64741
16
Zoom out
Zoom in
Previous page
1/36
Next page
1 1
1 1
5.4 SUBSONIC HIGHPASS CROSSOVER FREQUENCY ADJUSTMENT
When driving a subwoofer in bandpass (“BPF”) operation mode, you should also adjust the subsonic
highpass frequency. This is done by adjusting the “HPF” potentiometer. This setting depends the size
and the power handling of the installed subwoofer system. The higher the subsonic crossover fre-
quency is set, the higher the mechanical power handling of the connected subwoofer system will be.
The trade-off is reduced low end extension! The subsonic highpass can not be bypassed, when the
operation mode is set to BPF mode, but you can set the HPF potentiometer at 10Hz, so the subsonic
highpass filtering remains inaudible.
5.5 INPUT LEVEL ADJUSTMENT
To reach a maximum in dynamic response from each individual head-unit/amplifier/speaker combi-
nation, it is important to set the respective input level controls („GAIN“) of all channel pairs correctly.
Before you start, you MUST set all tone controls (Bass, Mid, Treble, Loudness etc.) and the fader
on the head unit to their neutral or center positions.
Now turn all input gain controls of the installed amplifiers anti-clockwise to their minimum positions
and start with the channel pair, that drives the subwoofer system. The lowpass level remote control - if
installed in your system configuration - should be set at a low position, so there is enough headroom
to turn up the bass volume later on.
SUBWOOFER CHANNEL
Set the volume control of your head-unit to approximately 3/4 of full volume, while playing a dynamic
piece of music. Slowly increase the input gain control of the channel pair, that drives the subwoofer(s),
by turning the GAIN control clockwise until you can just about hear distorted sounds coming out of
your subwoofer system. Reduce the main volume level on your head-unit to a medium listening level.
SATELLITE CHANNELS
Slowly increase the input gain control of the channel pair, that drives the satellite system, by turning
the GAIN potentiometer clockwise, until you reach a good tonal balance with a slight emphasis in the
bass region. Aim at a full bodied bass response.
Now slowly turn up the input GAIN control of the remaining channel pair(s) - if any - until you reach
a good tonal balance between front and rear satellites.
FINE TUNING OF ALL CROSSOVER FREQUENCY POINT SETTINGS
Finally you can attempt to fine-tune the HP and BP crossover frequencies on your amplifier, to obtain
the best sound quality of all loudspeakers connected to your car audio system.
EA 2-4-5 CH Manual (EDF).indd 16 01.03.2006 9:30:23 Uhr
16


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emphaser EA2160 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emphaser EA2160 in the language / languages: English, German as an attachment in your email.

The manual is 7,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info