
repeatedly press (but not hold) Power (or Chan Up/Down, or Play
for VCRs etc.) until your device responds. Pressing Power sends
the Power command to your TV and screen (4) shows that you’ve
selected code 1 of xx (xx will vary by brand). Keep pressing Power
until your TV responds and then press Save.
(1)
(2)
(3)
(4)
K6
K7
K8
K9
K10
K1
K2
K3
K4
K5
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emtec H510 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emtec H510 in the language / languages: English, German, Dutch, French, Italian as an attachment in your email.

The manual is 3,63 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info