Manual EMOS 6018 (page 4 of 76) (English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish)

784679

Zoom out

Zoom in

1/76

wireless sensor: transmission frequency 433 MHz, 10 mW e.r.p. max.

station power supply: 3× 1.5 V AAA batteries (not included)

adapter AC 230 V/DC 5 V, 300 mA (included)

sensor power supply: 2× 1.5 V AAA (not included)

station dimensions and weight: 17 × 192 × 127 mm, 364 g

sensor dimensions and weight: 15 × 62 × 100 mm, 54 g

Getting Started

1. Connect the adapter to the station, then insert batteries rst into the weather station (3× 1.5 V

AAA), then into the wireless sensor (2× 1.5 V AAA). The battery compartment of the sensor is

protected by screws; use a suitable screwdriver.

2. When inserting the batteries make sure the polarity is correct to avoid damaging the weather

station or sensor. Only use alkaline batteries of the same type; do not use rechargeable batteries.

3. Place the two units next to each other. The weather station will automatically detect the sensor

signal within 3 minutes. If signal from the sensor is not detected, long-press the button on

the weather station to repeat the search.

4. We recommend placing the sensor on the north side of the house. The range of the sensor may

decrease substantially in areas with large number of obstacles.

5. The sensor is resistant to dripping water; however, it should not be exposed to sustained rain.

6. Do not place the sensor onto metal objects as this will reduce its transmission range.

7. If the low battery icon is displayed, replace batteries in the sensor or weather station.

Switching Channel and Connecting Additional Sensors

1. Choose the desired channel 1, 2, or 3 for the sensor by repeatedly pressing the button. Then,

long-press the button; the icon will start ashing.

2. Unscrew the cover from the battery compartment on the rear of the sensor and set the sensor

switch to the desired sensor channel number (1, 2, 3), then insert batteries (2× 1.5 V AAA). Data

from the sensor will be loaded within 3 minutes.

3. If sensor signal is not found, remove the batteries and proceed again in accordance with steps

1 and 2 or press the TX button.

Displaying Data from Multiple Sensors, Automatic Cycling through Values from

Connected Sensors

Press the button repeatedly to display data from all connected sensors on the weather station,

one by one.

You can also activate cycling through data from all connected sensors:

1. turning on cycling

Repeatedly press the button until the display shows the icon.

Data from all 3 sensors will be shown automatically and repeatedly one after another.

2. turning o cycling

Repeatedly press the button until the icon disappears.

Radio Controlled Clock (DCF77)

The wireless sensor will automatically start searching for DCF77 (hereinafter referred to as DCF)

signal for 5 minutes after pairing with the weather station; the icon is ashing. (The DCF sensor

is located in the sensor).

Signal detected – the icon stops ashing and displays the current time with the DCF icon .

Signal not detected – DCF icon will not be displayed. DCF signal will be synchronised daily between

2:00 and 3:00 am.

Note: If the weather station detects DCF signal but the current time on the display is incorrect (e.g.

shifted ±1 hour), you must always set the correct time zone for the country where you are using the

station, see Manual Settings.

In standard conditions (at safe distance from sources of interference, such as TV sets or computer

monitors), the reception of time signal takes several minutes. If the weather station does not detect

the signal, follow these steps:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of EMOS 6018 in the language / languages: English, German, Dutch, Danish, French, Italian, Polish, Portuguese, Swedish, Spanish, Norwegian, Finnish as an attachment in your email.

The manual is 1.92 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

EMOS 6018 Manual

Product: