667129
2
Zoom out
Zoom in
Previous page
1/2
Next page
To temporary override the current set temperature,
1. Press up or down button once, the set temperature starts flashing
2. Press up or down button again until the temperature you want is displayed
3. Press to confirm the setting with shown on LCD
Now your thermostat will override the current programming and maintain the new set
and hold button for 5 seconds until disappears.
Press button M to select Auto/Manual mode. In Manual mode, the thermostat maintains a constant set
temperature manually set by the user. In Auto mode, the thermostat executes the preprogrammed schedules.
To adjust these schedules, follow the easy steps below,
To set vacation mode press and hold the up button for 5 seconds until appears. Use
same procedure to exit this mode.Vacation mode
up or down button to change the set point and wait for 5
will maintain a set temperature(default
Your thermostat has the ability to reset all settings to the factory defaults. If you are
certain you want to do this: In standby mode(when thermostat is turned off), press
If thermostat is set in AF model, press and hold the down button for 5 seconds,
floor temperature will show and it will automatically revert back to room temperature
This product should be installed by
a qualified electrician.
Installation and Wiring
86mm
mm68
Rear View
45mm
13mm
27 mm
26 m
m
Side View
60mm
mm68
86mm
4mm
mm7
LL
LOAD
(16A)
FEED
(220VAC+/-15%)
Floor Sensor
(or remote air sensor)
NN
To lock the buttons, press and hold the up and down buttons for 5 seconds until you
see a lock icon appearing, to unlock, repeat the steps above.
and hold
button M and for 5 seconds until “RES” is shown for 5 seconds on LCD.
This thermostat is fitted with a real time clock. It is essential that the clock time and day
are set accurately if you require your programmed events to start on time. Follow the
Set the Time and Day
Auto / Manual Mode
Program your thermostat
Resetting factory defaults
Lock the buttons
View floor temperature
Temporary temperature override
Vacation mode
Press the button once
Use up or down button to change the time (Hold up or down button to change
Press button again, the day of the week will flash
Press button again to accept and exit
Use up or down button to change the day of the week
Press and hold button M for 5 seconds until “Program” is shown with the Day flashing. Use up or
down button adjust the day (hold up or down button for 5 seconds to set all days the same).
Press button M again and use up or down button to set the desired temperature to be
Press button M to bring up the program 1. Use up or down button to set the start time
To skip program 2 ,3,4,5 for Saturday and Sunday, simply adjust the set temperature for program
To skip program 3 and 4, simply adjust the set temperature for program 3 and 4 to the same set
temperature as program 2.
2 ,3,4,5 to the same set temperature as program 1.
and the time will flash Step 1.
Step 2.
Step 3.
Step 4.
Step 5.
10
°C
) all the time. Press
Carefully separate the front half of the thermostat
from the back plate by placing a small flat head
terminal driver into the slots on the bottom face of
the thermostat
1
1
2
3
Carefully unplug the ribbon connector
which is plugged in to the front half of
the thermostat
2
Place the thermostat front half somewhere
safe. Terminate the thermostat as shown
in the diagrams below
3
Screw the thermostat back
plate on to the back box
4
Re-connect the thermostat ribbon cable
and clip the two halves together
5
(default 06:30).(Hold up or down button to change by 15 minutes each time.)
Programme Start time Setpoint
maintained for program 1.(default 21
°C
)
below easy steps,
by 15 minutes each time.)
seconds to accept and exit.
temperature until the next program period begins. To cancel the override setting, press
in 5 seconds.
CS-11 LCD 7-Day 5+2 Programmable Digital Thermostat
U9310044
Wiring Diagram
123456
SWL
Sensor
Remote
out used
L
Not
230V AC
N
~
~
Registered Address: 6 Tannery Yard, Witney Street, Burford, Oxon., OX18 4DW
Tel: 01993 824900 : www.emmeti.co.uk : e: sales@emmeti.co.uk
“ Temporary ”
“ Temporary ”
Repeat and unitl you finish the settings for 6 programmes. Press
button M to accept and exit.
The below is the default factory settings for the 6 programmes.
2 3
1
2
3
4
5
6
06:30
08:30
11:30
13:00
16:30
22:30
21°C
16°C
16°C
16°C
21°C
16°C
Note: It is faster to program the same schedule for the entire week and then to adjust the exceptional days.
1. Please ensure that the electrical wiring of the installation and connections to and from the thermostat and any remote sensor connected to it are in accordance with BS 7671, the latest edition of the IET
Wiring Regulations.
2. The thermostat must be wired to the electric mains through a switch capable of disconnecting all poles compliant with the current safety standards and with a contact separation of at least 3 mm in all poles.
3. Before commencing work on the installation, the electricity supply must be disconnected.
4. The depth of the back box should be 35mm minimum.
WARNING
Dimensions
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Emmeti CS-11 - U9310044 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Emmeti CS-11 - U9310044 in the language / languages: English as an attachment in your email.

The manual is 1,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info